Golf IV / Jetta IV :: Reverse Won't Engage Reverse After Transmission Replacement
I got a 99' Jetta gls 5 spd. I just replaced the transmission and now the car won't engage reverse from inside the cockpit. Reverse can be engage from inside the engine bay, but when the shift knob is depressed nothing happens. Linkag cables are in the correct spots.
View 6 RepliesGolf/GTI VII :: 2015 - Odd Engine Deceleration - Getting Error This Isn't A Good Time To Put Car In Reverse
Yesterday I was driving about 120 km/h on the highway, my 2015 GTI (DSG) suddenly decelerated to about 110 km/h -- the sensation was that the engine downshifted on its own.
The transmission was in Drive, and I wasn't in sport / automatic mode. An error message appeared on the dash display telling me, 'this isn't a good time to put your car in reverse' -- or something to that effect (I don't remember the exact wording as by the time I pulled over to the side of the road the message was gone, but the yellow warning notification symbol was still up.
I turned off the car, let it sit for a minute or two, and then restarted it. The yellow warning symbol was no longer lit up, so after letting the car idle of a minute, I pulled back onto the highway and proceeded to my destination without further incident.
The car is at the dealer this morning for diagnostics.... One thing to note: It's been very cold here in Ottawa, Ontario, Canada these last couple of days (-25 C) and yesterday I didn't 'warm up' the car as much as I normally would as I was running late for an appointment. Wondering if that might have had an effect... It's the only thing I can think of that's a variable.
Ford Super Duty (1999-2016) :: 2015 - Delay In Transmission To Engage When Start And Put Shifter In D
2015 F-250 4X4 CC gas truck. 6R140 Transmission..
My truck has 6500 miles on it and since day one when I put my shifter in (D) there is a 3-4 sec delay in the transmission to engage every morning when I start out, rest of the time there is no delay even when the truck sits all day at work (about 9 hours). I have read in 2011 (?) that the transmission was loosening it's prime and would cause this problem, so how it's got me thinking.
Corolla / Matrix 2009-13 :: Transmission Does Not Engage In Reverse On Chilly Mornings
I have 2009 corolla with about 125, 000 on it. A few times over the past couple of weeks on chilly mornings (in the 50's) the transmission did not engage in reverse right away. Usually with the fast idle you can feel it kick in but on these days it takes a few seconds before that happens. I have had the car for two years and have done nothing about transmission service. A dealer told me it was lifetime fluid and there is no dip stick to check it. Is this a common problem? Is this a sign the trans is on the way out? Should I sell the car now before it gets worse?
View 3 RepliesHyundai - Tucson :: 2005 - Transmission Won't Engage In Reverse Or Park Immediately
I have a Hyundai Tuscon 2005 with 140K automatic transmission. Original Owner and has treated me well. Current issue is the transmission will not engage in reverse or park immediately when shifted most notably first thing in the morning or in the late evening after sitting for a while. It acts as if it is in neutral until it engages after revving the engine for a while. Once it engages, it is a little sporadic for a few minutes and then all is fine for the rest of the day no matter how many times I start, stop or turn the car on or off.
Runs like a champ until the next morning and it starts all over again. A couple of times the check engine light has come on and I can tell that the transmission is stuck in 3rd gear. I can't manually get it to go up to 4th or down to 1 or 2. I can clear the code and then all is back to normal again with normal shifting again available. Short of a transmission rebuild (whihe probably won't happen) could it be electronic in nature since it comes and goes?
Mitsubishi - Galant :: 1998 - Delay In Transmission Development - Won't Engage In Reverse
I have a 1998 Mitsubishi Galant, 4cyl., 165, 000 miles. Without previous symptoms, one day the transmission developed a delay of 5 to 30-seconds before it would engage in reverse. The fluid was clean and I have been using the Mitsubishi brand that they recommend. So I replaced the original transmission with a used one. But the reverse delay continued, even with a different transmission. So I removed the used transmission and rebuilt the original one. The problem STILL remained. Since then, the valve body has been replaced and the speed sensor has been replaced. I cannot figure out why there is a delay when putting it into reverse. I ran out of solutions. I did notice one day that when I first start the car, and the engine is at 1000 RPM's or more, the reverse wouldn't engage. Then, as the RPM's dropped to about 200 RPM's, the reverse would engage. I thought maybe this would be a clue.
View 10 RepliesTrans Sport :: 3T40 Automatic Transmission Suddenly Won't Engage Drive Or Reverse
This transmission shifted smooth and strong through all gears until today when it stopped all of a sudden to engage either Drive or Reverse. No previous signs of slippage, hesitation, stalling or lack of power whatsoever.
We checked the linkage to the transmission and it works as intended, nothing loose or broken, everything is in place. If there was something slightly different with it from other similar vans we have then it had a slightly delayed engagement in Drive (it took a second to engage it after you moved the lever) - on all other vans we have the transmission go into Drive almost instantly.
Van is a '92 Pontiac Trans Sport/Chevrolet Lumina APV with the 3.1L V6 Chevy TBI engine with the 3T40 automatic transaxle. Where we should start tackling this issue?
Ford Transmission :: 2005 F350 - 3 To 4 Seconds Delay When Trying To Engage Drive Or Reverse
Still having issues with the transmission on my 05 F350. I posted before that it would take a few seconds to go into drive or reverse. The fixes were to change filters and do hot flush. I had the dealer do a hot flush, and then I put about 1000 miles on it. That didn't seem to fix anything, so I went back in and asked for more info. They did not change the filters. I thought they did, but found out they did not after the fact, so I decided to change the filters myself.
The interior filter was easy to change. The fluid was clean, and the magnet had shavings on it but nothing that seemed extraordinary. The exterior filter is impossible to get off. I reviewed posts on here before trying, so first was the impact wrench, then the pipe wrench, then the pipe wrench with a block wedged in to keep the thing from bending, still no luck. The cast nut broke off well before the pipe wrench came out of the drawer. How to get that thing off. I read on here somewhere that no fluid goes through that until 180 degrees, is that correct?
Scanguage says it rarely goes over 160, except for last evening when I was stuck in traffic. It went to 187, with ECT at 208. During this period, traveling under 40 most of the time, the transmission was shifting erratically, to the point I wanted to pull over and allow it to cool down. But traffic broke free, speed went up, and temps went down. Shifting returned to normal, except when trying to engage drive or reverse. The 3-4 second delay persists at any temp, and there doesn't seem to be any slippage. Just delayed and sometimes hard engagements. I'm at a loss for whats wrong.
LS / MKZ :: Transmission Shift Error Displaying When Car Shifted To Reverse
2002 LS V8 162K Miles. Its been sitting in the garage for 10 days. ...went on vacation. Started her up and let it idle down. Shifted to reverse and transmission shift error displayed. Went back to P. Waited a minute. Shifted again and she was hard jumping into the gears. The error went away. Drove it around and it seems to shift fine. Opinions?
View 4 RepliesFord Super Duty (1999-2016) :: Transmission Will Not Engage In Drive Or Reverse After Replacement
I have a 1999 F250 super duty that blew a front seal on the transmission two weeks ago. I sent it to a shop and they replaced the seal, and torque converter. However when they put it back in it will not engage in drive or reverse. After working on it several days we replaced the transmission with another one from a service company. This replacement came with a 90 day warranty. However once it was installed it does the same thing and will not engage in drive, or reverse. I am not sure what is going on but with two doing the same thing it makes me thing maybe electrical or something else.
View 1 RepliesFord Transmission :: 1991 F250 - Truck Is Slow To Engage In Reverse Taking About 5 - 10 Seconds
1991 4x4 f250 idi w e4od w 3:55 ratio... The truck is slow to engage in reverse, about 5-10 sec. It also has a very hard shift 1-2. All other shift points are good. Drop down is good, and TC lock up happens at all the right points (feels like anyway).
I've had the truck for about 2 years now, replaced several sensors an harnesses and a full fluid change to solve other problems but this still remains.
Sometimes when I start it in the morning if I let it sit and idle for a few min it will engage reverse much quicker AND shifts way smoother and constant. Shifts smoothly thro all gears, holding a constant 1800-2000 rpms with no drop or lug. Or do I need a rebuild?
Golf/GTI VII :: Cannot Engage Reverse Warning And CEL Came On - DSG Failure
MK7 GTI - I was driving along yesterday when I got a warning message that said "cannot engage reverse," accompanied by a CEL and the transmission downshifting into 1st gear (luckily I was only going about 20 mph.) I tried pulling over and restarting the car, and tried shifting into the different transmission and engine modes, but the transmission continued to only be able to engage 1st gear or neutral. Luckily I was five minutes from my APR dealer, and cruised over there at 15 mph so as to not over-rev the engine in 1st gear, a lot of pissed off traffic was flying by me honking.
They ran the codes, flashed it back to stock, and the codes and CEL persisted in stock mode. I drove back to my house at 15mph, took my intake off, and called roadside assistance to tow my car to the dealership. They are currently waiting on a rep to come out and authorize a new DSG most likely.
Ford 7.3L Power Stroke (1999-2003) :: 2002 - Transmission Work Slowly - Hesitates To Engage Drive After Reverse?
I have a 2002 7.3 e350 quigley 4x4 Sportsmobile with 312k miles. 2nd owner. Bought it with 295k miles 2 years ago. From what I gathered the tranny is original.
After reversing at a downhill angle, stopping, and shifting the lever to Drive, the tranny doesn't seem to put Drive in gear and depending on the angle of the slope, the van will roll back or barely creeps forward even with throttle. Put it in 1st gear, and the tranny engages that in gear and drives forward no issues, then I can shift to 2nd, then Drive and the tranny shifts fine after that.
No weird tranny noises or clunking. Noticed this issue about a month ago or about a couple thousand miles ago. Did tranny service (drain, filter, fill) at the ford dealership at 305k months ago.
I can only replicate this issue when Reversing on a down slope. On a flat surface van Reverses and engages Drive like normal.
Golf/GTI VII :: 2015 - Delay When Engaging Reverse
I have a 2015 with 10k miles on it and every once and a while, when I come to a complete stop and shift into reverse, I take my foot off of the brake pedal and the car will sit there for up to 5 seconds. Then, it kicks in and starts rolling backwards. This has happened 6 times now. Giving it gas doesn't seem to work along. I took it to the dealer today for it's 10k service, and they cannot find anything wrong with it. There are no codes in the computer, the fluid is where it should be, and they think the Neuspeed Power Module has something to do with it. I told them it happened before I installed that piece. I can assure you I am not racing in reverse.
View 7 RepliesGolf/GTI VI :: Transmission Shifter Goes Into 5th But Would Not Engage
Out of nowhere the car wont go into 5th, so I need to check the cables adjustment and if that doesn't work go from there. This car as of now is nothing more than a daily driver, never driven hard. I bought it last June with 40k on it and as of today it sits at 68k. Happened Friday worked fine on the commute to work, but on the way home once I got on the highway I noticed it would not engage 5th. Does not grind, pop, or anything. It is like the shifter goes into 5th but the cable has been shortened to not engage. This may be the issue but reverse, and 1st-4th work great with no issues.
I also read about the narrow oiling holes for the 5th gear and they are very easy to starve when temperatures get too low, which it has been roughly 0-15* here. I also read that the seal on the transmission gear shift unit (0A4301230H) can get worn out and allow back and forth play in the shift unit. Lastly the 5th gear is pretty weak and teeth like to shear off.
I had installed new shifter bushings the week I bought the car, and the fluid was flushed and replaced with Liqui Moly and their MoS2 additive about 5k miles ago. I'm hoping it is just the cables out of alignment due to the cold, but if not I will explore the options, as I have priced out all of the replacement parts and it'll be around $1k to replace the gear, 5th synchros, shift fork, and the gear shift unit. So a 02Q might not be out of the question.
I tried to manually pull up on the selector and move it right into the 5th position. Would not engage, so I am lead to believe that something is either wrong with the selector shaft of the transmission or the 5th gear itself.
Golf/GTI VI :: Euro LED Tails With Fogs - Reverse Lights Throwing Error
Had the tail lights coded for at a local shop.. realized as I was leaving that the reverse lights are throwing an error. Can these be coded for? Now that the car recognizes the tails as LED, is the error coming from the incandescent? Should I replace the bulbs with low pulling LEDs without resistors? As for the fog, do I have to replace the bulb as well? No euro switch or wiring done. Basically, how do I get rid of the error.
View 3 RepliesGolf IV / Jetta IV :: Auto Transmission - 4th Gear Won't Engage
I'll start this off with a few months ago, I went on a trip and along the way noticed that the car wouldn't get into gear. This happened for a few moments, and solved itself.
Fast forward to a few days ago:
So, my Golf MK4 AUTO 1.6L transmission doesn't want to shift into 4th, sometimes.
One and two are good, but sometimes I get quite a lag in between disengaging 2nd and getting 3rd also.
Furthermore, sometimes I get 4th 'semi' engaging, where the engine is revving too much to be fully in gear, but I get power to the wheels and accelerate (slowly).
I did a VAGCOM scan and got the old:
00652 - Gear Monitoring
27-10 - Implausible Signal - Intermittent
I also had a CEL on my dash, which I cleared with the VAGCOM. This removed the light, but of course the error still persists.
I've been reading around, and some people have said the issue is the TCM, but some people have had similar problems and a TCM replacement has not fixed this.
(Just btw, my TCM model is 01M927733LK).
And some people have had good results with solenoid replacements. So, I was thinking of doing a ATF flush, just because it was recommend on some posts, but won't necessarily fix the problem.
Contacted a garage to do this for me (never flushed automatic tranny before) and mentioned the VAGCOM codes, and he said this is a slip code.
So, now I'm not really sure what to do to fix it. Are the solenoids interchangeable? Am I able to switch two gears' solenoids to see if it moves the issue to another gear, proving its the solenoid?
Golf IV / Jetta IV :: Automatic Tiptronic Transmission - When Driving Does Not Engage On 4th Gear
I have a problem with automatic tiptronic transmission my golf MK4 TDI 1.9 2001, it dosent engage on 4th gear when i am driving, the codes that I received for this foults:
01316 - ABS CONTROL MODULE
49-10 No communication- Intermittent
00652 - Gear monitoring
27-10 - Implausible Signal - Intermittent
Sonata I45 (LF 2015+) :: SCC Just Won't Engage
Here is a quick video I shot the other day. This is the second time this has happened where the Cruise just won't engage. There is no error showing other than the message that comes up when I try to engage the cruise (Cruise on, press switch to the bottom to set.)
I've seen this same error if I try to Resume speed without having previously set the speed, but this was not the Resume being selected, but the Set.
[URL] .....