Ford F-150 (2004-2008) :: 2005 F150 5.4L Hesitation Under Load
How's it going? I have a 2005 F150 with the 5.4L V8. It has 70,000 miles on it and until yesterday and has been a great truck. While driving in traffic yesterday the truck started running rough and hesitating. It through two codes - misfire cylinder 5 and misfire cylinder 6.
In response, I purchased two new coils and 8 new autolite plugs. The plug installation went smoothly and the coils all went on without incident. However, this didn't fix the problem!
The next day I found that cylinders 5, 6, 7, and 8 were all having issues. At this point I also had an "O2 stuck lean" code so I pulled the plugs and found all four brand new plugs fouled and smelling like gas and an ehaust that smelled like raw fuel. This led me to replace the O2 sensor on the drivers side. With the new O2 my lean code disappeared but I still had a rough idle.
Further troubleshooting found that injector 6 was stuck open (which presumably fouled my O2 causing it to read lean and dump fuel thus fouling all the plugs on one side). I replaced the injector and the rough idle disappeared and all seemed really well as the truck idled in my driveway.
However, as soon as I hit the road I noticed a major hesitation. The motor is also noticeably louder and has a very hard time accelerating. I'm thinking that I've plugged up my cat by dumping so much fuel in to it and the hesitation is caused by a lack of breathing - does this sound possible? How would I confirm this without replacing the cat? Anything else I should look for? I'm fairly confident I have combustion in all 8 cylinders now so I'm leaning towards intake/exhaust issues.
Ford F-150 (2004-2008) :: 2005 V8 - OD Blew Out While Carrying The Load
At work we have an '05 F150 stx 4x4 auto v8, I'm wondering what Trans it has. 4100r?
Reason I'm asking is the OD blew out while carrying a load the other day and since everyone else in the shop are Chevy/Chrysler people, I got unloaded with making the decision of what to do. New or reman trans? Try and fix it?
Ford F-150 (2004-2008) :: 2005 - Hesitation Under Load - Combustion In All 8 Cylinders - Cat?
I have a 2005 F150 with the 5.4L V8. It has 70,000 miles on it and until yesterday and has been a great truck. While driving in traffic yesterday the truck started running rough and hesitating. It through two codes - misfire cylinder 5 and misfire cylinder 6.
In response, I purchased two new coils and 8 new autolite plugs. The plug installation went smoothly and the coils all went on without incident. However, this didn't fix the problem!
The next day I found that cylinders 5, 6, 7, and 8 were all having issues. At this point I also had an "O2 stuck lean" code so I pulled the plugs and found all four brand new plugs fouled and smelling like gas and an exhaust that smelled like raw fuel. This led me to replace the O2 sensor on the drivers side. With the new O2 my lean code disappeared but I still had a rough idle.
Further troubleshooting found that injector 6 was stuck open (which presumably fouled my O2 causing it to read lean and dump fuel thus fouling all the plugs on one side). I replaced the injector and the rough idle disappeared and all seemed really well as the truck idled in my driveway.
However, as soon as I hit the road I noticed a major hesitation. The motor is also noticeably louder and has a very hard time accelerating. I'm thinking that I've plugged up my cat by dumping so much fuel in to it and the hesitation is caused by a lack of breathing - does this sound possible? How would I confirm this without replacing the cat? Anything else I should look for? I'm fairly confident I have combustion in all 8 cylinders now so I'm leaning towards intake/exhaust issues.
Ford - Escape :: 2001 - Engine Misfires Under High Load And Low RPM
I have an 2001 Ford Escape V6 3.0, about 130,000 miles. When the engine gets under high load and low RPM, before downshifting, it will shudder (misfire?). Local shop couldn't reproduce it, but they thought it might have to do with slightly cracked vaccume hose, which they gouged me to replace. No improvement. Next they wanted $700 to replace Valve Cover Gaskets. I decided to become a mechanic and learn how to do that one myself. Sure enough, there was a little oil dripping onto one plug. I replaced the gaskets and all 6 spark plugs successfully. Still didn't fix the problem though.
Symptoms will occur reliably when driving at 45-50 MPH with the transmission in overdrive (1500 RPM), and I begin a slight incline. The vehicle will kind of chug forward (feels like sporatic misfires) in overdrive, getting down to 1200 RPM before deciding to downshift. Generally, I can just give a little more gas to force downshift and avoid the nasty-feeling misfires. Some days, however, it is much worse, and will misfire at idle, and make me feel like I have to treat the gas as an on/off switch to keep the engine from dying. (It has never actually died.)
During a really bad day, I got a flashing check engine light. I did not check codes in time - they've all cleared.
I now have an ODB2 reader logging real-time data. All I can do is prove the conditions that cause the symptom: high engine load at low RPM is the recipe. Nothing seems to show a cause... I may just not know what I'm looking at :-/ . I haven't monitored long enough to record a 'bad' day.
I've read about ignition coil issues on this engine, and weather might explain why this is worse some times than others. However, I wouldn't expect that to be load dependant.
Most of the time it feels like the transmission just isn't shifting when it's supposed to, but on the bad days it seems more than transmission related. When stopped at a light in Drive, this can still occur.
Ford F-150 (2004-2008) :: Random Misfires In Almost Every Cylinder
I have an 05 Lariat with 145k miles on it. About a month ago I had a misfire code on one cylinder. Since then it's gone from once every couple of days, various cylinders. To now every day. I've had to continue driving it but the last few days it's gotten bad and I hope I didn't do any more damage(cats) but I didn't have a whole lot of choice. I've read every thread I can find and haven't found an exact match. It seems to be worse first thing in the morning, it will be down on power for a few seconds then clear up. It may not return for another 10 or 15 minutes and then cough a little and clear up.
Sometimes it will start at the beginning of a hill and not clear up until I'm back on flat, sometimes it will lose power at the top. There is zero predictability to it. I have had codes on almost every cylinder, but no single one has dominated the problem. Twice when it has been real bad I have also gotten a lean code 0174. It had new Motorcraft plugs 25000 miles ago and has run fine until recently. The ticking isn't too bad but I think I'm going to try thicker oil for the summer. It's been a while since I did the fuel filter and since it probably isn't a bad idea I'm going to do that today.
Golf IV R32 :: Lumpy Idle And Misfires Under Load
I've got a R32 with nearly 100K miles on it. Several days ago I was adjusting my shifter cables and am not sure if i accidentally leaned up against any sensors or their associated connectors that are in that vicinity. I took the car for a drive to feel how the shifter adjustment had turned out. I was building engine RPM from 2500-4000 RPM, I let off the acceleration pedal and felt a small and new kick as if something got loose, popped off, or backfired. Not sure what it was but my engine started to misfire in what seemed to be in several cylinders. It idles rough but the needle doesn't exceed 1000 RPM during idle. When driving calmly, there is sporadic misfire. If pushed hard to build RPM, it will misfire heavily.
I scanned the vehicle and got the following codes,
P0300
P0301
P0303
P0305
I've checked
- Every hose I can see and feel for Vacuum leaks
- Checked all my fuses
- Swapped coils from banks 1,3,5, with 2,4,6
- Disconnected, cleaned and reconnected camshaft hall sender sensors and tightened the bolts.
- Have erased the coded and the same codes are back.
Ford F-150 (2004-2008) :: Oil Leak Under Load Only?
Have a friend and looking at his truck for him. He was towing a boat and climbing a steep grade hill. As he described it, it felt like he lost all power. Did manage to get it to the top of the hill and stopped to check it out.
Noticed the under of the truck dripping oil. Checked the motor oil and none on the stick. Put 4 quarts in the motor, started it back up and oil pressure is good and motor sounds fine.
The strange thing is the motor is dry. Can not find where the oil leaked out. All the oil is located on the transmission and transfer case. I'm not too familiar with these Triton 5.4's but where could that oil possibly have come from? I'll re-look this morning.
Also, with oil in motor, and it is idling, there is no oil leak or drip anywhere. Is there a pressure regulator in this oil system and the load he was exerting cause it to release?
Ford F-150 (2004-2008) :: Hiss When Engine Was Under Load
I have a 2004 f150 lariat crew cab 4x4 with the 5.4 3 valve. It now has 113 000 miles. Since i got it at 85 000 miles its had a hiss when the engine was under load. So like light acceleration or driving into wind. The guy i bought it from said that it had a manifold leak so that's what i figured it was. I got the manifold fixed and it still hisses. There are no check engine lights. It almost feels like my engine lags when it starts hissing. It sounds like its coming from right on the other side of the fire wall. What it could be?
View 3 RepliesFord F-150 (2004-2008) :: Truck Has Miss Under Load
I have a 2004 150 with 165,000 miles I sometimes pull a 5 by 8 trailer. when pulling trailer in overdrive and excelorating the engone will cough several times. I took it to a mechanic and he told me that there was nothing he could do that I needed a new engine. I can pull trailer out of overdrive with no problem. don't undrstand why I need new engine....
View 3 RepliesFord F-150 (2004-2008) :: No Disc And Load Error
I have a Lariat 4x4 supercrew cab with a CD 6 disc changer head unit. Error message. No Disc, and Load Error. Will not eject any of the 6 loaded CDs. Pulled/reset fuse. No luck. Banged on dash while trying to eject any of the loaded CDs.. no luck. Unit cycles when first starting the engine. Radio works fine. Unit locked up....Ford Mx tech says the solenoid that holds the CD is frozen in position and will not release.
View 3 RepliesFord F-150 (2004-2008) :: Rattling Sound Happens Under Load When On Gas?
Hard to describe sound, but it only happens under load. It happens at any speed, but more predominently at higher speeds. When I lift off the gas it stops. I can keep it going up hill since I'm maintaining speed rather than accelerating over the limit. The other day I heard another F150 beside me making the same noise going up a hill.
View 14 RepliesFord F-150 (2004-2008) :: Spark Knock Under Load?
I have a 04 5.4 w/ a whipple supercharger. truck has 104k miles. Has a misfire in cyl 4 (p0304, p0316) And spark knock.. I've changed the plugs, coil on cyl 4, fuel filter, and today the o2 sensor(pass side upper, bank 2??). I've ran tecron injector cleaner threw it, and always used Chevron 90 octane. (highest in Alaska)
The noise only happens when under load, or accelerating with more then half the throttle. doesn't happen when i slowly get up to speed. What I could do next? About to take it to the dealer to run a full diagnostic test on it.. Also, does not hesitate or bog. drives normal just with that noise
Ford F-150 (2004-2008) :: Occasional Hard Start / Engine Cranks Strong But Fails To Catch And Then Sputters
My truck's been having an occasional hard start, meaning the engine cranks strong but it fails to catch and then sputters. The 2nd start attempt usually fires up with no issues and then runs perfectly otherwise.
MPG's haven't changed, fuel filter was changed 15K ago. Air filter is clean. Plugs were changed about 10K ago. I always use Shell/Chevron gas. MAF sensor looked clean when I took it out so I didn't do anything to it.
This is starting to happen more frequently, maybe once every few weeks and I get a feeling it's the start of something. I've found myself waiting a few seconds for the fuel pressure gauge to come up before turning the key to start reliably. In the past, I could simply flick the key and it fires up the first time.
I see posts talking about the fuel pump module above the spare tire. What are symptoms of that going bad? Any pending codes that might be stored?
I'm about to get myself a scanner since I need one sooner or later. Which specific PID's to check while debugging this?
Ford F-150 (2004-2008) :: 2006 - Backfire Under Load During Acceleration
I have a 2006 ford f 150 with a 5.4 Triton 3v engine and every time I floor it and the engine reaches 3000 rpms the truck backfires and looses power. Sometimes it wont pass 3000 rpm it just stays there and backfire and have no power. Sometimes the check engine light flashes...... I took the coils off and looked at them and they all looked pretty clean. Also the truck idles rough and sometimes when it cruising at low rpms, and I give it a little gas the truck will randomly misfire and shake hard. also the engine sounds like a diesel engine........ What might be wrong.
View 6 RepliesFord F-150 (2004-2008) :: Misfire Under Load At 40 - 60 MPH While In OD Or At Higher RPMs At WOT
I have a 2006 Ford F150, king ranch, 4x4, super crew 135k miles. I bought the truck and shortly after noticed the miss under a load at 40-60 mph while in OD, or at higher RPMs at WOT, but never a CEL. Well 3 months went by and I couldn't take it anymore so with lots of research I decided to change the plugs. Ran seafoam through 2 tanks of fuel prior to this job to break up the carbon in hopes of none of the plugs breaking.
All 8 plugs came out with no issue and I replaced them with the Motocraft SP 515s (old ones were very nasty and brittle, most likely the original). I put copper anti seize on the end that goes through the channel in the head, however none got on the end near the electrode, and also on the threads. Put it all back together and it had the worse misfire an pretty much not drivable....flashing CEL and codes p0308, p0355, p0356. So I decided to buy 8 new coils as well, got all 8 of them on and now the truck is drivable but the miss is still there (no CEL).
Feels like maybe just one cylinder and I believe I got it pin pointed to cylinder 8. I put a vacuum gauge on it and unplugged the injectors 1 at a time and cylinder 8 is the only one that there is no change while unplugged. So I switched out the coil thinking maybe I got a bad one, still does it. My COP electrical plug has 12v Constant and also confirmed with an led it is getting signal. The injector is ticking or pulsing as i confirmed with a mechanic stethoscope. What am I missing????? Today when I get off I plan pulling the spark plug, checking for carbon tracking, check compression, check actual visual spark, and pull and clean the injector.
Ford F-150 (2004-2008) :: Jerking Under Load Like Engine Is Cutting Out
I'll try to explain what the truck is doing best I can. I'm not sure if it's the engine or tranny. When you lug the truck on a hill or put a load behind it and lug it the truck jerks like the engine is cutting out or the tranny is jerking, I can't tell which. You can drive it all day long on a flat road or small hills and you can't make it do it. It does it worse going up a hill with a load behind it. You can lug the truck on a steep hill let off the accelerator and mash it back down and it will do it almost every time. I've tried overriding the overdrive and it still does it. If you keep the rpms above 2000 up a hill it won't do it. I've had it checked by a transmission shop and they couldn't make the truck do it. Also it doesn't throw any codes or put the check engine light on when this happens. 2007 F150 supercrew 5.4 auto, with 88,000 miles.
View 12 RepliesFord F-150 (2004-2008) :: Rough Misfire Under Moderate Load
I have an 05 F150 with the 3v 5.4 with 170k on it. Last fall we changed the timing chains, cam phasers (aftermarket), plugs, coils (OEM), VVT solenoids (OEM), Cam Position sensors (OEM) and swapped in a GT500 oil pump. Recently under moderate load (fairly heavy acceleration onto the freeway, pulling a large camper) I get a pretty rough misfire. Tonight I pulled the codes and it was Cylinder 5 misfire. In the past I have also had Bank 2 Over-Retarded code. What are the next things to verify and check? I plan to clean the throttle body and change fuel filter but I'm not sure either of those would cause the misfire code?
View 3 RepliesFord F-150 (2004-2008) :: Ticking And Hesitation / Stumble A Bit Between 40 - 55 MPH Under Load
First, a little background on my truck. 2007 with 5.4, 122000 miles, oil changes with 5-20 Motorcraft and Motorcraft filters, plugs done by dealer 40000 miles ago. The truck has developed a ticking noise, kind of like a lifter (I know these engines don't have lifters) that is most noticeable from the side of the truck near wheel. ticking speeds up with the rpm. Also around same time, between 40-55 under load there is a bit of a stumble, but I can gas thru it. I'm guessing these are related. I'm thinking spark plugs again, but shouldn't I get more than 40000 out of them? I might just take it in, since I've got oil leak somewhere around back of the oil pan, but figured maybe might get some clues first. Also, no CEL.
View 4 RepliesSuburban :: 1999 - While Driving After Engine Warm-up Misfires On Cylinder 2 Under Slight Load
1999 Suburban 5.7L Vortec
Symptoms: While driving after engine warm-up the engine misfires on cylinder 2 under slight load (basically whenever maintaining speed, and slight acceleration) between 1500-3000 rpm's. Backfires through exhaust when this is happening. Misfire counts on Cyl. 2 collect rapidly and only a few on Cyl. 1 but no P0301.
History: Purchased vehicle with a blown engine (intake gasket leaked coolant into engine and was hydro-locked) with the intention of using it to pull a boat or camper but never did buy either one. Replaced the engine with a new Goodwrench engine and rebuilt the tranny figuring I would drive it till the body rusted off of it. I honestly never felt that the truck ran as strong as it should have with a brand new engine but just attributed it to being as big as a cruise ship. A couple of years later started receiving multiple codes (don't remember what they were at this time) found the distributor very corroded inside due to the ear on the distributor being broken off.
Replaced the distributor, cap,rotor,plugs and wires and fixed it. About a year later, only in the summer I would start to receive the P0302 sometimes, would not happen in the winter. Did the usual plug swap, wire swap, checked spark to rule out ignition with no change. After a while the catalytic converter failed (big surprise with a missing engine) and replaced it as well as both O2 sensors on the rear bank and one on the front bank. P0302 did not change. Last year the fuel pump failed so I replaced it. This April I took the truck on a road trip to visit relatives, about 80 miles out it started backfiring through the exhaust whenever I got over 70 mph and the CEL would flash. Finished the trip babying it the whole way but now it does this all the time when warm.
Repair attempts:
* Distributor, cap, rotor, wires, plugs. (Due to distributor failure mentioned above.)
* Fuel pump and filter. (Due to pump failure mentioned above.)
* Upgraded fuel injection spider. (Because of GM bulletin regarding misfires and multiple failures found on the internet.)
* Repeated valve and fuel system cleanings. (Grasping at straws.)
* Removed rear bank cylinder head and sent to machine shop, All checked good. (After ruling out ignition and fuel figured it had to mechanical. Compression was good, cylinder leak down test was good. The problem seems to be temperature related so thought maybe the exhaust guide was mis-manufactured too tight causing it to drag when warmed up.)
* Crank sensor with a used one from a u-pull it place, I got too much money wrapped up in this. (Found a reference to this repairing a similar problem on another vehicle.)
One final note: After replacing the fuel injection spider the truck ran extremely well, this only lasted a few days and the problem came back. After replacing the crank sensor the truck again ran extremely well, but only for 1-2 days. What is the connection between the injection spider and the cranks sensor? The only other thing that I can think of that would create a misfire on one cylinder only is the PCM but that gets misdiagnosed so much that I don't want to jump to it unless all other options have been checked out.