Golf/GTI VI :: 2009 - When Press Throttle Cannot Go Over 1000 - 1100 RPM
I do what's written in the book (hold brake, turn ESP off, S-mode) but when i press the throttle I cannot go over 1000-1100 RPM - after a slight vibration the clutch seem to disengage and the engine goes idle. What am I doing wrong or is my version without LC?
The car is 2009 Golf 6 1.4 TSI 160hp DSG.
Golf IV R32 :: Lumpy Idle And Misfires Under Load
I've got a R32 with nearly 100K miles on it. Several days ago I was adjusting my shifter cables and am not sure if i accidentally leaned up against any sensors or their associated connectors that are in that vicinity. I took the car for a drive to feel how the shifter adjustment had turned out. I was building engine RPM from 2500-4000 RPM, I let off the acceleration pedal and felt a small and new kick as if something got loose, popped off, or backfired. Not sure what it was but my engine started to misfire in what seemed to be in several cylinders. It idles rough but the needle doesn't exceed 1000 RPM during idle. When driving calmly, there is sporadic misfire. If pushed hard to build RPM, it will misfire heavily.
I scanned the vehicle and got the following codes,
P0300
P0301
P0303
P0305
I've checked
- Every hose I can see and feel for Vacuum leaks
- Checked all my fuses
- Swapped coils from banks 1,3,5, with 2,4,6
- Disconnected, cleaned and reconnected camshaft hall sender sensors and tightened the bolts.
- Have erased the coded and the same codes are back.
Golf/GTI VI :: 2013 - Intermittent Rough Idle / Shakes As About To Stall Out - Engine Light On
I have a 2013 Golf TDI with 2070 miles on it. For around 2-3 weeks, I've noticed that it intermittently will idle rough, shakes, etc, as if it is about to stall out, but stays running and drives normal. I figured it was a typical Diesel thing and wasn't too worried about it. However, today, this happened, and I got an engine light. Yikes! I made an appointment for it but need to wait till after the 4th for it to be looked at. What's up here? Is it a regen cycle? Timing issues? Am I doomed with my Golf TDI?
View 8 RepliesGolf IV R32 :: If Rev At Start Up Car Will Idle At About 1100 RPM
Recently, my car has been having issues starting. It will start if I get a boost, but will be dead if I turn it off again. Also, while I'm driving, the airbag, ABS, and traction lifts all come on, and eventually my radio will shut off, but after a few minutes the radio will come back on and the warning lights will go off. When i first start the car it idles as it should but if I rev it will idle at about 1100 RPM. What might be causing all of this? Battery? Alternator? Or EPC?
View 7 RepliesFord 6.7L Power Stroke Diesel :: Shudder When Engine Lugged Down To 1000 - 1100 RPMs On A Hill
I purchased my 2013 F350 PSD July of 2014 and immediately noticed "the shudder" when the engine was lugged down to 1000-1100 rpms on a hill. Sounding like somewhere around the turbo belching air too. At first I was startled but learned to manually downshift to higher rpms and it will stop. Once or twice I tried accelerating out of it and it shuddered as bad as the poster who said it made the steering shudder too.
My truck has 16,000 miles and I never let the rpms drop now. So I figure I have a real problem I'm not imaging. What should I tell my dealer is the TSB or remedy ?
Golf/GTI VI :: 2010 2.5L - At Idle It Will Go Up And Down Between 1100 And 1500 RPMs
So my car started doing some weird things. at idle and only at idle it will go up and down between 1100 and 1500 rpm. No throttle input no clutch input or brake input. I do have a CEL on but when I read the code it gives me 01314 on brake electronics setting. I'm using a vchecker pro. I go into all the engine brake airbag and trans menus and do clear fault codes and this fixes it but id like to know what the actual problem is.
View 1 RepliesElantra XD (2001-06) :: Rough Idle Under 1000 RPM - Sputtering Backfire
2003 Elantra gt 90,0000 miles manual transmission. Rough idle under 1000 rpm it smooths out completely above 1000 rpm.
Also the engine makes a ticking noise from a cold start up. It stops making the ticking noise after 1500rpm or when the engine warms up.
Occasionally the car has a sputtering backfire. This happens when I park the car after being on the highway.
Replaced the plugs, wires, and the pcv valve. Dropped the oil pan and it and the oil pump pick up screen were clean.
The only check engine light to come on was for the speed sensor. It has since gone out on it's own.
Stalling - Mazda - Mazda6 :: 2006 - Run Rough And Idle At 1000 RPM?
I have a 2005 Mazda 6. When it is cold - I start the vehicle & begin to drive. When I slow down and the RPMS get around 1000 - the car begins to run really rough & try to stall. If I put my foot on the gas - I can usually prevent it from stalling. The problem disappears once the car gets warm. The dealership recalibrated the PCM based on a Mazda Alert. However, it has not corrected the issue. Looking for thoughts on what could be causing this?
View 5 RepliesStalling - Ford - Focus :: Rough Idle / Shaking When Gets Under 1000 RPMs
I have a 2008 Ford Focus - 4 Door Sedan SE 60300 miles.
I've gone to 3 mechanics now and no one can seem to figure out whats wrong with my car. Here's whats happening:
About 1 1/2 years ago I took my car to get an oil change at Jiffy Lube (Yeah never again). When I left, my car was idling funny... Silly me didn't take it right back and have them tell me what was wrong.. so I let it go, well about a month later it started idling even weirder. Basically it feels like my car is shaking when it gets under 1000 RPM and I notice my RPM dial start falling and bouncing back, acting like its going to stall, but never does. I notice a loss of power when this is happening (on speed up and just accelerating in general). All of this is random, I can't seem to put a pattern to it as to when it happens. One day I'll start it up and everything is perfect... Then I'll shut it off and restart it later, and it starts vibrating and puttering again... No signals as to if its hot/cold or wet/dry, no environmental variables seem to cause it to happen anymore than others. And there is no check engine light on, everything "looks" normal.
What I've had done to it so far is:
Air filter changed / reseated
3 oil changes (keep getting told it will work)
Throttle cleaned
Computer reset for idle sensor data rebuilding
Now I'm told that I need new engine mounts, and that could be the reason for the vibration. I'm thinking that the vibration caused the mounts to wear out, more so than the mounts being the cause. Mainly because I don't see how bad mounts could cause loss in power/bad idling.
What could be wrong?!? Really bugging me and don't want to keep throwing money at it for phantom solutions. Seems like mechanics I go to can't figure it out unless there is a check engine light on with some diagnosis code to tell them exactly whats wrong.
Ram / SRT10 :: 2001 Starts Fine Then Dies At Idle And Runs Rough On Gear Till 1000 Rpm
Starts fine. Runs fine till warmed up. Then dies at idle and runs rough on gear till 1000 rpm. Has only coded iac when unplugged. But would idle with it unplugged. I replaced it. Also got crank can code once while checking it ...
2001 dodge ram 1500 318 engine ....
Ford F-150 (2009-2014) :: Ticking Noise At 800 To 1000 RPMs / Rough Idle Leads To Engine Fail
2010 F150 ... So I have the tick noise at rpm's 800-1000 at drive through, stops, etc. So I did research on it a few months ago and saw that it might be VCT's but should be able to drive. so I drove it waiting to save money and have it go to a shop. well this past weekend while coming home from work my oil light came on the pressure dropped to zero, I was on the highway so I drove about another mile to get off highway and once I got off my truck died. I had it towed to my house and I thought I blew my motor. So I started doing research here and found that the VCT's AND cam Phaser could be bad. so I replaced my VCT on driver side put it all back together it started and loud knock was gone. then after 5 mins it was back very loud knock!
So I shut it down and took apart the passenger side once I got the valve cover off I found the problem.... The bolt that holds the cam phaser in place snapped off and was riding along the camshaft. So I took that out and extracted remaining part of bolt. inspected my camshaft and it was really messed up. so I bought new Phaser and Camshaft. the camshaft just came in today and I am trying to put it back in. but the hole for the pin in the phaser doesn't line up and I cant spin the shaft to make it line up. should I spin the cam phaser? I marked the chain and the phaser is where it should be on chain, but with that bolt snapping off could that have thrown the timing off so my mark is no good? when I lay the camshaft in place it sits perfect and if I just move the phase over 2-3 links it will all fit together. Should I do that?
Golf V R32 :: Idle At Around 1000 Rpm When Stopped At Red Light
When stopped at a stop light or sign my car will start to idle at around 1000rpm. This problem is intermittent and does not seem to change with water temperature (ie. being warmed up).
View 1 RepliesPassat (B5) :: Rough Idle / Steering Wheel Shakes And RPMs Around 500
It just started last week, only when in drive, checked vac lines, good ignition system including new plugs, its very annoying the steering wheel even shakes, what to look into, the rpm at idle is around 500. 1.8T
View 5 RepliesGolf V R32 :: Idle Starts Off Evenly At About 700 RPM Then Jump Up To About 1000
OK, I'm coming to the end of my first month of ownership. Have put on about 1,000 miles (need to drive this thing more - it's so much fun!)
Anyway, once the car is warmed up - I come to a traffic light and sit at idle. Idle starts off evenly at about 700 RPM. After a minute or so, it seems to jump up to about 1,000 RPM. Can feel it "pull" a little. After a bit of time at 1,000 RPM, it seems to drop back to 700 - but not all the time.
Mentioned it to the dealer and got a response like, "they have these things cammed". I don't think it's a cam issue. Just wondering if this is normal behavior or if there is an adjustment or part needed.
Stalling - Toyota - Rough - Celica :: 2001 - Idle Roughly / Shakes A Bit
I have a 2001 Toyota celica GT auto. It has 120k miles. I seem to have an issue that really is not causing a problem except for annoyance. After coming to a stop the car seems to exhibit the signs of stalling (car idles rough, shakes a bit) however the car never stalls. Once I start driving all is well. Now I took it to the dealer and they replaced the Idle Air Control Valve which is under the throttle body. They said it was getting stuck and due to the higher mileage possible. It was replaced and the problem is still there. The funny thing is even though the car exhibits these stalling symptoms the idle does not drop below 500 rpm (both dealer and I have verified this).
View 3 RepliesPassat (B6) :: Won't Start At First Kick And Idle Is Almost Always Lumpy - CEL Light On
Still trying to resolve this issue. I've replaced the coils and now the 6 month old NGK plugs with Bosch plugs. I bought a kit from ECU; the red coils and the Bosch plugs. Car revs smoothly no hiccups all the way on up. But sometimes the car won't start first kick, and the idle is almost always lumpy. CEL light has been on for more than several weeks. Last time I took it to the dealer to clear. It was back on the next day. 112 K (km) on car. 2009 TSI 2.0...
Parts Source will read the codes, and now there are plenty. I've looked at other threads re PCV valves and air leaks, but I don't believe they're related to the idle issue I'm having. More pronounced in the colder weather I might add.
Ford F-150 - 1997-2003 :: 4.6 Lumpy Idle When In Gear
Recently I just purchased a 1998 F-250 (light duty) with 11X,XXX miles on it. Up until today, it was running perfectly. However, today it started idling rough whenever I was at a light. This was only when I was stopped, in gear, with my foot on the brake. In neutral or park it didn't do it, and it stopped as soon as I gave it a little gas. No CEL either. I've looked around, and saw that it might just be "feature" of the 4.6. I also have seen to clean the MAF, but wouldn't that also give a rough idle when in park/neutral? Same with replacing the coil pack.
View 1 RepliesPassat (B5) :: Brake Pedal Really Spongy / No Power And Lumpy Idle
Drove the lady's car out on some errands today and ran into a problem on our drive home. Car was pinging really bad (low rpms in 1st and second) and car seemed as if it couldn't get out of its own way. Was driving for some time on the freeway (after a blistering 0-60 time of 20 seconds ), and noticed that the brake pedal was really spongy (felt like a mk1 when you try to brake with the car off). Found that the e-brake handle was up (negligibly up (perhaps 1mm raised)). Didn't have power brakes at all and had to use a lot of engine braking to slow the car off of the freeway.
Rear of the car smells like copper (wet pennies) and found that the brake reservoir is cracked (but fluid still at max level). Also noticed that as of late, when the car is at a stop (sometimes in gear, and sometimes in neutral) the car will rock/bump a little almost as if someone were giving it a bumper kiss with their car.
Passat (B5) :: Lumpy Idle / Smooth Acceleration And Misfires - CPS Error
I am trying to track down a problem for a friend with a 2001 Passat, 1.8L. The car has 150k and had a timing belt about 50k ago. About 3 weeks ago, it started misfiring badly on idle. In gear driving around, it purrs like a kitten. I scanned for codes and got:
Address 01: Engine
Controller: 4B0 906 018 CL
Component: 1.8L R4/5VT G 0001
Coding: 16551
9 Faults Found:
[Code] ....
At first I thought it might be a vacuum leak, but it looks like when he took it in 2 weeks ago they replaced all the vacuum hoses. It is unclear when he last had sparks and coils. I understand the likely culprits are:
sparks
coils
ICM
I am hesitant to blame sparks/coils if he is getting misfires on all 4 cyl. It seems like they might have screwed up the timing belt install given the camshaft sensor error, but he's been running for 50k miles since the change, and this idle issue just appeared recently.