Golf IV / Jetta IV :: 1999 - When Pulled Out Of Driveway Car Started Running Rough
I have a Jetta Mk IV, yesterday I went to go drive it and just as I pulled out of the driveway it started running rough, so I pulled back in the driveway and the coolant temperature sensor light came on, then the check engine light. and then it died. Then today I tried starting it, and it will only start and run if I have the gas pedal all the way to the floor, and it runs really rough. Then it will die. I thought maybe the coolant temp sensor since the light came on. I replaced that, and it still does it. I'm leaning towards a head gasket.
View 2 RepliesFord 6.0L Power Stroke Diesel :: Gear Oil Started To Leak When Pulled The Axle Out
So I replaced ball joints and hub bearings on driver side of the truck today ( passenger side tomorrow). Problem is when I pulled the axle out gear oil started to leak from axle housing not a lot but a leak nonetheless. Is this normal or did I break something.
View 2 RepliesFord F-150 (2004-2008) :: 2005 - Check Engine Light Came On And Pulled Codes P2160 And P0506
I have an 05 F-150 Lariat 5.4 and it has been going haywire today. While driving if I hit a hard bump the power will cut off (radio, a/c) and even sometimes the truck. Check engine light came on and I pulled codes P2160 & P0506. Also, when it completely cuts off and I start it back up it says "engine in failsafe mode".
View 1 RepliesCamry :: Missing While Driving With No Engine Codes
I am having trouble with drive ability. It is getting worse with no engine codes. Car idles fine, but misses. While driving and almost any speed. Drove with dealer today and he got a "misfire on 3?"
View 5 RepliesFord F-150 (2004-2008) :: Missing With No Codes / Increases With RPM
I've developed a miss no codes mild at idle horrible at 70 mph 2100 rpms driven me nuts cant figure it out cops are good just put in new plugs & gonna swap them out for a new set they were motorcraft. Sprayed water on lines & intake looking for vacuum leaks but no change....
View 7 RepliesC/K :: Truck Started Missing But Only Around 2,000 Rpm In Lower Gears
Recently with the rain and snow my truck has started missing but only around 2,000 rpm in lower gears. its a 1996 chevy k1500, it has new plug wires spark plugs and new distributor cap and rotor. When its dry outside it runs fine and everything is tight so I'm thinking it has to be the tower or coil.
View 1 RepliesFord Ranger / B-Series :: Missing When Started And CEL Came On
I have a 98 Ranger with a 3.0 (5 speed) that has 254,000 miles on it. I drove it to town this morning (8 miles) and it ran normally. I stopped for just a few minutes at a house and when I re-started the truck, it was missing very bad and the CEL came on. It wouldn't haul itself in anything higher than 3rd gear. I decided to try to make it back home. I drove it less than two miles and it cleared up and started running perfect again. I came home anyway and read the code with my scan tool.
It said that I had a miss fire on cylinder #5. I erased the codes and shut the CEL out and its been running perfectly ever since. (I have put about 150 miles on it so far) If it does it again, I will start by replacing the plug wires. I have already done that but its been a long time ago. The plugs have been replaced twice as well. I was wondering if it could be something other than electrical like a dirty injector or maybe the compression rings lined up and it momentarily lost compression.
Phaeton :: Engine Missing / Hesitation Between 1200 And 2800 Rpm - Fault Codes
What the fault codes below could be indicating. Let me quickly bring you up to speed. I was experiencing and issue with my car running rough (engine miss/hesitation) between 1200 and 2800 rpm. My ESP and CEL lights both came on. Eventually, my car stalled on me while driving. After attempting to restart the car a few times, the engine finally started. I took the car to two dealerships and was told the Mass Air Flow sensors and Intake Manifold Runner were faulty and needed replacing. After reading some of the post on the forum, I deduced the intake manifold runner would not cause the car to stall. That said, I purchased two new MAF sensors and replaced them myself to no avail. I still had the problem. I took the car to an independent mechanic (who has experience with phaetons). He hasn't been able to identify the issue. He provided me with the fault codes below:
Address 01: Engine Labels: 4D0-907-560-BGH.lbl
Part No SW: 4DO 907 560 CS HW:
Component: 4.2L V8/5VG 0030
Coding: 0007873
Shop # WSC 01065 000 00000
VCID: 79F21F7E33C272C
6 Faults Found:
[Code] ....
What I should do next. My car starts fine and idles smoothly. After driving the car for a few minutes, the engine miss/hesitation shows up.
Ford Excursion :: 2003 - Started Missing And Even Shut Off Sometimes?
I purchased an '03 V10 Excursion back in '13 with about 145000 miles on it. I've added another 30,000 in the last year and a half. It's been good but has started missing and has gotten to the point where it will shut off at times and I don't know how to troubleshoot it. The MIL has never lit from the missing. Twice after it cut off the MIL was lit with a speed sensor error.
I've purchased a BAFX Products Bluetooth OBD2 interface and I've tried a couple of different Android apps with it, right now I'm using Torque Pro. It says it's an OBD I system which I saw references to in the "Why your MIL doesn't turn on" thread. I'm seen references to using Mode 6, but everything I've read seems to indicate that's an OBD II feature.
The missing gets better and worse. Some days it will seem to be fine and then other days I have to keep it rev'ed up to keep it from dying while stopping for a red light.
When it dies, it dies while stopped in drive or reverse. It has also died a couple of times while moving in reverse while connected to a 3,500lb trailer. Every time it's died it has started right back up.
Lexus GX 2004-09 :: Engine Started Missing A Bit Then Completely Died
2008 GX470..... Car died 3 times on the way...engine started missing a bit then completely died. First time n of Dalhart TX pulled off the road and restarted in a few minutes ran ok for about 30 miles died again. Restarted in a few minutes, filled up and drove 120 miles to Trinidad CO no problems....stopped at Toyota dealer in Trinidad, ran full diagnostics, said fuel mixture would run too high, car was fine now, maybe bad gas. Drove 150 mi no problem to Co Springs. Car died again climbing up to Breckenridge, pulled into gas station, shut down, filled up, restarted and no problems the last 100 miles into Breckenridge? Only commonality when the car died was that I was at half tank of gas. If fuel pump issue should full analysis have showed that?
View 14 RepliesPassat (B5) :: 1998 - Check Engine Light On And Car Started Missing
Lets start at the beginning. About two weeks ago my girlfriend got a check engine light and the car started missing( 98 Passat 1.8T, 5 speed). Checked obvious things like fuel delivery-good. Pulled coil packs and had no spark on #2 cyl. Investigated more and found one of the pins on the ign. control module was shorted. Felt pretty sure that was the problem since everything else checked out. Ordered a Huco installed it and that fixed the problem except the car seemed slow reprogramming to the new part. I disconnected the battery to clear the memory and that seemed to do the trick.
About 2 weeks later my GF is coming home and fortunately it died in front of the apartment. Checked everything again. Getting fuel, no wires shorted on ign. or fuel harness plus they all get power just no signal when checking with an LED tester. Ign. module was good also. Checked speed sensor for resistance per the book it was good. Tried a new Camshaft Pos. Sensor hoping that was the problem, no luck. I believe it must be the computer. I'm trying to get one from a salvage yard. I don't know if the old computer can be reprogrammed or not. Also was wondering if the dealer(where I really do not want to go) can test the computer somehow and tell me if it is bad or not(don't know if I would trust them anyway), just wanted to include that option.
Ford F-150 - 1997-2003 :: 4.2L - Suddenly Started Missing Under Load
My 4.2 liter F150 suddenly started missing under load. A little background: It is a late 2003 and has 75k miles. It has been in my family since new, and I have had it for the last 4 years. This truck is as stock as they come, and has been well maintained.
On my way to work yesterday, it began missing. Not bad at first, but got worse. It misses while under load and under acceleration. The "check engine light" never came on. I have not put fuel in in several days, and it ran fine until now, so I doubt it is bad fuel. I started the engine after dark and looked for arcing. None visible, and I even sprayed the wires with a mist of water. I pulled the plugs and they all look normal. The gaps were all way too large, so I regapped the plugs to .054". I pulled the coil pack and it checks within range with my VOM. Can the coil pack be the problem even though it checks out on the bench? Can the large plug gaps have contributed to a coil pack failure?
Where to start. I HATE just throwing parts at this thing, and I don't like wasting money... If I let one of the auto parts stores run a scan, will it show a code even though I have no check engine light? I used to think of myself as a pretty good diagnostician, but then again, when I used to spend a lot of time under the hood, those cars had points, condensers and carburetors...
Ford F-150 (2004-2008) :: 2007 XLT Missing / CEL Codes Ignition Misfire 8 And Rich Fuel
My 07 xlt 4x2 4.6 (49700 miles) started missing a couple of weeks ago. Did it for 2 days, the Check Engine light came on, then it quit missing and ran normal. CE light was still on, so I had the code read and reset light. Got two codes: ignition missfire #8, and rich fuel. I assume the rich fuel was caused by raw gas in the exhaust.
Anyway, the truck ran fine for two or three days then started missing again. Checked #8 by taking the wiring connector off #8 COP - rough idle unchanged. Pulled COP off #8 and #7 and swapped. Rough idle unchanged and confirmed miss was still #8 by pulling COP connector. With #8 connected, disconnected #7 (with COP from 8) idle was significantly worse.
Replaced #8 plug. Same miss. What to check next?
Windstar :: 2001 Ford Started Missing And Stalls Randomly Under Acceleration
I have a 2001 Ford Windstar SE. 220,000 miles. A few months back it started missing ... I drove it like that just local for a few days but then I was leaving town for about a month and just parked it. After I got back I changed the plugs and all was fine on the test drive (ran perfect ... fixed the misfire). What has happened since then has been frustrating. Althought it runs great, now it stalls randomly and always when it's under acceleration and usually going up slight or a bit steeper hills (think So Cal terrain). It doesn't jerk or miss or sputter ... it just cuts out.
If you try to turn the engine over without turning the key off it won't start. Turn off the key then turn it on and it starts like nothing ever happened. No codes whatsoever. Sometimes you can drive it for 30 to 50 miles or more and have no problems at all, then all of a sudden it will stall in an area that it had no problems with over the previous week or so. It seems to stall out at about the time it wants to shift from 1st to 2nd or from 2nd to 3rd ... or at least that general rpm or accelerator pedal position. It's happened with light acceleration and heavy (pulling a long hill) acceleration. Never at idle or decelerating or just cruising on a flat piece of roadway ... never. It also seems the pedal needs to be at a constant position (not pushing down or letting up but just at a certain position under acceleration). I've had my mechanic with me 3 different times and each time it never stalled with him along. Fuel pressure was fine when he checked it (while driving).
Once in a while it will cut out (just enough to notice) then cut right back in and keep running but most of the time it just cuts out and that's it. I've changed the camshaft sensor, the crankshaft sensor, the PCM relay, the fuel pump relay, the throttle position sensor and the fuel filter. I'm hoping to set it up next week where if it stalls I can call the mechanic and have him come over to where I am and see if a code comes up (and check the fuel pressure also) without me turning it off (since that seems to reset whatever the problems is).
Toyota - Sienna :: 1999 - Started Idling Rough And Missing Intermittently?
My wife stopped for gas at a Circle K, about two days later this Sienna started idling rough and missing. I put some Seafoam in it and it cleared up. About one week later, she gets gas again, at another Circle k,about two blocks from the other one. Again, the next day she comes home from work complaining of the van running rough. I took it out and it drove fine. Whenever this happens the Check Engine light comes on, so I ran a code reader on it and it tells me, "Miss detected on cylinder 3".
So I checked all the plug wires, took out the plug (which I had just changed back in Oct.) and checked it, it looked fine. I thought maybe it could be the coil, so I switched the coil to see if I got the same code reading on a different cylinder. I unhooked the battery to clear the code after switching the coils, started it up and still got the rough idle and code. I turned it off (the van) and go in the house, I come back out and start it and it's running fine. I go to the store and all is well, go inside the store for maybe 45 minutes, come back out and start it up, I get the rough idle and missing.
I ran the code reader on it again and cleared the code, then restarted it and it was running fine again. Whatever it is, it has something to do with starting the engine (a 3.1L). One time it will start up and drive fine, the next time it starts the rough idling and missing. I figured if it was the coil and I switched them and got the same code on a different cylinder I'd narrow it down, but so far it has been running normally.
Ford Fuel System :: 2001 Excursion Started Missing / Loss Of Power
2001 Excursion 7.3 started missing the other night. Great loss of power, but made it home. Rough idle, "clacky". Next morning, did the following in order: 1) Pulled the fuel filter inspected, 2) removed all fuel from the bowl 3) replaced bowl fuel with Seafoam 4) installed new filter (my typical procedure). Without starting, I then 5) removed HPOP oil from reservoir and 6) filled with fresh oil using exact amount removed as a gauge for what to replace.
Started, idle smooth for a time. Increased rpm by depressing accelerator. Began running rougher and rougher accompanied by white smoke. Finally quit and would not restart. Cranking easily, tachometer showing RPM during crank. Suspected no fuel getting to fuel bowl. 7) Drained fuel bowl using valve on back of bowl. 8) Turned ignition to "on" to get fuel pump to run 9) removed new filter, no fuel in bowl 10) With fuel filter out of the bowl, removed fuel filter and quickly cycled the ignition to "on" and back off -- no fuel entered the bowl. 11) Removed leads from fuel pump. 12) Checked voltage across leads as ignition cycled to "on": 6.5 volts. 13) Checked fuel pump fuse (20A Maxi fuse in location 112 -- BLOWN!) 14) Replaced fuse, performed voltage test: 11.55 volts 15) Checked battery voltage: 12.44Volts.
So, with all that, how in the world does the fuel pump get 6.5 volts with the fuse blown? I looked closely at the fuse and there was no slag or connection in the element. Today I have pulled the 9-pin and 42-pin connections on the valve covers as well as the connectors to the glow plug relay module (used on Ex's) to inspect wires and connections. All looked fine. I plan to us some LP5 electro contact cleaner to clean all the connections and put some electrical grease on the connections, but the big question is where did that 6.5V come from with the fuse blown. I plan to pull the fuse and do the same test to see if the 6.5V is still there.
Ford Super Duty (1999-2016) :: Missing Bad When Started After Sitting Overnight
This is an update on an older post I took the truck to a repair shop and had it checked. They said 5 of the 8 glow plugs were not working and #3 injector was bad.. They replaced all glow plugs and the #3 injector I brought the truck home and parked it about a 20 mile drive home running fine when I got home. When I started it the next afternoon it was missing just as bad as before the work was done. After it gets warm runs ok best I can tell. What it could be? If the orings on the injectors are bad would it run ok when it warms up? Going to take it back to shop but not sure they know whats wrong by the way the mechanic talked. What to do next they have checked the wiring or at least said he did. It does ok when the oil warms up new hpop and I have checked the oil level and it was ok the hpop and eng. What else to do?
View 1 RepliesFord F-150 - 1997-2003 :: Truck Randomly Started Missing - Misfire On Both Cylinder 1 And 8
I've got a 97 f150 4.6 that has randomly started missing over the last month. It has started to get more frequent and codes are showing a misfire on both cylinder 1 and 8. Both of these cylinders run off the same coil pack. I'm thinking its the coil? The plugs and wires, motocraft, have about 3k on them and the truck runs great otherwise. I just don't know how common a coil would cause this or if they would act intermittent like this.
View 5 RepliesFord Ranger / B-Series :: 1989 2.3L - Started Missing Even Replaced Fuel Filter?
The other day I was driving down the road on a long, flat section and all of a sudden my truck started missing out of the blue. Ever since it started missing it hasn't stopped. The truck is an '89 Ranger, 2.3l, 5 spd. The plugs and wires were replaced last year along with the timing belt and fuel pump. It has been running great since then until now. I thought maybe it might be a clogged fuel filter so I replaced that but it didn't work. Also, it doesn't miss all the time. It doesn't miss when its idling or if you are going down the road while it is missing and slowly release the gas pedal it reaches a point while you are letting the pedal up where it will even out. It definitely seems like it is an "under load missing" scenario. Also, the Check Engine Light is not on. Where should I start looking?
View 4 Replies