Lexus GS 2013+ :: Wrapping Front Bumper Mid-section Parking Sensors
So I've seen a lot of people on here wrapping the mid section of the front bumper black to give it a more aggressive look.
For those that have done this, will I need to cut a hole for the sensors or will the sensors still work with the wrap covering them?
Elantra HD (2006-10) :: Wobble In Front End On Freeway
So I just bought an Elantra and I just took it on the freeway. At 65+mph there was a huge amount of wobble in the front of the car. It felt like I was driving in a groove in the road or driving in really high winds. The car drives fine under 60mph...
View 5 RepliesToyota - Highlander :: 2006 - Front End Vibration / Wobble At Mid
I purchased a used 2006 Toyota Highlander AWD about 4 months ago. Ever since I bought it, it has had a vibration / wobble from the front end that can be felt through the steering wheel and acceleration petal. Only happens between 40-45 mph. I have brought it to the dealer many times and every time they balance the tires. Last time they said it was a faulty motor mount and replaced it. The problem has not been fixed with this repair.
View 1 RepliesLexus RX 2004-09 :: RX330 - Vibration While Driving / When Go Over 60 Front End Starts To Wobble
I was wondering if a bad/leaking steering rack would cause a clunking sound when turning. Also if the rack is bad how many hours should it take to change?
When I am making turns I hear a clunking noise coming from the passenger side and the boot has oil on it but the fluid in the reservoir doesn't seem low.
When I am driving there is a lot of vibration and when I go over 60 the front end starts to wobble.
Lexus GS 2006-11 :: 2007 GS350 AWD Alignment - Little Wobble In Wheels
I have a weird problem with my alignment. I have had this car about a year and in April put my summer wheels on. I have a staggered set of rohana's 20x9 up front and 20x10.5 in the back. When I took the factory tires off I could see inner tire wear. I figured just needed new tires cause I don't feel any pulling or known alignment issues.
After a few months I started getting a little wobble in my wheel and more road noise on the summer wheels. When I finally got it looked at just the passenger rear tire had inner wear. I took it to get aligned and the alignment shop said this thing is really good it was all in the green. They did do a little adjustment but nothing major. Showed me the print out and everything. My car is not lowered at all. I've attached pictures......
Azera TG (2006-11) :: Heavy Grinding Noise From Front End
I have a 2006 Azera 3.3L. 72000 KMS. I have a heavy grinding noise from front end. Can't tell if left right or both sides. Changes pitch (heavier) as I speed up. Not related to eng RPM, only road speed. Is the heaviest starting at 60km/h to 80km/h then seems to level off. Begins (noticeably) around 15-20 km/h. I believe its bearing noise but have been told can be transmission or brakes. Had it on a lift with wheels off and in drive. There was no noise at slow speed. Appears to be getting worse as the days go by.
View 1 RepliesLexus GS 2006-11 :: Power Steering Felt Heavy After Starting The Car
Less than a week of driving the GS, the power steering suddenly seemed to stop working. After starting the car, the steering felt heavy (actually a good thing) but near impossible to turn during a standing stop.
Good thing I still have warranty. What turned out to be causing this?
Lexus RX 2004-09 :: Wire Coming Out Of Radio Section
I recently bought a Lexus RX 350 and I find this wire coming out of the radio section. Is this a MP3 player and if it is, how to turn it on? I look at the booklet and don't see anything about it. here is a picture of it...
View 3 RepliesLexus LS 2007+ :: Moonroof - AFT Section Not Flush With The Roof
I have a 2012 LS 460. When the moonroof is closed the aft section is not flush with the roof. It's about 1/4 inch low. I don't think this is normal.
View 2 RepliesLexus GS 2006-11 :: Passenger Airbag Disabled With Heavy Passenger In Seat
135 plus pound passenger with seat belt on. Was intermittent on/off with passenger but now seems always off (off light 'on' ) meaning the passenger airbag is disabled.
I know the es350 was so bad like this that there was a threat of class action. I've read the weight sensor is in the passenger seat rail and you can also do a calibration with a scan tool.
Golf V R32 :: Wobble Noise Coming From Right Front
Couple of days ago I started hearing a wobble noise coming from the right front. Almost sounds like a worn wheel bearing. Driving the car there is no signs of misalignment, and unbalanced wheels. Haven't hit any curbs or large potholes.
View 15 RepliesChevrolet - Malibumaxx :: 2005 - Front End Wobble?
My 2005 Malibu Maxx LT started shaking on the front end for about the past month. I took it on the highway the other day and realized that the faster I go the scarier it is to be driving it. Apparently this is a"Maxx thing" from what I have read online, but GM does not acknowledge that this happens to many owners of this vehicle and refuses to offer any solutions or reasons. So now I am stuck with it and need to figure out how to fix it.
The 2 mechanics I have taken it to assumed I was referring to the tires and said the tires look fine and there is nothing wrong the the bolts. The first guy gave the bolts a slight tightening and sent the silly woman on her way. The second guy I made drive it, he took it for 2 minutes and he said it is just lousy pavement we have in this area and that I was being paranoid. Could this be caused by tie rod issues, or maybe rack and pinion?
Ford Excursion :: 2WD V10 - Front End Shaking / Wheels Wobble
Have been battling this for months. Thought it was warped rotors, but has continued to go crazy. Truck is fine until braking at freeway speeds to 0 at about 35 front end goes crazy with shakes. Wheels physically wobble. Thought it was bearings replaced them. Put on rancho 9000 shocks replaced all steering and tie rods had aligned. Put on EDC slotted and drilled rotors with yellow stuff pads, new calipers. Each time worked for about 15 miles than started again until crazy wobble. Scaring the wife and kids to point they will no longer ride in truck. Steering is now slack need to adjust and probably need to look at everything again but it still is rectifying symptoms not problem.
View 5 RepliesDodge - Caravan :: Clunking And Some Wobble In Front End / Squeaky New Bushings
So I replaced the stabilizer bushing on my 2005 Dodge Caravan, as there was a bit of clunking and some wobble in the front end. I'm sure there's more to do (other suspension parts to replace), but the bushings were obviously worn when I looked at them. The clunking is gone, and the suspension feels better, but now the bushings make a scrunching rubber sound when I drive over uneven pavement and also when I first accelerate. I assume its the stabilizer bar flexing, but also assume I shouldn't be hearing it. After all, who would want new noisy bushings? Nothing else is new on the front end (except rotors and pads).
View 19 RepliesSonata NF (2006-10) :: At 66k Squeak And Wobble
I'm at 66k, 09 sonata gls, starting to notice a squeak here and a wobble there- I'm curious- what suspension work have you done in the 60-90k range? I have a 70 mile commute in DC so my car does a lot of stop and go. I want to take care of it and maximize life, so I'm just looking for any more common problems within the suspension.
View 7 RepliesSubaru - Outback :: 2006 - Wobble / Shudder While Accelerating
Took my 06 Outback (106K miles) in to have the right front inner & outer CV boots/axle assembly replaced (one of the boots had torn open and was slinging grease everywhere, so no surprise there). When I was driving home after picking the car up, I noticed what felt like a wobble or shudder that seemed to come from the center or right side of the car (I couldn't tell which). It would only happen while accelerating, kicking in at about 20mph and then seeming to go away at about 30mph. It didn't happen at all while coasting, braking, or decelerating. The more of a load there was on the engine, the worse the wobble/shudder was, and if I accelerated very very slowly it wouldn't happen at all or would be just barely perceptable. I didn't feel it in the steering wheel; it was more like something felt through the seat and the car itself, if that makes sense.
So I took the car back to the shop the next day, and although the owner of the shop said he drove the car and didn't notice anything, he decided to go ahead and do the job over under warranty just in case they had installed a bad axle or had otherwise "botched" (my word, not his) the job. He also rotated and rebalanced the tires on the off chance that's where the issue was. Within about 15-20 minutes of picking up the car the 2nd time, I started noticing the wobble/shudder again, always under the same conditions as I've already noted--only while accelerating, always kicking in at about 20mph and going away at about 30mph, and always worse the more of a load there was on the engine/the faster the acceleration. The only additional info I've been able to glean is that it doesn't ever seem to happen when I drive the car first thing in the morning, but starts to happen as the car warms up.
At a complete loss, I crawled under the car and starting looking and poking around for something that might be loose or knocking around. I was particularly interested in determining if there was any play in the U-joints or some kind of damage to the drive shaft. I didn't notice anything except for this--at different points on the drive shaft there are what I assume are balancing weights welded to the shaft. Well, I found a bare spot toward the rear end of the shaft that seems as if a weight used to be there (although I can't say with 100% certainty). The drive shaft is painted entirely black, as are the weights, except for this one shiny, bare-metal, square-shaped spot. "AHA" I thought to myself...balancing weight broke off (although how that would happen beats the heck out of me since it's fairly well-shielded from road debris...maybe it was just a cr@ppy weld), now the shaft is out of balance, hence the wobble/shudder. However, the more I thought about it, the more I wondered...if the shaft was out of balance, why would it only wobble while accelerating? I understand why it might only do it at certain speeds, but if a shaft is out of balance, shouldn't it wobble/shudder at those particular speeds regardless of whether I'm accelerating, decelerating, or coasting? And why would it not seem to happen until after the car had been driven for 15 minutes or so and had warmed up? Again, it seems like an out-of-balance drive shaft is going to be apparent regardless of the operating temperature of the car.
So, could I be on the right track? And if so, is the fix as simple as welding a new weight on there? Can this be done with the shaft still on the car? I think Subaru considers the shaft a non-serviceable part, but I don't want to trash and replace an otherwise perfectly good shaft for what seems like a pretty easy fix (albeit one that is probably beyond my own abilities).
Honda - Odyssey :: 2006 - Steering Wheel Wobble?
Off late my Honda Odyssey steering wheel wobble beyond 60MPH ONLY while going STRAIGHT and foot off of the GAS (which enters eco mode).My mechanic looked at it and said, it is not alignment or any mechanical issue. I looked at the other posts and I could not find any closer to this.
One more thing, I have got the Steering Pump fixed as part of a Recall ( at slow speeds, while turning makes a lot of noise)
Lexus GS 2006-11 :: Rubbing Noise Front The Front Of The Vehicle
I am on my 4th lexus; GS2010 (I currently own). I was driving off (very slow speed) from the dealership I noticed a rubbing/scrubbing noise front the front of the vehicle. The next day I started the car and backed out of my garage, put on brakes, turned the steering wheel to the far right and pressed slightly on the accelerator and I heard another noise; sounded like CV Joints going bad. So I contacted the dealer and they told me to bring the vehicle over. The noise was heard and they applied grease to something (cant remember what).
The next morning the noise was back; be mindful the noise is intermittent but mostly after the car has sat and never when the brake is applied. So I contacted Lexus and let them know the problem.
Finally I returned to Lexus, by appointment, and test drove with the lead service tech. The tech identified the noise several times during the drive; hard turns recreated the issue. Lexus contacted me and stated that they had welded something and that should ahve fixed the problem.
However the next day same problem; so I contacted Lexus again. When I returned from a business trip I returned the vehicle. On 5/23 I received a call stating that the tech could not duplicate the noise and if I could come and ride (again). So I left work and went. As soon as we got in the car (tech driving), he put the car in drive and made a sharp left turn (click, click, click); and the scrubbing noise got worse. Now instead of scrubbing on left or right hand turn, now its scrubbing going forward. So I asked why couldn't he do that without me. I had left "specific" notes as to when it happens, keep the windows rolled up, of course don't turn on radio and drive normal. So I left the car.
On 5/30 they had the vehicle fixed (yeah right); they adjusted the rear backing plate. Ok so you had my car 1 week, total time about 2+ weeks and the noise was coming from the backing plates ( I said this to myself). As usual the noise came back and I contacted Lexus. I brought the car back in on 6/13/14 and they replaced the right axle. My thoughts, if you are hearing it from both sides why wouldn't you replace both sides (??). Ok took the car home and again before I left the lexus lot, the noise was back. So I called the dealership right away. I did not turn around, I went home to pack for another business trip. Also if i would have turned around I probably would have given them a piece of my mind and that would not have been good for the situation. I was feed up so upon arrival from my business trip I scheduled an appointment with another lexus dealership; same owner but another location.
I take the car in and they call back the following week and say it was the front right caliper and it was replaced; however he stated that he didn't hear the clicking noise. I pick the car up on July 22, and by July 23, I was taking the car back. The rubbing noise they claim came from the tires and they couldn't duplicate the clicking noise. On July 29, they called me in to ride with the tech; be mindful I still have a loaner. They took me to the repair department and my car was on a lift and they dropped it down. The tech asked if I wanted to drive and I told him he could drive. I also pointed at the car that was on the lift directly beside mine and stated that by the time we get to that car you will hear the noise. he heard the noise.
On July 30, they figured out the problem and told me that they had good and bad news. The good news was they found the problem and the bad news is they can't fix it. It is a typical noise for that vehicle and it comes from the brake actuators. So I went to pick my vehicle up on next day and I asked if they bleed/flushed the brakes and he said No; and then I asked him if he replaced the actuators and he said No. So lets recount the events, You have had my car for 2 weeks with specific directions and couldn't duplicate the noise.
I come and ride with the tech and magically the noise is replicated within seconds and magically you know the problem; however you dont give me any explanation and nothing was done to confirm. That let me know they googled and came to this site and by this brake actuator issue being ongoing with no resolution they blame it on it. However the problem is that the noise is not made when braking, its made when the wheel is turned and the accelerator is inclined.
Camry 2012+ :: Repetitive Squeaking Noise From The Front - Belt Tensioner Has Constant Wobble?
I have a 2012 Camry LE 4 cylinder non-hybrid at 31,000 miles. I was changing the oil yesterday and noticed a repetitive squeaking noise from the front passenger side of the engine. Upon looking closer, the belt tensioner has a constant wobble. Maybe around 1 cm of deflection with the belt. The AC condenser was running. Is this normal? Do I need to replace the tensioner? If so, what the torque spec is for the main tensioner bolt (pivot bolt)?
View 1 Replies