Golf IV / Jetta IV :: A/C Clutch Not Engaging
My mother In law's a/c is not working. Last year I replaced the compressor, fcm, and pressure sensor and nothing. Well fast forward a year and I'm here again trying to sort it out. I unplugged the connector to the compressor and there is 2 black wires 1 wire has 6 volts (not 12v) and the others reads nothing. When I turn the A/C on the fans do come on.
View 6 RepliesGolf IV / Jetta IV :: AC Clutch Not Engaging
Driving home yesterday and the ac wouldnt come on my 2003 golf. Worked fine day before. All fuses are fine. Small fan works but large one needs to be replaced but its been that way. Ac button works fine too. What else would cause the clutch to not engage? I believe the pressure is fine as it worked fine the day before.
View 3 RepliesGolf V R32 :: Clutch Is Not Fully Engaging
I'm just over 45k miles, have a new mechatronics unit as of 39k, and I am beginning to see a new symptom for the first time since the replacement.... wondering if any of you have experienced this.
It's happened 2 or 3 times in the last couple weeks. The symptom suggests the clutch is not fully engaging. It is as if I had the clutch pedal in while in first gear, and I am feathering the clutch. This happens in "M" mode -- but I basically only drive in M so cannot say if it may happen in D or S.
Today, for example, I was at a red light on an incline. Light turns green, right foot off the brake and onto the throttle. Engine free spins up to nearly 4k and the car hold its position on the incline, without any movement or even a hint of movement. But there apparently was enough force going to the wheels to keep the car on the incline.
The engine does not rev as if it is in LC mode. It is free revving without any sound of it being under load.The clutches seem ok, this is not a clutch slippage problem. It's something occurring in the DSG's control.
I called my service advisor and he looked me up and said I have the latest and greatest MU, and my VIN does not qualify for the recent MU recall that is in the works. He said to just keep an eye on it for now (of course)
Golf IV / Jetta IV :: Air Conditioning Clutch Not Engaging
Here's the story: was on my way downtown last night to get a new suit (I'm in Savannah, GA so it's hot) and AC was working great. The Jetta (2003 AWP) is a stock-everything-1.8T that has never had any AC work done to it from the day I bought it new. I figured it was doing just fine so just leave it alone. Anyway, leave the suit shop (bought a gray three-piece) and go back to the parking lot, start up and get ready to leave, no cold air from the vents. I get it home and do some reading on here and also in the Bentley manual and get into some preliminary troubleshooting. Here's what I have so far:
- Engine running/AC button ON/Blower on "3"/Recirculation OFF/Engine at operating temperature
- Turn blower ON - visually verified that clutch is not engaged and compressor is not spinning
- Shut car off, compressor does turn by hand easily
- With AC button on and blower on, passenger side cooling fan (behind radiator) is ON but driver side cooling fan IS NOT on - I think this indicates a problem from what I've read
- Checked cabin fuses 5, 16, & 25. All have low resistance (good continuity) and are not discolored. Just to make sure I scuffed the contacts with a scotchbrite pad and reinstalled them
- Same deal for the top-of-the-battery power distribution block. All fuses checked okay and were scuffed and reinstalled
- Moved on to the pressure switch/pressure sensor. My vehicle has the 3-pin sensor so jumping contacts is not a possibility. I need to rent/buy a duty cycle meter to check it. Any good tutorial on how to do this? Do I disconnect the connector and check it right at the switch or must I break out the wires and check it in parallel with the connector attached to the sensor?
- I grabbed a flat-head screwdriver and gave the high-pressure and low-pressure service valves a poke and got a good blast of pressure from them so I don't think the system is empty.
- Did a little more reading and found I needed to check voltage at the 3-pin connector on top of the battery power distribution block. I did this with the key ON - no power at any of the pins. Repeated with key ON and engine running with AC button ON and blower ON - still no voltage. For these measurements, the connector was DISCONNECTED. Does this matter? Do I need to have it plugged in to get voltage there (i.e., read the voltage from the rear of the connector with it installed?)
- Finally, and perhaps most enlightening, I suspected I may simply be low on R134a so I bought a can with a pressure gauge on it. Connected it to low-pressure side with engine running, AC button ON, blower on "4", recirculation OFF. The gauge read ~150 PSIG. Yes, this seems high to me too; however, the compressor is still not turning at this point. Does it need to turn to get a good pressure reading from the LP service valve? I recall from everything I read that if pressure is too low, the clutch won't engage, and if pressure is too high, the clutch won't engage
So, as far as I can tell I have a few problems...
1. The driver side fan doesn't run when AC button is ON
2. No voltage at the 3-pin connector on the battery power distribution block Incorrect methods...there is voltage there.
3. Low-pressure side of the AC system is too high Called and checked with a local mechanic...I won't receive correct pressures if the compressor is not turning.
My next steps are to check the voltage at the compressor connector for 12VDC. I suspect I'll get 0V because it's clearly not turning. I'll do this once I can figure out how to get the dang connectors apart without breaking them. 11-year-old heat fatigued plastic is brittle...
Finally got the compressor connector apart.. there is 12VDC on pin 1 and 0VDC on pin 2 (it's a ground, so there shouldn't be..ground continuity check good). Ohmed out the clutch...from what I can tell, that circuit is open. However, I am not 100% sure I was on the contacts because of how the connector is positioned. I'm going to get a dummy connector from a salvage yard and connect it up and make sure I have good contact before I call it a bad clutch.
Golf IV R32 :: Wheels Not Engaging Off - Clutch Burnt
I got my R32 back 2 days ago after deploying to Iraq for a year. Upon driving it for the first time I took it a little easy on the car. I made sure the clutch was fully out before I did anything silly and what not.
Today I took it to the track and on the first launch I dropped it from like 3500 rpm and the RPMs shot up to 7500 and the car was moving at like 5 mph. I hit second gear and the rpm almost instantly shot up to 7500 rpm's again with the car moving at like 10 or 15 miles an hour.
After that, i let off completely. I tried one more time out in the warm up area to see what the hell was going on. Did the same thing. I could smell what I'm guessing was clutch burning pretty freaking bad. I'm, not 100% sure it was the clutch because I've never smelt a clutch smell that strong before.
Golf/GTI VI :: 2010 - Clutch Not Engaging Correctly
So i just took my 2010 Golf 2.5 into the dealer because it was not going into gear. Its a 5 speed with 12, 900 miles. They tell me they have to pull the trans and open it up before they can even tell whether or not the problem is covered under warranty!
View 16 RepliesGolf IV R32 :: Clutch Gargling When Slowly Engaging?
Lately I've noticed that when slowly engaging first or reverse, the clutch has noticeable but not loud chatter, kind of like its gargling a little. I JUST changed the trans fluid from OEM to Amsoil 75W-90 API GL4 and its about the same time the noise came, but I'm not going to assume right now that this is the source of the noise. Clutch acts just the same, apart from this gargle.
Might be worth mentioning that this all seems to have started about the same time the temps around here started to dip below 30 on a regular basis
Golf IV / Jetta IV :: Clutch Engaging Slowly When Turn The AC On
Got a weird issue that I've never encountered before. I tried searching but you can't search for just "A/C", so the search was pretty generic and I couldn't find anything similar to my issue.
Hot or cold, doesn't matter. When I turn the A/C on the clutch try's to engage and slowly starts to spin with the pulley until until it finally engages then the a/c will blow out cold air just fine. Also noticed a burning smell coming from it.
01 Jetta 2.0
Golf/GTI VI :: Clutch Would Slip And Then Bang While Engaging After Raining
Today I parked my golf on the street and it was raining, when I came back to the car after four hours the street had flooded and water was about an inch below the bottom of the door on the driver side, and about an inch (or more) on the passenger side and up to the bottom of the exhaust pipes in the back.
The car started fine, but when I began to drive it the clutch would slip and then bang while engaging. Once I had taken off a few times gently everything smoothed out. Car drives fine and the engine bay was dry when I got home (a 40 minute highway drive). NO water got inside the car at all, so the interior was completely dry, every thing appeared to function perfectly. My question is, assuming just the bottom of the motor, trans, and undercarriage got wet is there anything I should be weary of? Any sensors or electrical things down there? Lights, ac, door locks, everything is working and running fine and dry at this point.
Golf/GTI VI :: EPC Light Came On When Slowly Engaging The Clutch While Accelerating
The other night I threw an EPC light. I've tried reading older posts but haven't found anything.
I was at the top of a hill, slowly engaging the clutch while accelerating. I wasn't trying to floor it or anything. My car immediately went into limp mode and the EPC light came on. I pulled over, restarted the car, and it went away. It happened again the next day in the same place.
I am only having the problem on a steep hill while engaging the clutch. Other than this situation, the car seems to be running fine. The car is completely bone stock. I don't have a VAGCOM and can't really afford to purchase one at the moment.
Golf/GTI VI :: Screeching / Metal On Metal Noise When Engaging Clutch?
For the past few months, pretty consistently, whenever I engage the clutch from full stop into first gear (it does it when starting in second gear too; and reverse) there is a pretty obnoxious and loud screeching noise that I would liken to a subway/train braking or just metal on metal grinding situation. When I took the car in to Douglas for an oil change and APR Stg 1 flash, they told me it's just the brakes being cold, etc. After driving the car some more, I really doubt that it's the brakes and I can reproduce this regularly by slowly releasing the clutch and get the noise usually just before the gear engages.
That car has just over 16K on the clock and has never been abused. The clutch pedal feels fine and there is no issue shifting into any of the gears other than the noise. No mods other than the APR Stage 1.
Golf VI R :: Clutch Clicking While Shifting Between 1st, 2nd And 3rd Gear
Last couple morning here in Michigan we've seen temps in the low to mid 30's. The last two mornings when I shift between 1, 2 & 3 I'm hearing a clicking noise coming from the clutch when engaging the gear. After a few minutes, once it warms up, the clicking goes away.
I am @ stage 1+ W/VWR intake, but I'm not expecting clutch troubles from that.
Golf VI R :: Clutch Clicking / Popping Noise
Black 4 Door '13
37xx miles
Build date 07/12
No engine mods
I have had the clicking/popping clutch noise since I was breaking in the clutch but i thought it would eventually wear off. I have went through all the transmission threads and seen that a lot of people got it fixed having their clutch pedal assembly or master cylinder replaced.
Golf V R32 :: When AC Turned On Compressor Clutch Not Clicking
I have recently bought a R32 2008, and when trying to turn the AC I don't hear the AC compressor clutch clicking, the fans are running normally (radiator fans ). What should I check ? Someone told me that maybe it's a compressor problem, and another one said that if the refrigerant gas is low the clutch won't be engaged.
View 3 RepliesGolf IV R32 :: Clicking Noise During Idle / Goes Away When Press In Clutch
Just replaced my OEM clutch and flywheel with SPEC ones and now I have a weird clicking noise during idle from it. Noise goes away when I press in clutch. My technician says that they are known for this noise. Is that true?
View 6 RepliesGolf/GTI VI :: Clutch Clicking At Initial Travel / Wind Noise From Doors At Highway Speed
So far from reading up here is my list:
1) Water pump.
Its not leaking or making noise at this time.
2) Clutch clicking at initial travel.
Noticed this on the first couple miles.
3) Smelly A/C.
This is ongoing
4) Wind noise from doors at highway speed.
Noticed this also
5) Wastegate rattle
Don't hear any rattle, or I am not narrowing down the sound when it happens.
Anything else I should add?
TrailBlazer :: 2004 - AC Clutch Not Engaging
SYMPTOM : 04 Trailblazer had intermittent A/C clutch engagement with the A/C system fully charged (showed about 80lbs on low side with engine off)...
SOLUTION : Three wire plug that plugs into the A/C pump has a bad connection on middle pin. I chased the middle wire with a pick and pushed firmly, the A/C pump kicked in, and out when I released pressure.
Testing the Harnass side: with relay #44 crossed (pins 30 & 87), with vehicle on or off, and the plug attached, you should have 12V+ at dark green (middle wire), you should have a ground on the black or brown wire, and you should have approx. 5v+ on the Lt Green or yellow wire.
Testing the clutch side: (harnass unplugged)
Black to red 3.7 ohms.
Black to other red 3.7 ohms.
red to red .01 ohms (fully closed circuit)
- If red to red open circuit, you have a bad switch on the compressor body---replace compressor.
- If red to black open circuit, you have a failed electromagnet in your clutch, relace clutch.
- If compressor side tests good, and you are missing 5v+ on harnass side, you have a bad connection.
Sonata NF (2006-10) :: A/C Clutch Not Engaging
I'm having trouble with my a/c clutch not engaging now for about 4 days. I believe I have narrowed it down to the field coil. I checked and I am getting 14 volts at the wire that plugs into the compressor. Auto a/c function will not turn on the a/c compressor light on the dash, but will turn on when manually pushed. When this first started, the radiator fan would kick on but spin slowly and now does not turn on at all when engaging a/c.
Per an older thread I checked the resistance at the a/c relay, though it did not tell me which pin(s). The only readings in ohms I could find from the a/c relay junction in the engine fuse box said 69-76 ohms, but I am unsure whether I am reading the correct wires or the correct way. Facing the front of the car, I am getting the above ohm reading from the bottom right pin to ground. Which pin is the correct one to test?
I am currently thinking the a/c clutch field coil is bad, but it stumps me that the radiator fan will not kick on either now.
Background of car : PO wrecked car, damaging the front end. I bought the car and fixed it up. A/C Pulley was replaced due to bent flange where serpentine belt travels. Also brand new radiator fan and replaced other seemingly non-related items to this issue.
Santa FE SM (2001-06) :: AC Clutch Not Engaging - Low Gas?
I have recently purchased a 2003 Santa Fe 2.7 Auto and the air conditioning was not working. I noticed the compressor was not spinning so plugged a can of R134a into the low pressure port and noticed it had virtually no pressure. As per the instructions I filled the system until the compressor kicked in then filled it to near the optimum pressure (according to the temperature chart) of 45psi (it was probably nearer 40 as the can was running out).
The A/C was then blowing cold. However a few hours later when I tried it again, the compressor wouldn't engage. I haven't checked the pressure again yet as it was getting late but before I start looking into things I wanted to ask here if there are any particular common issues? I know on a Ford I had a few years ago I had to buy a smaller set of shims for the A/C clutch plate, is this the same with the Santa Fe?
I've read a bit about some connectors or switches but couldn't find much info. What would cause the compressor clutch to not engage when the A/C works well when it is engaged? As I say the pressure was about 40psi but I will check it again tomorrow, could it be it is a bit too low?