Jeep - Liberty :: Idling Rough With No Error Codes - Multiple Cylinder Misfire
ODB2 Code: P0300 - Multiple Miss-fire
I have an issue with my Jeep Liberty. It started idling rough with no error codes. about a week later it through the Multiple misfire code. I started by replacing the spark plugs. The old ones were from 20K miles ago and still looked good. Replaced them anyway. I still had the code. I put K44 fuel injector cleaner into the tank and drove it home (2 miles.) The next morning I started it and went in side because I had forgotten something. I came out to extremely thick black smoke. It went away after about 2 minutes, the computer code cleared, and the engine idled perfectly. About 2000 miles later the car is once again idling poorly. I added K44 again and for that tank of gas it ran fine, no code. Once new gas was added it threw the same error code and idles very roughly.
So here are some basic info pieces:
1. 8 tanks of gas from 8 different locations.
2. Adding K44 has shown a direct improvement both times, but more significant the 1st time.
3. New spark plugs
4. New coil packs
5. 2005 Jeep Liberty - 3.7L V6 at 99,872 miles
6. Hopefully unrelated is that the car has a small radiator fluid leak I haven't found. It requires 1/2 gallon every 2K miles or so.
There is no knocking sound, it just sounds like there isn't enough gas. Car responds fine to accelerator. Above 10mph car seems to drive smoothly.
Jeep - Cylinder - Liberty :: 2001 - Spewing Black Smoke Out Of Tailpipe / Misfiring
I have a 2001 Jeep Liberty Sport 4x4. 150,000 miles. I had the ignition coil changed on cylinder #5 last weekend and then this weekend it started spewing black smoke out the tailpipe. Dealer says cylinder #2 is misfiring and he would have to replace the cylinder head. The main issue is that the part is backordered for an indefinite amount of time so I have no way to know if or when it could be fixed. If it could be fixed there wold be no guarantee it would work for much longer. It is obviously cheaper to repair the car than get a new one, but at some point the is the law of diminishing returns...
View 12 RepliesJeep - Liberty :: Check Engine Light - Code PO299 Came Up
I have a 2006 Jeep Liberty 2.8 Diesel. It has about 57000 miles on it and when I took it to be inspected, a Code PO 299 came up. The dealer has done quite a bit of work to it and cannot find a way to get this light to stay off. When something is done, it goes off until it is driven, then it comes on again. So far the jeep runs great, but it's hard to pass inspection unless the light goes out.
View 7 RepliesAccent MC (2006-11) :: Cylinder 3 Misfire After Fuel Injector Cleaning
Make: Hyundai
Model: Accent
Year: 2007
Mileage: 70K
I've added Mystery Oil into my gas tank to clean fuel injectors as a maintenance precaution. I added it to a full tank of gas, when the gas tank was on low and I needed to get more gas, the check engine light came on.
The car was diagnosed with CEL reader from Autozone, misfire in cyl 3 is what the guy said. 3 full gas tanks later, it still has the same code and the car idles rough, hesitates and only seems to behave normal under medium to full throttle at higher RPMs.
I've been reading online for similar issues, as well as asking my friend who works as a mechanic at a dealership. Everyone seems to be accepting this behavior as normal and suggesting to wait out a couple of more gas tanks for the fuel injector cleaner to burn through.
I've looked at the spark plugs. 1,2, and 4 cylinder spark plugs have normal wear and tear. #3 has black build up, which corresponds with online pictures of rich mixture misfire.
I'm looking for a repair manual on another thread on this forum so I can take the injector from cylinder #3 out and look at it.
Ford Aerostar :: 1996 - Consistent Misfire On Cylinder 6 / Fuel Injector Change
My 96 4wd 4.0 Auto has a consistent misfire in the #6 cylinder. I've change out the plugs and wires and am considering changing the fuel injector for that cylinder. Looking it over last night, got me wondering if there is a way to change out the fuel injector without removing the upper intake manifold and the entire fuel rail. As you all know, these things are a beast to work on when the engine is in place. So, is it possible? Inquiring minds want to know (and don't want to spend an entire weekend changing out on fuel injector if there is an easier way )
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: 1271 Injector Code - High Side To Low Side Open Cylinder 1
I've got a 1271 code and I can't seem to make it go away. Code definition is "High side to Low side open Cyl 1". The truck runs fine, no rough idle, no excessive smoke of any color, just the damn CEL light stays on. I check the UVCH and all the injectors ohm in at 2.7 ohms. I've already done the updated clips under the covers. I run all the buzz tests and KOEO/ KOER tests and all appears OK. My AE won't do a Cyl contribution test. All the injector data shows all 0.00. I know its not that perfect. "high to low open", does that mean I've lost a ground? If so where?
View 14 RepliesSilverado :: 2003 - Intermittent CEL Code P0304 / Misfire On Cylinder 4
My 2003 Silverado 5.3 has an intermittent CEL. I plugged in the reader and found code P0304, misfire #4 cylinder. I changed the coil, swapped the spark plug and wire from #2 cylinder to see if the code would follow. Nope, didn't follow. I swapped the injector also, same results. My daughter decided to borrow the truck and drove it so low on fuel that the low fuel light came on in the drive way. I added about 4 gallons of fuel and now the light went off. I started the engine after a jump start, and the engine really runs rough and now won't stay running. I am thinking that the fuel filter is probably needing changed because of how low the fuel.
I haven't checked the fuel pressure yet and will do that today. Now, what really puzzles me is the intermittent part. Sometimes it will run with no problem, but then the CEL will come on and the fun begins. The Chevrolet dealer says it's caused by the valves turning in the head and when it reaches a certain spot, it detects the misfiring #4 cylinder resulting in the CEL. If I pull in the driveway with the engine missing, go back out in a short time, start the engine and it runs fine. Same thing if it's running fine and I can start it and the CEL blinks and it begins missing, but may stop and run fine. I am stumped and not so sure about the turning valves.
Ford F-150 - 1997-2003 :: Code P0306 - Cylinder 6 Misfire
So my 99 F-150, 4.2L started throwing a code a few weeks ago, P0306 #6 Cyl Misfire. This thing has got 238,000 and has been the most reliable commute vehicle I've owned.
Today I changed all the plugs and wires (they were due anyways) which didn't resolve the issue. After clearing the code, got about 3 miles out and it came back. Running SeaFoam through the system on this tank as well, but I'm leaning towards an EGR blockage like what is described here:
Sparky's Answers: 1999 Ford F150, P0306 Misfire Cylinder #6
I was about to buy a new coil pack but I'd rather not continue to throw parts at this, as I've read many others do with this same exact situation, only to end up with the same code. I've replaced the coil pack once already a few years ago when I lost a cylinder on the way to work.
Ford F-150 - 1997-2003 :: CEL Code P0301 / Misfire With Cylinder 1
My 97 F150 through a CEL Tuesday night P0301 so I picked up a new plug because it's cheap and simple, but that didn't do anything. Spark plug wires are about 3 months old, I also swapped injectors between 1 and 2, and misfire stayed with cylinder 1. It also gained a tap when the misfire started but only above idle, but it doesn't sound like a rod knock.
I also noticed if you unplug injector 1at idle it taps/knocks 3 or 4 times, however if you unplug any of the others it doesn't do that. I checked and I definitely have good spark from the plug. I plan on picking up a new compression tester tomorrow since mine never was returned. If you take the oil fill cap off it doesn't have any blow by at idle, however if you rev it you get a quick cloud out of it.
I thought about picking up a kit to check the injector pulse.
Ford F-150 - 1997-2003 :: Code PO304 - Cylinder 4 Misfire
I have a '98 F150 4X2 extended cab with a 4.2l with 233K on it. I have no problem with drivability when I drive 5 miles to work. However, a couple of weeks ago when I had to drive 15 miles to the liquor store to get what I needed (I live in a dry county) I got back into my truck, started it and drove of. It drove like crap like I lost a cylinder. Drove it back home those 15 miles, let it cool off, put my scanner on it and got a PO304 code and I think a PO174 (bank 2 lean) code. Went to the #4 cylinder and found the plug had loosened up.
Tightened it back up, cleared the codes, and went through my normal weekly routine of driving to work with no problem. Made a booze run the next weekend and the same thing happened. Limped back home and found another PO304 code. Found the plug to be tight and in good condition but changed all the plugs since they were cheap copper core and had 20K on them. The wires only have 20K on them, too. Installed platinum plugs, drove all week 5 miles to work and back just fine. Made another 15 mile run yesterday and the same crap happened all over again after I got out of the store and drove home.
Elantra XD (2001-06) :: 2003 - Code P0303 Misfire Detected On Cylinder 3
2003 hyundai accentra and I have trouble code P0303 misfire detected cylinder 3 the car would run rough and hesitate at idle and run rough in drive and reverse I checked the plug gap on number 3 cylinder and it was excessive so I regapped it and put back and the car run good for about a day and now the engine light is back and is running rough and hesitating.
View 1 RepliesFord - F150 :: 2003 - Code P0301 / Misfire On Cylinder 1 Keeps On Coming
I am at about my wits end with this P0301 (Misfire On Cylinder #1) code on my 2003 Ford F150 4.6L. I've replaced the coil pack on that cylinder, all the spark plugs, and replaced the fuel injector on that cylinder. We keep clearing the code and it keeps on coming back.
The weird thing is that it only misfires after the truck has set for a few hours and then it only misfires when I first put it in gear. Once I am out of the driveway and on the road it's fine for most of the day unless I let it sit for several hours and then it might misfire again.
We noticed that the connector to the fuel injector is wobbly and doesn't snap tight to the fuel injector (before and after it was replaced) due to the clips on the side not working well. We zip tied it together this afternoon to make it fit tightly to the fuel injector to see if that works.
What could be causing this? Other than that misfire the engine sounds great and the trucks runs very well.
Ford F-150 - 1997-2003 :: 1998 - Cylinder 1 Misfire / Code P0301
I have a 98 F150 4.2L with code P0301 Cylinder 1 Misfire.
This is what I have done so far. New plugs, coil pack, plug wires, TPS, EGR, EGR Vacuum control regualier, DMCP, canister, all of these parts are new and was bought from the ford place. Have taken the egr value, and egr value bracket off to see if carbon blockage was present, but it was clean. It was clean in the motor also. Have blown air through the metal tube that connects to the egr value and it come out the tail pipe very good, so no blockage their. Have cleaned throtle body and injectors. Have tested fuel injector with tester and it works correctly. Motor holder pressure. Have correct fuel pressure.
Do not have any vacuum leaks, it holds vacuum correctly. Crankshaft sensor is fine. Went throw 4 cans of break parts cleaner, spraying on intake while motor was running, motor did not idle up or change. I have done all this and it still shows code P0301, and it still skips. Here's the catch, if you unplug the vaccum off the egr the misfire goes away, or unplug the EGR vacuum control regulator it goes away, or if you unplug the DMCP sensor it goes away, it does not matter witch one you unplug, the misfire goes away.
I have had several different test done the the truck, but all the test only show that one code P0301, they do not show any other codes, or problem's with my truck.
Ford F-150 - 1997-2003 :: P0307 Fault Code - Misfire On Cylinder 7
I have a 2001 King Ranch F150, which has a 2004 Lincoln Navigator 5.4 DOHC Intech engine installed. The engine was installed in 2005 and had less that 100 miles on it. The engine now has approximately 95000 miles and I have recently gotten a P0307 fault-miss fire on # 7 cylinder. I have installed a new spark plug, COP, and fuel injector. The fault has returned. What is the cause of my problem?
View 1 RepliesFord F-150 - 1997-2003 :: 2002 - Cylinder Misfire And A Lean Code
My truck was running fine the past few days minus a cylinder misfire and a lean code the misfire was due to a coil pack being out no big deal on that part but yesterday on 7/30/13 my temp gauge turned off my truck wouldn't go below 1k rpms and then the over heating light came on. i drove the one mile home and turned it off an hour later i went back out to my truck to get to work and it refused to start.
I decided to just hold my foot down on the gas and crank it and it eventually started drove it to work with the same symptoms. now today its doing the same thing except now the truck is broke down in the parking lot at my job the engine is flooding cause i can smell it last night i changed the thermostat. I can get so that i can get my truck up in running its a 2002 f150 5.4L 4x4....
Jeep - Liberty :: 2003 - CEL Has Been On And Engine Knocks
2003 Jeep Liberty Sport, 156 K miles, Check engine light has been on for months now. First occurrence was when driving, and car started to knock as though I was shooting 50 cal machine guns. Stopped vehicle, shut off, and upon restart, engine ran smooth. Now, almost every time after engine has been running a while, and I am going on a down slope, the check engine light starts to blink, and engine starts to miss. Took to my mechanic, and so far, I have been told and have replaced, Fuel pump, Spark plugs, coils, and wires, cam sensor. Latest and most recent with promise that this has to be it, I replaced engine computer.
View 16 RepliesFord F-150 - 1997-2003 :: CEL Code Signifying A Cylinder 3 Misfire - Shudder / Hesitation
I will add as many details as possible :
2000 f150 4x4 offroad package
5.4L with 131k on it
new Dorman intake manifold
new Global Automotive (Ebay) COPs
New Motorcraft spark plugs
About 1500 miles ago I started throwing a code signifying a cylinder 3 misfire. The truck would bog down real bad and then after 5-6 seconds of no power it would return to normal. I tried replacing the COP (both with new and then with one from another cylinder) and plugs but no resolution. So I talked to the local ford service manager and he said it sounded like intake manifold problems.
Replaced the intake manifold and no more codes were being thrown.
1500 miles later and today the truck started having a hesitation/shudder when I was sitting in a drive-thru. I put the truck in neutral and park and neither solved the issue. With the earlier issue, when I would put in neutral and increased rpm, the issue would resolve.
I pulled out of the drive-thru and the hesitation was consistent no matter what the rpm or speed. The truck feels almost sluggish and lacks power. The hesitation is like 2x/second. When accelerating its almost like the rpms and speed hesitate, jump, hesitate, jump.
Ford 6.0L Power Stroke Diesel :: 2003 - Cylinder 5 Misfire Code P2285
I'm normally in the 7.3 forum, but a friend has a 2003 6.0 with a P2285. I get the impression that on the 03 and early 04 models, this code is nearly always a failed ICP sensor or the wiring leading to it. It also has a cylinder 5 misfire code, but I suspect that's a separate issue. I had the truck hooked up and the ICP held pretty much steady at 870 psi. I didn't look at ICP voltage, but I'm willing to bet it was probably 0v and the pressure reading was inferred and not actual.
Will a failed ICP sensor also cause the truck to have decreased power? Any tips to make the sensor easier to change, like a certain socket/ratchet combination or anything? Is it easier from the top, or bottom? I do have a lift . . .
Ford Super Duty (1999-2016) :: 2003 - Cylinder 3 Misfire With No Code?
my 03 f250 has a 5.4 and i cant seem to get rid of a misfire in cylinder 3. i had a p0353 code but that no longer shows up. i replaced all the coils with Accel coils, replaced the plugs with motorcraft platinum. i have checked the wire all the way back to the PCM and it checks out. i replaced the pcm with one that has been reprogrammed. i have swapped the injector and coil with another position and still get misfire at #3. Replaced the coil connector with a new one. I have good fuel pressure. I no longer get the code but the misfire is still there, unplug the coil and injector while running and no change. Unplug a different cylinder and you can tell the change. I checked compression and its good. I am lost here!!!!
View 14 Replies