Ford Ranger / B-Series :: New Clutch - Hard To Shift Going Into 1st / 2nd And Reverse Intermittently
1997 Ranger extended cab, 222k mi., 4 cyl, standard transmission. Shifting got worse until it finally died and the mechanic replaced the clutch "kit" and slave cylinder.
It still fights back going into 1st, 2nd, and reverse. But it is intermittent. If I put it in neutral, depress the clutch, and start the vehicle, then, after a few seconds wait, when I try to go into 1st (or reverse), it fights me back, forcing me to pause and apply about twice the pressure I should need to go into gear. When I go forward in 1st, and am ready to shift to 2nd, it fights back so that I have to pause just a bit and apply more pressure than I should for it to go into 2nd gear. 3rd, 4th, and overdrive are FINE. Also, the clutch seems to disengage about halfway down, where I was expecting it to disengage after only 10 -20% depression.
The mechanic doesn't see the problem (or won't admit it). Is there an adjustment to make the clutch disengage with only 10-20% depression instead of the 50%? Is that something I should be worrying about?
Is there some other problem? Like maybe the synchromesh mechanism in the transmission itself not bringing the transmission rotor to engine speed soon enough (wear on the synchromesh)?
When it was new, it went into ALL gears with ease, no fighting back, and it starrted doing this after about 150k miles. Now, at 222k mi., even with a new clutch, plate, throughout bearing, and slave cylinder, it still seems partially stuck going into 1st, 2nd, and reverse.
I just don't want to start replacing things until I can get a correct diagnosis as to what is causing the problem.
Ford Ranger / B-Series :: 2003 - Hard Shift - Transmission Or Clutch?
The truck: 03 Ranger, 2wd, 2.3L, 5spd, 160k mi
I bought the truck two years ago and it's always been difficult to shift (especially into 1st, 2nd, 3rd). I don't drive it often and only put 5k mi on it since I bought it.
The problem: Someone more mechanically inclined than I once told me that the hard shifting is probably due to the clutch not fully releasing due to low hydraulic pressure brought about by a failing slave cylinder.
I just noticed today that there is a high-pitched squeaking coming from somewhere on the truck. At first, I thought it was the rear end, but now, after pulling it into the driveway, I noticed that the squeaking noise vanishes when I push in the clutch pedal and returns after I release the clutch pedal and drive in 1st gear.
The transmission oil level is good, but I've never changed it and I'm not sure if the previous owner ever did either. I'm hoping I haven't damaged the transmission.
After reading a few threads, it seems the problem might be the input shaft bearing. To replace it, I'd need to drop the transmission and borrow a couple of tools I don't have (feeler gauge and bearing puller). If the ISB is the problem, it seems like it would be a good idea to change it now before it seizes and leaves me stranded somewhere.
Civic - Honda :: 1996 - Lose Clutch - Hard Shift Into 1st On High Speed?
,My wife drives a 96 Civic DX Hatchback, 5 Speed. It has about 160,000 miles on it, and she only drives it to work and back (a 15 minute drive via the interstate).
Just yesterday, she told me that the clutch feels 'looser' than normal, for lack of a better term. When it's first started, it's hard for her to get it into first and/or reverse, but once driving, she says the shifting is fine. When she's driving at highway speeds in 5th for a while, then has to get off at her exit, she said it's hard for her to get it back into 1st gear. She says she feels like she has to push the clutch harder than normal to get it back into 1st gear.
I don't know much about manual transmissions, and am hoping for some insight into what the problem(s) may be?
GTI 337/20th Anniversary :: Clutch Sticking When Released And Gears Only Engage When Push Hard Shift Knob
Been having trouble shifting into any gears on these chilly mornings in VA now... The clutch has been sticking on its way out when I release it and the gears don't want to engage unless I really push hard on the shift knob.
View 11 RepliesGolf IV / Jetta IV :: Clutch Never Came Back Up When Trying To Shift
So i was driving and I went to shift and my clutch never came back up. Long story short after searching the forums i think it might be my slave cylinder and throwout bearing. There was a puddle of fluid under the car.
I was planning on using this DIY : [URL] ....
Just wondering if all i have to do is follow this up to step 48 and replace the throwout bearing and slave cylinder.
Golf/GTI VI :: Clutch Getting Harder To Depress When Go To Shift
So, For the past week or so, I've been noticing that my clutch has been getting harder and harder to depress when I go to shift. I only have 1500 miles on the car and picked it up 3 weeks ago. When I took delivery, the cars clutch was silky smooth.
This "tightness" is almost as bad as my 6MT clutch on my old subaru (which needed to be replaced because the spring on the pressure plate tightened). What could be making the clutch feel so heavy? I'm not too familiar with the VW clutch. Is it hydraulically actuated? If so, maybe the fluid is low or leaking?
Golf IV R32 :: Whine Sound When Press The Clutch To Shift At High RPM
My R is stock. When I accelerate hard and shift, I can hear like a whine noise when I press the clutch to shift.
Its like something continue to spin fast when I press the clutch at high rpm.
Golf/GTI VI :: High Revving When Shift Into Neutral Or Push In The Clutch
I just brought my gti in for the 20K oil change etc... I have noticed something weird... when I accelerate hard or have been driving for a while, and then shift into neutral or push in the clutch, the engine revs up to almost 2K, then back down to 1K once or twice, then finally settles to 700rpm's. It doesn't do it cold, or when I have the AC running.
I have no CEL's, and the dealer just said they ran a fault check, and it was clear. I do have an APR exhaust and a K&N intake (I think stage1 tune)... I asked about the PCV valve, and they said that would throw a code... They said they could do additional diagnostics out of warranty, since they think it has to be part of my aftermarket stuff.
I don't know if it's related, but if I really jump on it, in 5th gear or so, I can hear the car losing a little rpm's then around 4K just for a second, then it's goes back to normal... This only happened once or twice, so maybe it was just in my head...
Golf VI R :: Really Hard To Shift Into 1st Gear
I just finished the DG install yesterday. I am having a real problem with the first gear: it is really hard to shift into it (I mean hard!) - and several times I went into 3rd believing it was in 1st, while driving. I know that the DG is notchy and a little stiffer (which I like) but this does not feel right. I have to really push hard (moving slightly toward reverse) to shift into 1st. My wife would never be able to find it or shift into it (not that I let her drive my R that much...).
Note that all the other gears (2,3,4,5,6 and reverse) shift beautifully without any effort with that nice click. But not 1st.
What is it? Adjustment? I did it twice. I made sure that both cables were "all the way in" before tightening the first two bolts (and I made sure that the cables were not moving - a common problem with this install) with the engine lock on and pin in.
Golf/GTI VI :: Hard To Shift In 2nd Gear When Cold
2011 TDi 6 Speed (Sportwagon) with problems shifting into 2nd? Mine is currently in the shop under investigation for a balky shift when cold. The tech says it's not right, but then they find another vehicle in inventory with the same issue...currently waiting on a VW engineer.
View 16 RepliesGolf IV / Jetta IV :: Hard To Shift Into 1st And Reverse When Car Is Hot
Over the past few weeks, my car (2002 Golf 2.0L) has gotten really hard to shift into 1st and reverse (has crunched once or twice), but only when the car is hot, after driving it for a little while. When this happens, and I try to shift into reverse, the shifter feels really "sticky" and can get kind of stuck in the depressed position near reverse.
I bled the hydraulic system and replaced the slave cylinder, but no dice. I haven't noticed any clutch slipping. Shop wants to replace the whole clutch. Is this the right answer?
Golf/GTI VI :: Shift Knob Is Very Hard To Move When Car Is Parked
I am experiencing a very weird issue ... at least in my opinion with my DSG on my 2012 mk6 GTI. I am not sure if this is the DSG "clunk" but when parked uphill/downhill and going from P to R the shift knob is very hard to move. When switching it, it almost sounds like there is some metal grinding. This happens when the car is parked once again uphill/downhill in 99% of the time. There is some very rare instances when the DSG acts the same way when i park it on a leveled street but extremely rare once again. Should I be worried? The DSG has been a great transmission so far, no issues what so ever except VW's flash.
View 10 RepliesGolf IV / Jetta IV :: Hard To Shift When Car Warms Up On Hot Days
When it gets hot outside and the car warms up (15 mins or so of highway driving), the stick gets extremely hard to move and it doesn't go back to center when it's out of gear. So I could push it all the way left or right without putting it in a gear, and it would stay there, it wouldn't pop back to the center like it should. It becomes really annoying and difficult to drive because it gets so stiff and hard to move, what could be causing the problem? I've already adjusted the shift linkage and that didn't work.
View 3 RepliesGolf IV / Jetta IV :: 2003 - Hard To Shift Into Gears
My 03 Gli 24v manual transmission has been acting up lately. First it started to get a little difficult to shift into gears about a week ago. Then tonight i was driving through a parking lot in 2nd, and after i came to a stop i tried to put it back in to first and it would not go into gear. As i was trying to get it into 1st i could tell it was grabbing a little bit and the car was inching forward.
I got it to a parking spot and starting reading about other peoples issues, one i read said they were able to get it to move after pumping the clutch some. After trying that i was able to get it into gear and drive it to my parents. Looked at my brake fluid and its full. Took it for a test drive around the neighborhood and it was shifting fine at first then started getting a little difficult to shift again. I tried taking off in 6th and it stalled. I tried going from 1st around 3k-4k rmps to 6th and it was still driving with very little lugging. My clutch feels and is still stiff, not loose at all. I do have to go all the way to the floor with the clutch before im able to shift
Finally to my questions. Could my clutch be going bad? Could my cables need adjusting? Something I read about a pressure plate maybe?
Golf IV R32 :: Hard To Shift - In Neutral Shifter Is Centered To Right?
Decided to see if any of you fine gentleman could offer some insight into my shifting problems. OK so here it is. I have a short throw shifter and it shifts perfectly at lower RPM's ( under about 3k) anything over that and I have to somewhat force it into gear. I also noticed that when in neutral the shifter seems off centered to the right about an inch roughly. I had the R into VW for some other work recently and they said it was prob the short throw itself so I ordered a new one which should be here tm. Hopefully that will take care of this problem
View 5 RepliesGolf IV / Jetta IV :: Clutch Pedal Is Rock Solid Hard After Transmission Swap
2004 Jetta 1.8 bought mainly as a parts car w /204K miles on it. Ran and drove fine, but the tranny had no 1st gear. Tried all sorts of things other than going inside the transmission and figured it is/was a bent shift fork. Clutch worked perfectly. Had another 02J tranny from 2003 1.8, so we swapped trannys. Could not get any response from the clutch.
Start the car in neutral and it won't disengage enough to shift into gear. Start it in gear with clutch pedal in and it is obviously slipping/burning/chattering. Have bled the slave cylinder to no end, have reverse pressurized it into the reservoir , etc, etc. Made up a block off plate to go over the end of the slave actuator and when the actuator is "blocked" from moving the clutch pedal is rock solid hard. Yet, the clutch acts as if the actuator isn't extending far enough. Have swapped out the original slave cylinder with the one from the '03, no change.
Removed tranny yesterday to check the condition of the throw out bearing and pivot and Pressure plate. All appeared fine. Reinstalled tranny and same issue.
Golf IV R32 :: When Driving Hard And Speed Shift From 2nd To 3rd Transmission Grind
I have an 04' R32 with about 56k on it. Here's the problem; when I drive it hard and speed shift from 2nd to 3rd it grinds just a little. It doesn't do it when I'm just cruisen grany shifting. For awhile now I've been thinking that the synchronous from 2nd to 3rd gear was going bad, till I talked to a friend with a 20th GTI who said that the 6 speed trannies will start to do that, and there's really nothing you can do about it. Is this true that I just have to deal with it or can it be fixed?
View 12 RepliesGolf IV / Jetta IV :: 2001 VR6 Hard To Shift And Cannot Get Into Any Gear When Engine Running
01 jetta vr6 5 speed. Alright so earlier today I pulled out the driveway. (Hard) was in 1st gear around 3 or 4 grand and I stomped it. Got to 6 grand and hit 2nd. Took 2nd to 6 grand and let of around 60 mph. After that I short shifted into 3rd, 4th, then 5th. I noticed going into fith was hard. Had kinda rev match to get it. I stayed in 5th till I got to my destination roughly 4 miles. When I came back out to leave I had a hell of a time getting it into reverse. On my way home it was extremely hard to shift and now when the car is running I cant get it into any gear. This is what I did.
Car shifts fine with car off.
Car will not shift with engine running.
When started in gear with clutch depressed I can still let the clutch out and stall the car.
When starting car while in gear with the clutch NOT DEPRESSED the car jumps forward.
I can figure it out ove tried re adjusting the linkage. Nothing.
Golf/GTI VI :: Hard Time To Shift Smoothly When Engine Is Cold In The Morning
Hard time getting your manual MK6 to shift smoothly when the engine is cool after sitting overnight?? Got about 4k miles on it and I don't recall it happening when I first got it. Started maybe at 2k miles and happens every morning. It seems to only happen to me until the car warms up and then its fine, it jerks like if I was learning how to drive a manual.
View 16 Replies