Golf IV R32 :: P1347 / P0011 And P1143 Codes - Oil In Both Camshaft Position Sensors
Throwing codes here.... been seeing the P1347 consistently with the P0011 and P1143 intermittent.
I have checked the resistance of the camshaft adjustment valve resistance and found them to both be around 9 Ohm (spec is 10-18 Ohm).
I checked the voltage to both camshaft position sensors and they are in spec at 4.9 Volts
I swapped the camshaft position sensors to see if the code would follow the sensor but it did not so it is directly related to the intake camshaft.
It is looking like there is a timing issue either related to the adjustment valves going or possibly some contamination preventing them from working properly. They are both out of spec in terms of resistance which is odd that they would both go at the same time but possible.
The oil inside the camshaft position sensors is no good I cleaned it all out when I swapped the sensors but no change. These will have to be replaced.
Car has 125k on it so it could be due for timing chains but I want to rule out anything else first.
Golf IV / Jetta IV :: Code P1340 - Cam / Crankshaft Sensor Out Of Sequence
So I started up my 12v VR6 the other morning and it sounded like a Subie. Threw the awful code P1340: cam/crankshaft sensor out of sequence, and took it to the shop. I'm being charged $1900 for servicing the timing chains, only. Doesn't include water pump and clutch like every other shop does. Reason for this is because in Montana, no one works on these cars. So I this is my only route. I had to choose this small euro repair shop or the VW dealer.
But, they just recently called me and told me I need to get the timing gears changed or whatever? They want to charge an additional $600 or so to do that. Are these gears a real problem? or are they just trying to F me. I mean, $1900 should make this car flawless as it is so I feel that they are attempting to rip me off even more.
Passat (B5) :: Code 17748 And P1340 Diagnosed
I just replaced my timing belt. Checked it at TDC several times, even after releasing the tensioner. Now Im getting a
17748 - Camshaft Position Sensor (G40) / Engine Speed Sensor (G28): Incor. Correlation
P1340 - 001 - Upper Limit Exceeded
Golf IV / Jetta IV :: CEL On With Camshaft Position Sensor Code And Misfire On Cylinder 3
She is a 1999.5 Golf 2.0 (although, she just has a rabbit symbol on the hatch, is she a Rabbit or did someone remove the Golf badge?) I just bought the car, with less than 160,000 miles. The dome lights work sometimes, Door Ding works intermittently as well, but sometimes will "glitch" in other words it will be making the sound but it kind of stutters? Odd? The horn sometimes works, however it is very silent? Check engine light is on with a camshaft position sensor code and miss on cylinder 3. Someone told me to replace the "109 relay"... could this be the problem or is this the CCM?
View 5 RepliesGolf IV / Jetta IV :: 2004 - Camshaft Position Sensor Error Code
I have a 2004 MK4 Golf 2.0l that's been throwing a CPS error code. My brother was going to come down to visit for a weekend. He had done some diagnostic work and had me order a timing kit and a camshaft position sensor from ECS.
So, with my assembled parts, I brought the car in to a reputable shop. Anyway, the guy does the work and now the car is ready and saying that the CPS took nearly 4 hours more of work.
Golf IV / Jetta IV :: 2005 - Code P0011 Intake (A) Camshaft Position Timing / Over Advanced (Bank 1)
2005 GTI 1.8t Engine ... I changed my timing belt water pump and tensioner yesterday and today I am receiving an engine code: P0011 Intake (A) Camshaft Position Timing - Over Advanced (Bank 1) My friend timed the engine and knew that is was 1 tooth advanced. He told me that is was going to be OK because 1.8t's have a 1 tooth tolerance. I would have redone it but I did not know how. What to do in this situation? Do I need to re time the engine?
View 2 RepliesGolf IV / Jetta IV :: Check Engine Light With Error Codes 17748, P1340
I'm having some problems with my 05 1.8T GTI. I've had a check engine light for about 3 months and finally got a diagnostic tool (VAG V-checker). Right now I have one code 17748.P1340 Camshaft position sensor-G40/engine speed sensor -G28: incorrect allocation.
I researched a little bit and talked with some of the guys at the local VW dealership. From what I learned this could be related to (obviously) faulty camshaft position sensor and/or faulty engine speed sensor. So I've replaced both of these sensors and even cleaned the Mass Airflow sensor.
I cleared the code and after driving about 5 minutes the code came back. Also I recently had a P0300 and P0304 cylinder 4 misfire default code. So I've changed all of the ignition coils too since I heard they were recalled a while back.
Golf/GTI VI :: Test Result Showed 1.4 / 1.6 Amp Battery Draw
So I think I have a slow battery draw. Did a test and the first result showed a 1.4/1.6 amp draw. So I started pulling fuses, and the F8 fuse (in the engine bay) dropped it to 0.4/0.5. F8 fuse is what I believe is labeled as the Radio. I have no audio upgrades. Just the stock RCD-510.
View 8 RepliesGolf IV / Jetta IV :: Screen Is Dead And Fuel Icon Showed Up
Is my screen fried? Cold weather came in and the screen died and the fuel icon showed up... Even tho I recheck if the guy lid is open...
View 9 RepliesTouareg :: 2004 - CEL Code P0022 For Camshaft Position
My 2004 V8 touareg is throwing CEL code P0022. 'A' Camshaft Position - Timing Over-Retarded (Bank 2)
What would cause this? I found that these all could be related:
- Valve timing
- OCV
- Camshaft timing gear assy
- ECM
Would any of these cause it to burn oil more quickly? What steps are taken to diagnose the whole problem?
Kia - Sedona :: CEL Came On While Driving / Code Read Camshaft Sensor
While driving home my cel came on, the next morning I took it to the dealership. The code read camshaft sensor. The mechanic ask how the van was driving, I said perfect, no issues no nothing. He said that was kind of surprising.
The next morning went out and no cel at all and van still running fine. Spoke with another mechanic who said a number of things can cause that code and to hold off on the new sensor and see what happens over the next few weeks engine performance wise and if CEL comes back on.
What should I do? Car is a 2002 KIA Sedona mini van that has had zero engine issues while I have owned it since 2010.
Accent LC (2000-05) :: Camshaft Position Sensor Code P0342
So my little car.....driving home from jersey (about an hour and a half) and within the last 2 miles I notice the car just shut off. Not any electronics just the motor. Pulled over and tried to start it an it just cranks prolly no fuel or spark. happened to have my obdII scanner with me. It says camshaft position sensor(po342). Only code in there. Sounds simple enough. Got a new one and put it in. Just cranks. Plugs and wires were done about 3 months ago and I drive about 40 miles a day 5 days a week. I did the timing belt last spring so I opened that back up to make sure the timing hadn't jumped for some stupid reason. It's perfect. Noticed now after doing all of that there is some (a little) oil in the throttle body. I know about blow by and don't think I should have that much at 113k but who knows.
View 2 RepliesElantra XD (2001-06) :: Camshaft Sensor Error Code After Tune Up
I just had a ton of maintenance done on my 2003 Elantra. Spark plugs & wires, timing belt, drive belts, water pump, replaced coolant and replaced the transmission fluid. The spark plugs are NGK platinum as recommended in my handbook. As soon as the mechanic started the car after the tuneup, the engine light came on with a cam shaft sensor code. He said it went off on its own.
The engine light came back on when I started the car. There's also a major loss of power after coming to a stop. I have to floor it to get it to go anywhere above 20 mph after a stop.
The mechanic said that when he replaced my water pump the liquid splashed all over everything and he thinks he might have gotten something wet that shouldn't have gotten wet and that all will be fine after it dries.
Elantra XD (2001-06) :: 2003 - CEL Code / Bad Camshaft Position Sensor
I am new to Hyundai. I just picked up a 2003 Elantra and I'm doing a couple fixes to it. When I got it, the engine light was on and the code displayed said it had a bad camshaft position sensor. Is this a common issue with the car and is it an easy fix?
Also, I just installed new brake pads and a new battery. Now the battery and brake lights are on, although I know I didn't break anything. Could installing a new battery cause the two lights to come on?
Accent LC (2000-05) :: Code P0342 - Camshaft Position Sensor
My daughter spun her timing belt on her 1.5L accent. when she did, she bent the valve rods and all were replaced. The original code that was thrown was the one in the title. Ordered a new camshaft positioning sensor for the car. Looks a little different than factory. He installed it, and car is still pulling code. He accidentally threw away the original before confirmed that the problem was solved. Why the code is still pulling?? I can tell you this, I can clear the code, start the car and drive without code coming back on. As soon as I shut the vehicle off and restart, engine light comes on. Car runs fine. Had a complete valve job, new timing belt and water pump installed.
View 2 RepliesCelica :: 1997 7afe 1.8 ST - P0340 Code For Camshaft Position Sensor
I am getting the code for the camshaft position sensor. Erase code, comes back immediately. I don't even think this car has a camshaft position sensor.. I guess the first step would be locating the little bugger. Crankshaft position sensor is new and seems to work fine. Car is running btw.
View 5 RepliesJimmy :: 95 Running Rough / Stuttering - Camshaft Position Sensor Code
I have replaced the camshaft pos sensor multiple times from Autozone (warranty ) and replaced with one from Advance Auto still get cam sensor code changed crankshaft sensor today still running like crap, stuttering. I have also done a complete tune up and the Distributor has not been pulled.
View 1 RepliesCamry :: Toyota 2002 LE 2.4L - Code P1379 Camshaft Position Sensor
The computer is returning P1379 camshaft position sensor. Where is this sensor located on a 2002 Toyota Camry 2.4L and how easy would you rate the job of replacing it?
View 3 RepliesLexus ES 2007-12 :: Code P0368 - Camshaft Position Sensor Error
2007 Lexus ES350 with 177k miles. Getting a P0368 (Camshaft Position Sensor B Circuit High Bank 1) Error. I can't seem to find online where this sensor is located at.
View 2 Replies