Phaeton :: Engine Missing / Hesitation Between 1200 And 2800 Rpm - Fault Codes
What the fault codes below could be indicating. Let me quickly bring you up to speed. I was experiencing and issue with my car running rough (engine miss/hesitation) between 1200 and 2800 rpm. My ESP and CEL lights both came on. Eventually, my car stalled on me while driving. After attempting to restart the car a few times, the engine finally started. I took the car to two dealerships and was told the Mass Air Flow sensors and Intake Manifold Runner were faulty and needed replacing. After reading some of the post on the forum, I deduced the intake manifold runner would not cause the car to stall. That said, I purchased two new MAF sensors and replaced them myself to no avail. I still had the problem. I took the car to an independent mechanic (who has experience with phaetons). He hasn't been able to identify the issue. He provided me with the fault codes below:
Address 01: Engine Labels: 4D0-907-560-BGH.lbl
Part No SW: 4DO 907 560 CS HW:
Component: 4.2L V8/5VG 0030
Coding: 0007873
Shop # WSC 01065 000 00000
VCID: 79F21F7E33C272C
6 Faults Found:
[Code] ....
What I should do next. My car starts fine and idles smoothly. After driving the car for a few minutes, the engine miss/hesitation shows up.
Ford - F150 :: 1985 - Engine Missing While Driving
I've had my mechanic work on this issue (the engine misses), and for the past few months thought the issue was resolved.... Truck is 27 years old and has only 75K actual miles. Here's what I have done.
Installed rebuilt carburetor - 2009New plugs, wires, distributor cap and rotor - 2010Adjusted carburetor, timing, and choke - Feb 2012
I normally drive it every couple days, yet during last winter it set up for a couple weeks with 10% ethanol fuel. In early spring, the engine started missing while driving (about 1/3 of the time). After taking to the shop a couple times, my mechanic basically gave up. I believe it's time for a new mechanic. I may also give up and just get a newer truck, but not quite ready yet.
I suspected water in the tank, knowing that ethanol can attract moisture, so i ran the tank dry then bought 5 gallons ethanol free fuel (i live in the country where we can still find it). Engine started, ran great for a few months, and i thought i had solved the problem...until yesterday, when the engine started doing the same thing again just as it did when the problem originally started.
Camry :: Gas Filler Flap Missing And Engine Light On - Code PO446
I have a 2003 toyota solara se v6 I got the engine light on the other day and I noticed the gas cap was not good so I bought a new gas cap from the deal and put it on then my engine light went off. But now after 3,3 days of putting the new gas gap it's back on again what I noticed now is I'm missing the fuel filler neck flap (little metal round thing ) it's where you put the gas nozel to fill the tank and also it's showing the code PO446.
View 4 RepliesCamry :: 05 Solara Loses Power While Driving And Getting Codes P0172 And P2196
My Solara is running horribly. Its acting like the fuel pump or regulator is acting up as it loses power while driving and pumping the pedal usually does nothing. Its so bad that I cant drive it since top speed is about 10mph. If I just slightly touch the gas while driving I can get up to speed a little. It stalls when idling often too.
One thing I notice is if I stop driving for a while (with engine running) sometimes I can then drive away and the engine seems almost normal for 1-2 mins with lots of power. When the engine is cold it usually drives for 2 mins before these problems start.
This is a 2005 Solara. 4cyl 2AZFE gas engine - automatic - all stock - roughly 100,000 miles on the clock.
Its giving 2 codes: P0172 and P2196
I have looked up these codes and from reading I thought to try replacing the MAF sensor - no difference.
It feels like I'm driving a car with a bad carburetor again - really bogs out and laggy and sometimes even sounds like its backfiring slightly.
A bit of history:
- a few months ago I got the P0031 code so I replaced the upstream o2 sensor and all was good for a month or so.
- then about a month ago I got the P0136 code so I replaced the downstream o2 but it was starting to run badly before I could install and when I replaced it there was no change.
- last week I was surprised to see codes P0113, 172, 300, 301, 302, 303, and 136 but found that the battery terminal voltage was 10.5v so I replaced battery and those codes do not come back now.
- I'm thinking that due to the bad battery maybe the o2 sensors were not a problem? The upstream replacement made no difference (though it was running fine-just the CEL came on), and the downstream replacement made no difference (runs badly before and after).
My guess is fuel pressure, regulator, or injectors but its just getting too expensive to try.
Ford F-150 (2004-2008) :: Engine Missing While Driving - Code P0202 - Injector Circuit Malfunction Cylinder 2
Yesterday driving to work felt the engine missing, on the way home got a CEL pulled the code when I got home it was P0302, so I started with the easy and put a new coil pack, same issue, so I prayed and pulled the plug (it didn't break). Put a new plug and a second new coil pack (just to be sure, and yes I keep extras dang 5.4). cleared codes and started it this time got P0202 Ford - Injector Circuit Malfunction Cylinder 2, so I checked Ohms on #2 and it was 12.6, #1, 3, 5,6 all have 13 Ohms, didn't check #4, 7, or 8 because my big hands and the probes on my multi meter. Checked the wires on all of them and have 12 volts with key on, not running. I read another check to put blk in pin and red on pos batt terminal, and that it was supposed to go 12 to 0 off and on with engine running, All of mine went up to 14 volts and stayed no switching. Is there something I am missing to check before replacing the injector on #2?
View 6 RepliesFord - Focus :: Engine Cut Out While Driving And Would Not Restart - No Codes
I was driving my 2002 Ford Focus, when the engine cut out & would not restart.The starter cranked the engine over, I had plenty of gas,and the battery is almost new.After getting the car towed home, I hooked up an OBD II Autoscanner.The scanner showed no codes, and said the car passed the scan test.
I was expecting a sensor code, a fuel pressure code or an ignition coil code. The car had done this once before - but the code reader had correctly shown a faulty crank sensor.
I don't see any loose wires or anything obvious that popped off while driving.BTW, it was a smooth road & I was only doing about 50 mph. Where should I start troubleshooting?What would cause the engine to stop but not show a code?
Prius (2004-09) :: Engine Shutting Down While Driving - Multiple Codes
Three times recently my 2008 Touring Edition Prius has experienced a shutdown of the engine while driving. Each time I was able to coast and/or use battery power to get to a safe location. The “Triangle-of-Death” and the Check Engine Light was illuminated on the dashboard. Since my car is equipped with a scangauge, I was able to see the codes and clear them on the spot. After restarting the car, it showed no adverse reaction to shutting down and all was seemingly well until the next event. The codes listed below all seem to be communication lapses.
My question is; where do I start in my pursuit to diagnose and repair?
7/15/14 - 98,889 miles U0293 and U0100
7/23/14 - 99,414 miles U0293 and U0100
8/21/14 - 101,065 miles U0100 and U0000
LS / MKZ :: Car Started Missing - Pulled Codes Got P0308
car started missing- pulled codes got p0308 (water in plug well).Checked other wells found some oil in a few.Changed valve cover gaskets, installed new motorcraft plugs (pulled out motorcraft agsp-32F plugs, checked gap on existing plugs .044. Advanced Auto gave me agsp-32FM plugs. Gapped them same as old ones.044. Replaced CoP on cylinder 8 with a new one.Car ran worse than before, (smelled Horrible),
Decided to reinstall old plugs, Reinstalled checked for oil in wells and all dry so gasket job worked. I did find a loose CoP connector when taking apart. (did not fix the problem tho. Not sure if the plugs are different 32F old- 32FM new. not sure what the M means after the F.
Put everything back together and car is running smooth again. Took for a long drive to make sure everything is OK. When i put the pedel to floor, the car hesitates and surges. Under normal driving conditions the car seems to run fine. (no missing, smooth acceleration, smooth idle). But when i floor it hesitates and surges, but seems fine when normal driving is resumed.
Checked for codes and only pulls up a p1565. From searching other post i find that this is from a bad clock spring. Which i do have to replace (airbag light blinks 3-2, and cruise control is a little whacky. Will a bad clock spring cause the hesitation when floored?
Ford F-150 (2004-2008) :: Missing With No Codes / Increases With RPM
I've developed a miss no codes mild at idle horrible at 70 mph 2100 rpms driven me nuts cant figure it out cops are good just put in new plugs & gonna swap them out for a new set they were motorcraft. Sprayed water on lines & intake looking for vacuum leaks but no change....
View 7 RepliesCamry :: 2.4 Engine - Misfire Codes And Rough Idle
The engine on my camry 2007 was overheated and I had the headgasket replaced but now it has misfire codes and rough idle this is a 2.4 engine I replaced 2 of the coils but still it has a rough idle... when the car is running it runs pretty good.
View 5 RepliesCamry :: 2000 - Check Engine Light On But No Error Codes
A couple of weeks ago the check engine light came on and when I had the codes checked it showed a problem with the EGR valve. I replaced it and the light went off. A week later the check engine light came back on but when I had the error codes checked there weren't any. After a few days the light went off but earlier today it came back on. There are still no error codes.
I forgot to mention that it's a 2000 Camry, 6-cyl.
Toyota - Camry :: 2002 - Check Engine Light Went Out / No Codes
Car: Toyota Camry 2002 .. Mileage: 150K
Symptom:Check Engine light went on a few days ago.
Checked codes and got these (3):
1) P0420
2) P1310 and
3) P0420 P ("Pending" ?)
I also checked I/M Readiness and got these suspicious-looking values:CAT: NOT RDYEVAP: NOT RDYO2S: NOT RDYH02S: NOT RDY
NOTE all the other I/M values were N/A
Researching the Codes, it sounded like Ignition, and possibly the O2 sensor on the Catalytic Convertor. I had just had some engine work done by the dealer -- actually, replaced spark plugs -- so I figured to go back and bitch him out for screwing up my car.
A few days later, before I could engage my Rage, I went back and re-scanned. First I noticed the CEL was now OFF. Scanning, I now I get "NO CODES", and all the I/M values are now N/A; No more "NOT RDY".
What do you all make of this? Should I be concerned now that the CEL is Off, and I get No Codes with a scan?Or maybe I should take it to AutoZone for their free CEL diagnosis -- would their machine be more thorough than mine (Autel MaxioScan 300)??
Toyota - Camry :: 2000 - Check Engine Light Codes
I had my 2000 Toyota Camry with 133,921 miles on it seen because of the check engine light.The codes obtained at the repair shop were:
P0136: Oxygen Sensor CKT Malfunction Bank 1 Sensor 2
P0446: Evap Control system Vent CKT Malfunction
They then ran a smoke test and found that the charcoal canister was leaking and needed replacement. The mechanic said that not doing the above would not affect the car's performance or its safety but it would not pass inspection with the check engine light on and with those codes.
Camry :: 2000 - Check Engine Light On And Codes Are P0446 And P0401
My camry 2000 recently the engine light's on and the codes are P0446 and P0401
P0401:The PCM has determined that there is insufficient flow in the exhaust gas recirculation system.
P0446: The PCM has determined that a malfunction exits in the electrical circuit fo the vent control in the evaporative emission control system.
Ford F-150 (2004-2008) :: 2007 XLT Missing / CEL Codes Ignition Misfire 8 And Rich Fuel
My 07 xlt 4x2 4.6 (49700 miles) started missing a couple of weeks ago. Did it for 2 days, the Check Engine light came on, then it quit missing and ran normal. CE light was still on, so I had the code read and reset light. Got two codes: ignition missfire #8, and rich fuel. I assume the rich fuel was caused by raw gas in the exhaust.
Anyway, the truck ran fine for two or three days then started missing again. Checked #8 by taking the wiring connector off #8 COP - rough idle unchanged. Pulled COP off #8 and #7 and swapped. Rough idle unchanged and confirmed miss was still #8 by pulling COP connector. With #8 connected, disconnected #7 (with COP from 8) idle was significantly worse.
Replaced #8 plug. Same miss. What to check next?
Camry 2012+ :: Check Engine Light On - Codes For EVAP Emission Control System
So mad today. Check engine light came on, plugged in my scanner, got P0441 EVAP Emission Control system Purge Flow Fault and P0455 EVAP Emission Control System Leak (Large).
8-month old '13 TCH XLE is getting a check engine light already.
Ford F-150 (2004-2008) :: 2006 - Missing And Rough Idle - Codes P0340 / P0344 / P0345 And P0349?
I recently purchased my first Ford pickup. I bought a 2006 F-150 with the 5.4L 3V engine. I have only driven it for about 300 miles so far and am having problems. The engine has 146,000 miles on it. I have read several posts on here about the cam phasers which I believe that I may have some issues with. The engine will run well when cold, on the road, etc. The engine does have a slight ticking after it warms up (cam phasers?). When I come to a stop after the engine is operating temperature, the engine will start to miss and shudder and all 4 above codes come active and are also pending (8 codes in total).
All 4 codes are logged at the same time. I have replaced both cam position sensors, both sensor ends and terminals for cam position sensors, checked wiring around the rear of engine (does not appear to be rubbed through), all plugs were replaced, and all COP boots are good. Is there anything that can cause these codes that may not be the actual cam position sensors, ie. VTC, COPs, cam phasers? What pins the cam position sensors come on the ECU (so I can ohm the entire wire harness)?
Also, if the engine is missing with the codes active and I rev the engine up it will come back to idle and run great. The engine never dies out, just runs horribly. I have also unplugged each sensor with the engine running which has no effect on the way it runs.
Ford Super Duty (1999-2016) :: 2008 F250 V10 Missing / Dead / No Power And Multiple Codes
I have a 2008 f250 superduty with the v10. Just today I was driving and engine picked up.slight miss it's rainy. I thought coil pack, but it left me on side of road. Got fired limped home won't go more than 40mph. Runs rough, no power, checked codes and get P0340, p0357, p1336, and P2195.. Where to start.. My daily driver and have to get back on road.
View 1 RepliesFord 7.3L Power Stroke (1999-2003) :: 2000 F350 - Missing After Start Up - High Idle - Got Codes P1316 / P1211?
Well, long story is that I starting have problems with my 2000 F350 Dually 7.3 PSD about 6 months ago ( ~10K miles ago ). I have sunk almost 5K$ in mechanics and the problem is still present.
By troubleshoot, I do not mean try this, try this, as that has been what is happening. I mean making test measurements and diagnostics. I am fairly mechanically inclined, but I am no mechanic. Looking for primers on how the 7.3 PSD works.
Symptoms: After the truck sits 12 to 14 hours, it starts and idles fine ( ~ 700 RPM on the 'Dash Tach' ) just as it has always done. During the first 5 miles of driving it, the SES light comes on and it sputters, stalls, and vibrates as if a couple of the injectors are not firing. It then clears up and the SES light goes out, except that it idles at about 1200 RPM ( 'Dash Tach' ).
It runs fine like this the rest of the day, If I shut it down it will start right up and run fine, but it has the high idles. Only if it is shut down longer than 12 to 16 hours do the symptoms, other than the high idle, reappear. The high idle is constant. Also mpg have fallen ( 13 opposed to 16 ).
It does not seem to be related to ambient temperature, or the amount of warm-up idle. I have idled it for three hours on startup and it is fine, until I drive the first 5 miles or so.
Now, I have had three mechanics work on it and they have replaced: the ICP sensor ( 3 times ), the Fuel filter ( twice ), drained, flushed and refilled the HPOP, replaced both sides of the valve cover wiring harness, put in a new IDM, fuel heater, CPS sensor ( 3 times ), fuel pump in fuel tank, EBPV ( not sure what this is ), and the last straw was saying the injectors needed to be replaced ( or at least the O-rings, but while we are in there you might as well ... ).
I bought a cheap code reader and it says: P1316 & P1211. I believe these are the same codes since day 1.