Passat (B5) :: Lumpy Idle / Smooth Acceleration And Misfires - CPS Error
I am trying to track down a problem for a friend with a 2001 Passat, 1.8L. The car has 150k and had a timing belt about 50k ago. About 3 weeks ago, it started misfiring badly on idle. In gear driving around, it purrs like a kitten. I scanned for codes and got:
Address 01: Engine
Controller: 4B0 906 018 CL
Component: 1.8L R4/5VT G 0001
Coding: 16551
9 Faults Found:
[Code] ....
At first I thought it might be a vacuum leak, but it looks like when he took it in 2 weeks ago they replaced all the vacuum hoses. It is unclear when he last had sparks and coils. I understand the likely culprits are:
sparks
coils
ICM
I am hesitant to blame sparks/coils if he is getting misfires on all 4 cyl. It seems like they might have screwed up the timing belt install given the camshaft sensor error, but he's been running for 50k miles since the change, and this idle issue just appeared recently.
Golf V R32 :: VR6 Rough / Lumpy Idle - Whole Car Shakes When Rev It To 1000 To 1100 Rpm
Audi A3 3.2 owner here from Fortitude and have rough / lumpy idle issues? While at a stop in neutral w/a cold or warm engine, it seems a little rougher than one would expect. If you rev it to 1000-1100 rpm the whole car shakes.
Engine Mounts worn?
APR Software causation?
Cam Followers or faulty coils?
Do I need a heavier duty front and top engine mount?
Wondering if CAI and Exhaust along w/ the APR ECU tune is causing it or if I'm just being paranoid.
Passat (B6) :: Won't Start At First Kick And Idle Is Almost Always Lumpy - CEL Light On
Still trying to resolve this issue. I've replaced the coils and now the 6 month old NGK plugs with Bosch plugs. I bought a kit from ECU; the red coils and the Bosch plugs. Car revs smoothly no hiccups all the way on up. But sometimes the car won't start first kick, and the idle is almost always lumpy. CEL light has been on for more than several weeks. Last time I took it to the dealer to clear. It was back on the next day. 112 K (km) on car. 2009 TSI 2.0...
Parts Source will read the codes, and now there are plenty. I've looked at other threads re PCV valves and air leaks, but I don't believe they're related to the idle issue I'm having. More pronounced in the colder weather I might add.
Ford F-150 - 1997-2003 :: 4.6 Lumpy Idle When In Gear
Recently I just purchased a 1998 F-250 (light duty) with 11X,XXX miles on it. Up until today, it was running perfectly. However, today it started idling rough whenever I was at a light. This was only when I was stopped, in gear, with my foot on the brake. In neutral or park it didn't do it, and it stopped as soon as I gave it a little gas. No CEL either. I've looked around, and saw that it might just be "feature" of the 4.6. I also have seen to clean the MAF, but wouldn't that also give a rough idle when in park/neutral? Same with replacing the coil pack.
View 1 RepliesGolf V R32 :: Persistent Misfires At Idle
In the last few months, I've been having misfires at idle. I didn't realize at first what the vibration was, since I had cams installed over the summer and had my flywheel replaced a couple of weeks ago. I have replaced the plugs and coil packs and for a couple of days, it ran fine. Tonight, they started up again, mostly in a single cylinder. I swapped out coil packs - no change. Switched plugs between two cylinders - the misfire followed the plug. Swapped in an old plug - things improved, misfires went from 2-3 per second to maybe one every 5-10 seconds. Few to no misfires when revs go up. My battery is 5 years old, could that be an issue? Wire harnesses - do they go bad?
View 24 RepliesPassat (B5) :: Brake Pedal Really Spongy / No Power And Lumpy Idle
Drove the lady's car out on some errands today and ran into a problem on our drive home. Car was pinging really bad (low rpms in 1st and second) and car seemed as if it couldn't get out of its own way. Was driving for some time on the freeway (after a blistering 0-60 time of 20 seconds ), and noticed that the brake pedal was really spongy (felt like a mk1 when you try to brake with the car off). Found that the e-brake handle was up (negligibly up (perhaps 1mm raised)). Didn't have power brakes at all and had to use a lot of engine braking to slow the car off of the freeway.
Rear of the car smells like copper (wet pennies) and found that the brake reservoir is cracked (but fluid still at max level). Also noticed that as of late, when the car is at a stop (sometimes in gear, and sometimes in neutral) the car will rock/bump a little almost as if someone were giving it a bumper kiss with their car.
Ford 6.0L Power Stroke Diesel :: 2005 - Intermittent Lumpy Idle When Hot
My 2005 Excursion, at 198K miles has become more of a 'hangar queen' in that I only use it for big jobs. I've kept it for towing/hauling and making long highway runs with more than 4 people.
The truck, 99.8% of the time, runs super. It pulls like a locomotive and gets decent fuel economy (17 mpg running 75 mph empty). I've got the 'blue spring', EGR delete, ARP headstuds, 4" MBRP, Banks intercooler, and run my SCT tuner all the time on "8000 lb tow".
But...there is this weird intermittent problem. It appears to only happen when it is warmed up and driving around town. Sometimes, when I pull up to a light, with my foot on the brake, the engine will sort of go into a 'lumpy race idle' and you have to clamp down on the brake pedal to keep it from lurching into the guy in front of you. Other times, it just runs rough and idles 'lumpy'. It has only died maybe 2 times when acting up. Often, the symptoms disappear on their own and don't come back. If I turn off the engine and re-start (to keep from scaring people at the bank drive-through) it usually runs fine after restart.
I've got an EDGE CTS monitor so I've been trying to find out from that what is going on. I can't seem to catch the parameter that might tell me. My local 'indy' shop can't find any codes thrown. The truck had new alternator, batteries, and starter motor installed in January this year. These symptoms have been going on for several years. Recently, they seem to occur more often.
I've searched on this site a few times, but with no definite 'hit'. I'll admit that I'm a big out of the jargon. I keep thinking this is related to FICM, but everyone seems to say the FICM would manifest as a cold start problem. I do know the FICM sits right on top of the drivers side valve cover. It has got to get hot.
FICM?
Injectors?
How do I kill this one strange problem?
Golf IV / Jetta IV :: 2005 GTI 1.8t - Rough Idle And Misfires
2005 gti 1.8t having really rough idle and misfires at idle fine while driving pulling codes:
P0300
P0301
P0302
P0304
Unplugged MAF and didn't make a difference...
Golf IV / Jetta IV :: Rough Start And Idle But No Misfires
I have an 03 vr6. I'm getting codes p0300, 0303, and 0304. I changed the plugs and the coils and still has changed nothing. In the morning when I first go to start the car it has a rough start and idles rough. But after letting it warm up it is fine. It drives perfectly fine, no misfires. None of this started happening until the car ran hot a few weeks ago. Did a compression test and everything came up fine. So would could my issue be? I'm at a loss here. I was thinking fuel issue but if it was a fuel issue, wouldn't it run rough all the time?
View 15 RepliesGolf IV / Jetta IV :: Multiple Random Misfires In All 4 Cylinders Came Up / Idle And Boost
I have a mk4 1.8t Gti. Recently I have been having issues with idle and boost. I read the codes and multiple random misfires in all 4 cylinders came up, idle control and the crank, knock, and o2 sensor came up. Shows that system is running to lean as well. I changed the spark plugs and wires, check the coil packs they where done about 1k miles so I expect them to be perfectly fine. When I clear the codes it idles below 9-8k rpms. I also noticed the breather hose coming out of the valve cover into the EGT has a hole melted into it, could this cause any of my issues?
View 2 RepliesFord - Escape :: 2001 - Engine Misfires Under High Load And Low RPM
I have an 2001 Ford Escape V6 3.0, about 130,000 miles. When the engine gets under high load and low RPM, before downshifting, it will shudder (misfire?). Local shop couldn't reproduce it, but they thought it might have to do with slightly cracked vaccume hose, which they gouged me to replace. No improvement. Next they wanted $700 to replace Valve Cover Gaskets. I decided to become a mechanic and learn how to do that one myself. Sure enough, there was a little oil dripping onto one plug. I replaced the gaskets and all 6 spark plugs successfully. Still didn't fix the problem though.
Symptoms will occur reliably when driving at 45-50 MPH with the transmission in overdrive (1500 RPM), and I begin a slight incline. The vehicle will kind of chug forward (feels like sporatic misfires) in overdrive, getting down to 1200 RPM before deciding to downshift. Generally, I can just give a little more gas to force downshift and avoid the nasty-feeling misfires. Some days, however, it is much worse, and will misfire at idle, and make me feel like I have to treat the gas as an on/off switch to keep the engine from dying. (It has never actually died.)
During a really bad day, I got a flashing check engine light. I did not check codes in time - they've all cleared.
I now have an ODB2 reader logging real-time data. All I can do is prove the conditions that cause the symptom: high engine load at low RPM is the recipe. Nothing seems to show a cause... I may just not know what I'm looking at :-/ . I haven't monitored long enough to record a 'bad' day.
I've read about ignition coil issues on this engine, and weather might explain why this is worse some times than others. However, I wouldn't expect that to be load dependant.
Most of the time it feels like the transmission just isn't shifting when it's supposed to, but on the bad days it seems more than transmission related. When stopped at a light in Drive, this can still occur.
Ford F-150 (2004-2008) :: 2005 - Strong Misfires Under Load
I have a 2005 F150 with 5.4 and have been having increasing random misfires. This is MUCH more pronounced when the engine is warm, and I can certainly count on it to happen when under load, either accelerating or whatever. If I am forced to remain stopped for any extended period of time, such as waiting in line at a drive through, then start to drive again, the problem seems to increase exponentially, and is most pronounced in the 1300 - 1900 RPM range. If I take the overdrive off in order to put the rev's above 2000, it eases the problem, but does not eliminate it. The issue is much LESS pronounced when first starting driving, it seems to be most prominent only after it warms up.
So far, the only codes I have ever seen is random misfires, and only once has the code gone solid in the ECM. Usually, if I back off load for a minute, it clears up on it's own and the flashing code light clears .... If I attempt to accelerate hard, even when cold, the misfires get really bad and I can always expect a hard code soon afterwards ...... needless to say, I have no real power at any time, and my fuel efficiency is beyond bad (best I can get is about 11 mpg) ....
Suburban :: 1999 - While Driving After Engine Warm-up Misfires On Cylinder 2 Under Slight Load
1999 Suburban 5.7L Vortec
Symptoms: While driving after engine warm-up the engine misfires on cylinder 2 under slight load (basically whenever maintaining speed, and slight acceleration) between 1500-3000 rpm's. Backfires through exhaust when this is happening. Misfire counts on Cyl. 2 collect rapidly and only a few on Cyl. 1 but no P0301.
History: Purchased vehicle with a blown engine (intake gasket leaked coolant into engine and was hydro-locked) with the intention of using it to pull a boat or camper but never did buy either one. Replaced the engine with a new Goodwrench engine and rebuilt the tranny figuring I would drive it till the body rusted off of it. I honestly never felt that the truck ran as strong as it should have with a brand new engine but just attributed it to being as big as a cruise ship. A couple of years later started receiving multiple codes (don't remember what they were at this time) found the distributor very corroded inside due to the ear on the distributor being broken off.
Replaced the distributor, cap,rotor,plugs and wires and fixed it. About a year later, only in the summer I would start to receive the P0302 sometimes, would not happen in the winter. Did the usual plug swap, wire swap, checked spark to rule out ignition with no change. After a while the catalytic converter failed (big surprise with a missing engine) and replaced it as well as both O2 sensors on the rear bank and one on the front bank. P0302 did not change. Last year the fuel pump failed so I replaced it. This April I took the truck on a road trip to visit relatives, about 80 miles out it started backfiring through the exhaust whenever I got over 70 mph and the CEL would flash. Finished the trip babying it the whole way but now it does this all the time when warm.
Repair attempts:
* Distributor, cap, rotor, wires, plugs. (Due to distributor failure mentioned above.)
* Fuel pump and filter. (Due to pump failure mentioned above.)
* Upgraded fuel injection spider. (Because of GM bulletin regarding misfires and multiple failures found on the internet.)
* Repeated valve and fuel system cleanings. (Grasping at straws.)
* Removed rear bank cylinder head and sent to machine shop, All checked good. (After ruling out ignition and fuel figured it had to mechanical. Compression was good, cylinder leak down test was good. The problem seems to be temperature related so thought maybe the exhaust guide was mis-manufactured too tight causing it to drag when warmed up.)
* Crank sensor with a used one from a u-pull it place, I got too much money wrapped up in this. (Found a reference to this repairing a similar problem on another vehicle.)
One final note: After replacing the fuel injection spider the truck ran extremely well, this only lasted a few days and the problem came back. After replacing the crank sensor the truck again ran extremely well, but only for 1-2 days. What is the connection between the injection spider and the cranks sensor? The only other thing that I can think of that would create a misfire on one cylinder only is the PCM but that gets misdiagnosed so much that I don't want to jump to it unless all other options have been checked out.
Golf V R32 :: Not Blowing Warm Air At Idle But Heat Comes Back Under Load?
My car is not blowing warm air at idle when warmed up. When under load driving the heat comes back then chills down when stopped at a light or traffic. I did a coolant flush by fill and gravity drain earlier this summer and have had zero issues with overheating or anything else. Could there be air in the heater core or is my water pump or thermostat failing?
View 4 RepliesGolf IV / Jetta IV :: Knock On Biting Point Idle And Pull Away Under Load
I can't figure if it's a TB issue as I've just had it replaced or a mount problem. I only get the knock on biting point idle and pull away under load. This noise is driving me insane.
View 2 RepliesPassat (B6) :: Shakes At Idle - Multiple Random Misfires
So I took a trip from Dallas to Florida, and on the way back my check engine light came on. The car shakes at idle, almost like it wants to take off. I drove it back to Dallas like that since the car runs normal on the high way. I got it scanned at autozone and the code said it had multiple random misfires. I'll be taking to the dealer in the morning, but what it could be? The car jumped over 50K during the trip hopefully the dealer will be nice and cover it.
View 4 RepliesPassat (B5) :: 1999 Needs Some Throttle To Start / Low Idle Speed And Misfires
When I start my 1999 1.8 petrol passat it needs some throttle to start, low idle speed, misfires, drop in idle, so boot the throtle full - still no pick up and sits on 1000 rpm busy backfiring away! It started after fitting a new windscreen wiper motor, battery was disconnected but went back ok, all other electrics work and no warning on the dash. Didn't touch anything in the engine bay nor were there any issues before I changed the wiper motor.
View 12 RepliesDodge - Dart :: 1969 Misfires / Tremble And Shuts Off When At Idle
I recently purchased a 1969 dodge dart, with the 225 inline 6. I have done the usual repairs (fluid changes, spark plugs and wires, fuel pump and line, thermostat, and even carburetor and distributor). The car starts and drives alright except when at idle such as red lights where it begins to tremble and shuts off. I have to start it again and begin to accelerate it while idling to keep it from giving out. I fixed the timing and switched to electrical distributor but the problem has persisted.
View 7 RepliesTiguan :: Random Cylinder Misfires On All Cylinders With Rough Idle
I have 11 tiguan 2.0T. When I start it up is runs rough below 1200 rpm. The check engine light starts flashing. The codes are all 4 cylinders for random cylinder misfire. When I go drive it around the roughness calms down but doesn't go away and the idle will start jumping up and down. It goes to 1500 back to 800. Then 1700 back to 800. It had even hit 2400 once. I have changed the pcv about 2 months ago. I checked it and it looks fine. One place said maf. I cleaned it and no change. Running out of options.
View 2 Replies