Golf IV / Jetta IV :: 1.8t Won't Start / Throwing 2 Codes
Throwing 2 codes -
P0172: too rich
P1176: post cat 02 reached limit
Last time it turned on it had horrible air flow, it felt as though it was choking. definitely not a misfire. occasionally after spirited driving the engine would die after I came to a complete stop then worsened to cutting off when I put the clutch in at high rpms. also have a slight loss of power. I also recently added a 3" tbe and changed coil packs.
Golf IV / Jetta IV :: 2.0 Throwing Multiple Codes
So my car has been dropping multiple codes after I scanned her and found all five: p0303, p1128, p0172, p1300, p0301. She is just a simple five speed AEG and has no mods other than a SRI. I already replaced the MAF but that ended up causing more codes and I have checked the vacuum lines to no avail.
View 2 RepliesGolf IV / Jetta IV :: 1.8t Throwing Codes And Misfire - CEL Came On And Blinks
So recently I took my engine apart to do a valve cover gasket and Ecs tuning 2.0 coil conversion. I noticed a good amount of oil in the plug tubes so I got out my trusty soap dispenser and started pumping out oil. Pulled plugs and cleaned them (wanted to make sure oil was all out b4 getting new) also while I had it apart I wanted to take intake off, ( just to polish it and clean out any carbon inside).. Well I never ended up doing that. I removed the injector connections and realized it was to much work for such little satisfaction. So I plugged the injectors back in.
I got my car all back together and now I'm throwing 6 cel codes!! P0102 (maf) which I'm assuming b.c I took it off for so long, p0201, p0202 ( injector 1 and 2 miss), then some misfire codes p0300 (random) p0301 (cylinder 1) and p0304 (cylinder 4). The car starts runs very rough then cel comes on and blinks. I was thinking maybe the oil getting down to the combustion chamber couldn't be the best for it but it would just burn off. Only other thing I did was take off the thottle body and cleaned it.
Golf IV / Jetta IV :: CEL Is On Throwing 3 Codes - P0171 / P2637 And P0420
What I need to do to fix these codes
p0171 system too lean bank 1
p2637 torque management
p0420 ...
Golf IV / Jetta IV :: Throwing P0300 / P0302 And P0303 Codes
The car doesn't seem to run that rough.
Replaced coil pack and spark plug wires with parts from O'reilly auto
16684 - Random/multiple cylinder misfire detected
P0300 - 35 -10 - Intermittent
16686 - Cylinder 2
P0302 - 35 - 10 - misfire detected - intermittent
16687 - Cylinder 3
P0303 - 35 - 10 - misfire detected - intermittent
I have searched and browsed multiple websites and threads to no avail. They all seem to be dead ends.
Golf IV / Jetta IV :: 2001 - Throwing Codes For Misfire / O2 Sensor?
So my girlfriends's 2001 2.0 Golf (engine code AVH, 153k miles) began throwing codes for misfire on cylinder 4 and for the o2 sensor (post-cat) recently. I went ahead and replaced the spark plugs, wireset, and the coil pack. They were way overdue. The CEL went away for like 30 miles, and then came back. Now it's reading misfire on cylinder 3 and the same thing for the o2 sensor. What else it could be? Search is coming up blank, most people replaced the coil pack and the CEL went away.
View 2 RepliesGolf V R32 :: Car Is Throwing Error Codes
I just has a gen 2 haldex and wireless controller installed. 10 minutes of driving around getting on it in sport mode, I feel a thunk from the back and when slowing down a few odd shudders. Drove it cautiously a bit more and felt fine, then harder and harder. Felt better, no understeer, seemed ok.
Got home and scanned with Vagcom, got the errors below, cleared DTC and scanned again, same errors.
Address 22: AWD Labels: None
Part No: HW0 5Ha lde x
Component: Tuning
Coding: 0000001
Shop #: WSC 00000 000 00000
VCID: 5AB1BED4953067CEBA7-800F
2 Faults Found:
16347 - Control Module - EEPROM Error
014 - Defective
02248 - Valve for Controlling Clutch Operating Angle (N373)
014 - Defective
Golf/GTI VI :: Foot Well / License Plate LEDs Throwing Error Codes?
Any LED I can throw in the footwells / license plate area that won't throw a code? I'm using the ones from superbrightleds.
They worked everywhere except the license plate and the footwells. Everytime I get in my car I have to see (check license plate lights!) and a bulb out icon.
Golf IV / Jetta IV :: CEL Recently Came On Throwing PO420 Code
I own a 2003 VW Jetta GLS 2.0L 4 Cylinder and my CEL recently came on throwing the PO420 code (Catalyst System Efficiency Below Threshold (Bank 1)). So I replaced both the upstream and downstream O2 sensors. Well just one day after replacing the sensors the CEL came back on with the same code. I was wondering weather or not I should replace the whole catalytic converter or if there was anything else I should try. The car runs fine, exactly how it did when I bought it.
View 22 RepliesGolf IV / Jetta IV :: 2003 - Throwing P0113 Code?
I have a 03 GLI 24v VR6 thats throwing a P0113 code, which is for the intake air temperature sensor. The sensor is part of the MAF sensor, ive tried 2 brand new BOSCH MAF sensors yet the same check engine continues to reoccur. Is there anything else that oculd be triggering it to come on? Is there anyway to bypass/disable it through vagcom?
View 8 RepliesGolf IV / Jetta IV :: EPC Light Came On - Codes P0221 And P2637
I bought my son a 2005 GTI MkIV (great dad right). On the drive home it threw a light the code was P4011 secondary air no prob found a hose off and issue solved. The car had 66k so I made him leave it at home until the timing belt was changed (read about alot of failures between 60 and 80k). Everything was great for 2 weeks last Thursday the EPC light came on and he got it home in limp mode. I pulled the following codes P0221 and P2637.
Am I looking for a short? I have read that it has been the following.
Brake light switch
Gas pedal
MAF
Intake manifold...
Golf IV / Jetta IV :: ASR Light Came On / Running Rough And Smoking With Codes
I was driving along the highway cruising at around 100 km/h when out of nowhere the car started driving a little rough so I look down and the ASR (traction control) light was on. I got off the highway, shut it down and fired it back up. The ASR light was off and car running like normal. When I got home I scanned it and these codes came up:
The catalyst code if from my catless turbo-back exhaust which I plan to fix next month with a tune. Anyway I cleared all codes and continued on my way without any other hiccups. So is my MAF sensor dying/dirty? ECU? N75 valve? Boost leak? I'm making a boost leak tester today just to 100% eliminate that variable, though I'm fairly certain I'm good there.
The car is mostly stock except for a few bolt-ons, all of which I've had installed for thousands of kilometers now. Here is what isn't stock, not including suspension, wheels, etc:
Forge 008 diverter valve
034 Motorsports PVC silicone hose kit
Samco boost hose kit
Forge silicone turbo inlet pipe
Eurojet SMIC
custom built 2.5 stainless, catless turbo back
AEM Dryflo short ram intake
GLI MFA cluster
Golf IV / Jetta IV :: CEL On - Exhaust Leak Throwing Catalyst Efficiency Code
I'm working on a 2003 Jetta GLI 1.8t (MT and 140,000m if it matters). The CEL has been on for a couple of weeks because of an exhaust leak throwing a catalyst efficiency code. After I make this post I'm going to run down to the advance auto I used to work at & see if I can borrow the scanner to see if there's anything new, but as of right now I don't know. I'll update the thread if I find anything.
The car started yesterday AM perfectly fine. Started again when I left work around noon. No problems with the start, idle, acceleration.. it's all good.
3 hours later I tried to start it to go pick up my kid from school but it just cranked without firing and would not start. I took care of business with the kiddo and then started trying to pin down the problem.
1. Opened the door & listened for the fuel pump to prime.. No sound.
2. Noticed the dome light is on.
3. Checked ALL of the fuses on the side of the dash.. All are fine. Turned key to listen for secondary prime.. no sound.
4. Bought Fuel pump relay & replaced.. no change.
5. Cursed.. a lot
6. Bought fuel pump.. replaced.. no change.
7. Cursed a lot more.. and cried a little too.
8. Noticed the fuel pump was now priming with the key being turned, but still not when I open the door.. Dash indicates the known CEL, but now I notice that the EPC light is on too (this could be from all the fruitless cranking drawing down the battery charge)
9. Figured I'd throw in a new crank angle sensor cuz of the EPC.. no change.
10. Shot starting fluid down the intake.. didn't hit a lick.
I feel like I'm at a dead end.. It's acting like a bad ignition control module, but there's no such thing on a vw 1.8t.
Golf IV / Jetta IV :: 2000 - Engine Light And Codes That State Misfire On 1 And 4
My daughter's 2000 Jetta with a 2L has an engine light and codes that state Misfire on 1 and 4. It is intermittent as it only misfires once in a while.. She is in Rolla MO, and I am in Detroit MI. A couple of years ago the car died when she was home and I found a swollen/cracked coil pack. I replaced it with an aftermarket. The plugs and wires were replaced about 30k ago with OEM parts. I am tempted to have the son in-law replace the coil pack with a Bosch unit.
View 3 RepliesGolf IV / Jetta IV :: Check Engine Light With Error Codes 17748, P1340
I'm having some problems with my 05 1.8T GTI. I've had a check engine light for about 3 months and finally got a diagnostic tool (VAG V-checker). Right now I have one code 17748.P1340 Camshaft position sensor-G40/engine speed sensor -G28: incorrect allocation.
I researched a little bit and talked with some of the guys at the local VW dealership. From what I learned this could be related to (obviously) faulty camshaft position sensor and/or faulty engine speed sensor. So I've replaced both of these sensors and even cleaned the Mass Airflow sensor.
I cleared the code and after driving about 5 minutes the code came back. Also I recently had a P0300 and P0304 cylinder 4 misfire default code. So I've changed all of the ignition coils too since I heard they were recalled a while back.
Golf IV / Jetta IV :: 2004 - Multiple Fault Codes / Random ASR Light Coming On
The vehicle is a 2004 Jetta MK4 1.8t.
Last thing I had replaced about 2 months ago was the Solenoid valve, the MAF and Solenoid hose. Car ran fine for about a month, and bam...engine light came back on, along with the ASR light. At first it was saying "cat converter" so I researched that, and what a surprise, it spoke about being a $1k piece to replace. NOTHING HAS BEEN CHEAP ON THIS CAR, and I'm losing my mind.
The latest adventure happened today coming back from the gym. Car started jerking (which has been normal since every now and then the ASR light will come on, which I'm told is the traction control light. Causing the car to jerk. Simple fix is pulling over, shutting the car off, and turning it back on. That always clears it, and then I'm back on the road.) but instantly it lost power. It wont shift, but the traction control light didn't come on. I plugged my OBD2 tool up, and came back with these fault codes:
P0420: Catalyst System Efficiency Below Threshold (Bank 1)
P0753: Shift Solenoid "A" Electrical
P2637: Torque Management Feedback Signal A
I'm going to go to these guys tomorrow, but I would just like to get an educated guess on what might be going on, so I don't look like a lost dog while they're figuring out what to do next. These guys seem knowledgeable, but they're missing something since I've been in and out of their shop several times and still getting my traction control light on at random times, and now all 3 of these codes.
Does that Solenoid code have anything to do with the Solenoid valve they put in? I was told that cleaning the throttle body and the cat converter might work. Would those be cheaper options to consider, and see if that works?
I also read that unplugging the alternator and plugging it back in, then cleaning the male and female with electrical cleaner might work. I was told about a month ago that my battery barely passed. Could this be causing any of my issues? I also did a log while I was driving, but all that's showing up is a google map document.
Golf IV / Jetta IV :: 2003 1.8 Turbo Throwing P0411 - Secondary Air Injection System Error
I keep throwing a P0411 - Secondary Air Injection System error. My previous pump was seized so I replaced it, and broke a few of the chintzy air hoses in the process. Now, with new pump installed and new air hoses connected, I can go about 5 days before the code comes back on.
So to recap, I have:
Replaced the air pump
Verified the new air pump functions, yepReplaced the air hoses
Verified connection of air hoses at all junctions
Checked the Secondary Air Relay for function
I have not yet checked the solenoid - unsure how to do so.
Golf IV / Jetta IV :: Check Engine Light With Codes 16804 , 17511, 17748, 16524
My check engine light recently turned on but I don't know what the codes mean. The codes are:
16804
17511
17748
16524
Passat (B5) :: CEL Throwing Codes P1136 And P1113
My girlfriend has a 2000 B5 and it's been throwing a p1136 (Fuel trim too lean: probably a vacuum leak) and p1113 (B1, S1, pre-cat O2 sensor) for about two weeks now. How long can she feasibly leave this stuff before doing any real damage?
I just don't have time to check her manifold for vacuum leaks for at least a few months (summer) or deal with the O2 sensor. I mean she doesn't need to get it inspected until Nov 2007, so, all she has to put up with is that really annoying beeping and "emissions workshop" lightshow every time she starts her car up.