Ford :: Buzzing / Rattling Noise When Clutch Engaged To Shift To 3rd Gear
My manual 2004 Ford Ranger XLT (4.0L) has been Buzzing/Rattling. (VIDEO LINK BELOW) She has 112k miles on her. Owned 1 month, no issues when I bought from my paps. Its my 1st manual so may have been a little hard on clutch 1st few days. Noise started abruptly 1 week ago when I engaged clutch to shift to 3rd. Its gotten worse over the few days and happens even when in gear. Its much more prominent from outside passenger window. Don't notice for 1st couple mins of driving & is intermittent but often. Noticeably louder when foot is taken off gas in motion. Does not make noise when idling. Generally only above 1500 RPM . Not coming from the back half so I don't think its the exhaust/heatshield
Heres the sound......
Honda - Accord :: 2007 - Manual Transmission / Clutch Pedal Made A Slight Snap Sound
My clutch peddle made a slight "snap" sound last night and now it is very difficult to get the car to engage in a gear while sitting still, while moving it does ok, but not nearly as smooth as it should be. The other odd occurrence is that while the motor is running and the car is not moving, you can't shift any gears at all, but as soon as you cut the motor, all 5 gears and reverse are easily accessible. Why the sound at the peddle and the trouble in the gear shift mechanism? I am only an advanced beginner with car repair, but I think think this is really bad...
View 1 RepliesFord Transmission :: Manual 5 Speed Trans - Spinning Noise After Push The Clutch In
My cluch is almost 2 years old and gets treated with kid gloves , I shift low in the RPM's And accelerate slow for smooth shifting and fuel savings (17mpg avg.). But as of yesterday I can here the gears wind up after I push the clutch in. No problems with power or gear handling , Just the sound of the gear(s) (low dry rev/wind sound) No visible leaks , Clutch has oil at the step mark. Also - I can Make The Trans create the same sound if I keep the clutch petal in and rev the engine.
View 3 RepliesFord Transmission :: 1996 F150 - Rattling Noise As The Clutch Engages When Taking Off In First
1996 F150 4x4 with 300/6 and M5OD mazda tranny. 145k miles on it and looking really clean, and just the truck we wanted. It used to be well cared for, but has been a bit neglected since the owner passed away.
I spent a few hours searching the forums here and didn't find anything matching my symptoms exactly so I thought I would just jump in a post, but if I missed a thread feel free to redirect me.
I've got a bit of a rattling noise as the clutch engages when taking off in first. Once the clutch is fully engaged it's quiet and it shifts well and smooth. Noise also occurs (but less so) if I don't match RPM's and ride the clutch into second or third. I don't think its engine noise from lugging or anything because it goes away as soon as the clutch is fully engaged or disengaged.
Changed the trans fluid last night and no different, Clutch fluid reservoir is full, clutch travel feels good, master cylinder looks good, (slave is hidden, but looks dry though dust cover) a little play in the white bushing that holds the clutch pedal bar in place, and the plastic pushrod that goes into the firewall, thinking about replacing this linkage.
I work on big diesels for a living so i'm not scared of getting greasy. I'm almost inclined to think someone did a clutch job without resurfacing the flywheel. Is there an improved replacement for the pedal bracket and linkage? I don't mind just doing the clutch, but I don't want to be throwing my money away.
Ford Transmission :: 1987 F250 - Rattling Noise When In Neutral And Stops When Put The Clutch In
I just recently picked up a 87 F250 with a 6.9 and a ZF5 trans. The PO replaced the clutch, and mentioned that he replaced the clutch fork too
Since I bought the truck, I've had some nasty rattling noises. It rattles when in neutral, and stops when I put the clutch in. The noise also comes back on occasion when decelerating at highway speeds, in 2nd as soon as I stop accelerating, and at low speeds in 3rd.
What is causing this?
Ford F-150 - 1997-2003 :: 4x4 Light On Lower Right Of Dash Pops On When Clutch Pedal Is Engaged
I have a 1997 F150 XLT 4.6, standard transmission. the problem is every time I push the clutch the 4x4 light on the lower right of the dash pops on the power windows and windshield wipers will not work, releasing the clutch everything and goes back to normal, I checked the relay that was clicking every time I push the clutch in and switched it out same problem. As of yesterday the problem has now reversed, when the clutch is released everything doesn't work and a 4x4 light pops on.
View 6 RepliesGolf/GTI VI :: Rattling Noise Whenever Let Off The Clutch
I am a new owner of a 2011 Tomato Red GTI and was wondering if the sound my car makes is normal. Whenever I let off the clutch the car makes a rattling noise and i can feel it with my foot. Is that normal in our cars?
View 13 RepliesGolf IV R32 :: Transmission - Loud Clunk When Releasing Clutch Pedal
My R has been giving me some trouble lately. First I had some issues, I thought were clutch related.
-A loud clunk when releasing clutch pedal (only when engine running) and sometimes when depressing it too.
-Randomly changing clutch biting point when driving hard. So e.g. when revving through 1st and 2nd gear the clutch would bite much lower than usual. (This was so weird.)
-Whistling sound when changing from 1st to 2nd gear.
Replaced the clutch, flywheel, pressure plate and the TOB and bled the system several times. Also new solid DLI motor mounts and new oem dogbone mount.
There was some side-to-side play on input shaft that I was told is not a big deal. Also this gearbox has always been much louder than other cars Ive driven.
Now that weird changing clutch biting point is gone but other issues are still there. And now, because of the lightweight smf and the motor mounts the gears shatter and whine so much more on low revs and during engine braking. I know 02m s tend to do that but its so loud I am a bit worried.
Golf IV / Jetta IV :: Transmission Knocking When Clutch Pedal Released
I've done a bit of research both here and on other sites. I originally thought that I had a bad flywheel but I'm not convinced. First I'll give a little backstory. I just installed steel shift forks because one broke and got jammed in the gears. None of the gears are damaged and I assumed that when it slammed to halt, the flywheel got messed up. So anyways, the complaint is that when the clutch pedal is released I start to hear a knocking sound which becomes more rapid with RPM. When the pedal is depressed the sound goes away. This sound seems to be coming more from the driver's end of the trans. The car still moves in all gears so I can't imagine that I put it together wrong.
View 6 RepliesPassat (B5) :: Leaking Brake Fluid - Clutch Pedal (manual) Does Not Return All The Way
Over the past week I have noticed leaking brake fluid and after my STOP Brake failure light came on I topped off the brake fluid and it is down to a low level again. I also notice that the clutch pedal (manual) does not return all the way when the brake fluid is low and I assume they share the same fluid. I'm going to take it to my mechanic but could this be a clutch problem or just a fluid leak.
View 1 RepliesGolf IV / Jetta IV :: Clutch Pedal Is Rock Solid Hard After Transmission Swap
2004 Jetta 1.8 bought mainly as a parts car w /204K miles on it. Ran and drove fine, but the tranny had no 1st gear. Tried all sorts of things other than going inside the transmission and figured it is/was a bent shift fork. Clutch worked perfectly. Had another 02J tranny from 2003 1.8, so we swapped trannys. Could not get any response from the clutch.
Start the car in neutral and it won't disengage enough to shift into gear. Start it in gear with clutch pedal in and it is obviously slipping/burning/chattering. Have bled the slave cylinder to no end, have reverse pressurized it into the reservoir , etc, etc. Made up a block off plate to go over the end of the slave actuator and when the actuator is "blocked" from moving the clutch pedal is rock solid hard. Yet, the clutch acts as if the actuator isn't extending far enough. Have swapped out the original slave cylinder with the one from the '03, no change.
Removed tranny yesterday to check the condition of the throw out bearing and pivot and Pressure plate. All appeared fine. Reinstalled tranny and same issue.
Escort :: 95 Manual Transmission / Clutch Never Slipped
95 Ford Escort 1.9L, 330,000 miles. Never changed the clutch and i bought it with 80k on it. With that said the clutch never slipped and a lot of this is highway mileage so i never saw a reason to change the clutch just because.
Last week i pulled into the driveway i depressed the clutch pedal as i normally do and as i slowed, the car bucked like it was still in gear and didn't recognize the clutch was depressed. When it started bucking i tried to pull the gear shifter to neutral but it wouldn't move, the car finally died in it's parking spot. I quickly popped the hood and had my son press the clutch in and out and all components seemed to be moving fine, i was mainly looking at the slave cylinder assuming since it's a hydraulic clutch if it was a hydraulic issue that wouldn't move if i didn't have hydraulic pressure.
No obvious leaks were noted, i looked at the master cylinder and it seemed a little low but not empty maybe just above min. I filled it to max and still no change. So i assumed it was the clutch finally disintegrated and locked up. Yesterday i got in the car to attempt to move it to the garage to work on it. It started up fine, shifted through all gears with no issue's, drove it around for about 15minutes shifting a lot and pressing the clutch randomly and it worked fine.
I brought it back home and tried to kill it a few more times before i got it to the garage, it finally locked again but it was in neutral and i couldn't get into any gear. Turned the car off and then restarted and it shifted into gear, i pulled it into the garage and stopped with no other issue's.
Checked closer for leaks, between master and slave and couldn't find any. Pulled speedo cable and checked trans fluid, its brownish red (more brownish) and thin but didn't really smell burnt and it is at the correct level. Linkage has some slop in it but i don't see it binding anywhere, i layed under the car and was able to move linkage in/out of gear with my hand. It's easy enough to say the clutch is well over due for changing but since there were no signs of a failing clutch when i drove it i think i need to look elsewhere.
Could it be worn fluid? Could it be debris in the line? Or could it be that the fork just isn't engaging or disengaging properly due to wear?
Prius (2004-09) :: 2006 - Rattling Noise When Combustion Engine Is Engaged
My '06 Prius just started making this noise. the check engine light is NOT on. I haven't really heard this noise before in my recollection. I just got an oil change 3 days ago and when I got the oil change there was no indication from the dealership that there were any issues. The engine only makes this noise when the combustion engine is engaged. I can't see any wobbling on the belt drives or and loose parts in the engine. The spin appears to be coming from the engine block or around the pullys for the belt. My first thought is that it could be dirty gas because I first heard this sound after filling up. I am 300 miles from home and have to drive home today.
View 1 RepliesHonda - Accord :: 2013 - Manual Transmission / Clutch Completely Gone
I have 2013 Honda Accord 6 sp manual with 25k miles on, its clutch was completed gone last week, got new replacement, local Honda customer rep. told me I should watch my driving pattern, should using more break, instead transmission slow down, particular from high speed/high gears. I told them, we have 2008 Civic 5 speed Manual, I taught my two daughters how to drive it, and the car is still running without any problem… And, this is manual transmission car, tell a driver can not using/changing gears slowing down car is a joke… but maybe I am wrong...
Is there a possibility Accord has design problem with inferior clutch materials used on their new 6 speeds manual Accord? Since car has new clutch, should I keep it for a while? Or, sale it immediately? I just can’t not see I am going to come up another 3rd replacement on clutch before the car get into 60K miles.
Ford - Ranger :: 1997 - Clunking / Rattling Sound In Manual Transmission At Random Times
I have a '97 Ranger with about 120k, 5 spd manual transmission, 2wd. For the last 2-3 months I'm hearing and feeling a clunking or rattling noise (I can't decide which it is) coming from the rear of the vehicle at random times.
I can't really predict or find a pattern of when the noise will happen, but it seems like it is most likely to happen when I'm either accelerating up a hill or when I'm braking relatively hard. It happens whether the clutch is in or out. Doesn't seem to matter. It does NOT happen when idling, only when traveling. I don't ever remember it happening at highway speed (65mph).
If I have my hand on the stick shift I can feel the shaking / rattling as it happens. There seems to be no impact on the performance of the vehicle - no additional trouble shifting into or out of gear, accelerating, or anything else.
On a recent trip I towed a 1,000 lb trailer and I did not feel or hear the noise at all during that trip (about an hour each way). Any guess as to whats going on?
Golf IV R32 :: Warble Noise When Release Clutch Pedal To Accelerate
When I release my clutch pedal to accelerate, there's I guess a "warble" noise is the only way i can describe it. its been like this since i got the car a couple months ago. Is this normal?
View 4 RepliesGolf IV / Jetta IV :: 2003 GLI - Air Compressor Clutch Will Not Getting Engaged
I have a 2003 2.8 GLI and my compressor clutch will not engaged i provided the clutch with a direct power and ground from the battery and it engaged. i also went to the junk yard and got a couple of Fan Control Module ($4 each) and it still does not engaged.
View 3 RepliesGolf/GTI VI :: Engine Noises Coming When Idling With The Clutch Engaged
I've been noticing my GTI has been making some weird noises, especially after only have 380 miles on it. When idling with the clutch engaged, it makes a rattling noise that goes away when depressed. There's also a rather loud sound coming from the timing belt and just underneath the plastic engine cover. I'm hoping it just needs breaking in, but I'd just like some reassurance that it's nothing serious.
View 8 RepliesGolf IV / Jetta IV :: Clutch Not Stay Engaged After New AC Compressor Installed
99 Jetta, installed a new AC compressor a month ago, has been working great, not clutch will engage for a few moments, then turn off for a minute, then engage again. Seems, like there is Freon in there by the gauge on the low side.
View 4 Replies