GTI 337/20th Anniversary :: Blow Off Valve On Stock 1.8T?
I wanted to get a blow-off valve for my GLI but its bone stock, i was wondering if its possible or if it would cause problems. and if i can whats a good brand?
View 17 RepliesGTI 337/20th Anniversary :: How To Reattach The Rubber Cover
My GTI has a problem i don't know how to fix. Shift knob on the automatic mk4 (2005) GTI, has a rubber piece that covers the ther gears when you are in the one of your choices. Such as if you were to be in drive then park reverse and neutral would be covered by the rubber sheet, as would the gears under drives such as the 4th 3rd and 2nd gears. That sheet of rubber on the car has been unattached from the front side of the sifter so that there is a hole in front of the shifter if I were in drive, the rubber piece that covers that hole was jammed into the front part of the gearbox (directly under the shift knob when in park).
I managed to get the rubber piece out from under there with a pair of very fine pliers. now my problem is how to attach the sheet back to the front of the shift knob. the rubber sheet seems to be very loose and when it is moved side to side you can see that there is some sort of zipper pattern along each edge of the rubber cover. MY QUESTION IS!! how to reattach the rubber cover?? or do i have to take that section apart and replace it?
GTI 337/20th Anniversary :: Efficient Way To Remove Stock Shifter?
So I have been looking but cant really seem to find an efficiant way to remove my stock shifter.
View 1 RepliesGTI 337/20th Anniversary :: Stock Crank Pulley Has A Dampener Which Keep Vibrating
So, yesterday I had my GLI in the shop to put a new timing belt on as well as some ECS Lightweight Pulleys. When I went to pick up the car, they did not install the pulleys. The reason they said was because the stock crank pulley has a dampener which keep vibration and balanced weight on the crank assembly and that the lightweight crank does not have these benefits.
So, now I have a set red anodized pulleys.. [URL].............
GTI 337/20th Anniversary :: Slight FW Chatter On Stock Clutch Setup
Getting a slight FW chatter on stock clutch setup (02M)? I've noticed it for a while...most of the time I don't notice it, but other times I will be sitting in the drive-through and it will chatter. Goes away when the clutch is depressed.
View 17 RepliesGTI 337/20th Anniversary :: Stock Suspension - Right Front Rubbing On Hard Turns?
I have a 20th with 106k on it and I notice mostly my right front rubbing on hard turns. Suspension is totally stock other than a 28mm rear sway. Is it possible that's causing it or is my suspension just getting old? No spacer on the fronts.
View 9 RepliesGTI 337/20th Anniversary :: Pedal Cover Came Off?
Can't manage to get it back on. Who knows the trick?
View 4 RepliesGTI 337/20th Anniversary :: Clutch Pedal Would Stick At 3/4 Of The Way Up
I recently got the GTI 1.8L 337 with 64,000 on it. It had been sitting, with daily start-ups, for about 8 months until the ALT was replaced. I've been driving it for a month with no problems until last week. At first I noticed the clutch pedal would pause on the way up for a split second then tap the bottom of my shoe. I thought maybe it needed adjustment but nothing serious. A few days ago the pedal would stick at 3/4 of the way up, and stay there most of the time unless I raised it with my foot, till the car warmed up a bit. Yesterday and today the pedal started to stick 1/4 of the way up, unless raised with my foot, at the morning start-up and will only come up 3/4 when warm. It also wont go into reverse at initial start-up until it gets really warmed up, shifting into other gears is fine. I've had no problems or real sounds shifting into any other gears, though out of 1st has been a little jumpy.
View 3 RepliesGTI 337/20th Anniversary :: Clutch Pedal Went Soft?
We were headed home the clutch pedal went soft... Ok, I thought it's either the clutch master or slave. I get it home and replace the master and after bleeding I had good pedal feel.
Great I thought, I got lucky and it was only the master. Drive it around for a bit and get on the highway and just as I was about to downshift the pedal went flat to the floor again.
Well after pumping the pedal until it had good feel again I got it home and bleed it a couple more times just to make sure I got all the air out. Drove it again. Same thing, after a little while the pedal gets soft again.
Now before I go and replace the slave is it possible I have a faulty master? Having issues after replacing the master?
GTI 337/20th Anniversary :: EPC Light Comes On And Gas Pedal Does Not Work
Car ran perfectly normal. come back out start the car, the EPC light comes on, and my gas pedal doesn't work. Doesn't do a THING...first 3 times i killed it and re-started it, the rpms shot up to 4500 for a second then fell to around 1100 and stayed there. now i start it and it just hangs at 1100. car has 47k miles on it, a 3in DP 2.5in magnaflow catback, short ram intake, TIP, 710N DV, stock N75. Only thing I can think of is TPS but I don't have access to a vag com.
View 2 RepliesGTI 337/20th Anniversary :: Clutch Pedal Trim Is Coming Off?
Noticed the other day my clutch pedal trim is coming off... What did you do to fix it?
View 8 RepliesGTI 337/20th Anniversary :: Clutch Pedal Is Soft At First And Then Gets Harder
I keep finding air every time i bleed my clutch. I am not losing fluid but i can not figure out whats causing my problems. The pedal is soft at first and then gets harder and it sometimes needs pumped before i change gears or to even get into gear. I am afraid its the slave but i also just may have air in the system.
View 8 RepliesGTI 337/20th Anniversary :: Clutch Replaced - No Pressure In Pedal
I just replaced my clutch and have put everything back together, and bled my clutch line, but I have absolutely no pressure still in my pedal. I read that u need to make sure your brake fluid reservoir is filled to the max, but following the clutch line, I dont see it going to the reservoir? I also read that the master cylinder is behind the clutch pedal, does the master cylinder hold any fluid that maybe I lost during the bleeding? I'm at a loss right now.
View 12 RepliesGTI 337/20th Anniversary :: Gas Pedal Feel Like Fluttering When Accelerate
When I Accelerate It almost feels like I am fluttering the gas pedal. Its weird on my car now I have revo stage 2, a TIP, 42DD TBE, 4bar FPR.. Do I need to buy a race n75 vavle ?
View 11 RepliesGTI 337/20th Anniversary :: Clutch Pedal Stuck In Place - Could Not Put It In Gear
So last night I was driving home from work, and at a red light while i was waiting to go i had my clutch down when light turned green i tried to go and noticed i could not put it in gear and that my clutch pedal was stuck in place. i didn't know what to do so I checked my shifter plate everything looked fine so went to look at the pedal and i pulled it forward and it came lose. I started it up everything was fine and back to order. This morning going to work same thing happened again, I don't know what is going on and what could be the cause?
View 5 RepliesGTI 337/20th Anniversary :: Jerking Under Acceleration When Hit Gas Pedal Slightly Hard
My 20th Ann. Is jerking under acceleration. When I hit the gas pedal slightly hard it starts jerking. Every once in a while the CEL will flash on and off. I changed the spark plugs and coil packs, cleaned the MAF, and now I have no real direction where to go. Maybe it could be a vaccum problem...
View 4 RepliesGTI 337/20th Anniversary :: Clutch Pedal Dropped To The Floor At The Stop
Coming to a stop, clutch pedal just lost all pressure. I can bring it back up, but even the slightest touch will send it to the floor again. I get the brake warning light on the dash. What could be causing this?
View 7 RepliesGTI 337/20th Anniversary :: 2003 - Zero Resistance When Clutch Pedal Pushed
My clutch has been feeling very strange lately, and has had a mind of its own. I have looked underneath myself, and have even taken it in to two transmission speacialists and they can't figure it out. The master cylinder isn't leaking, and the slave cylinder is fine as well.
Here's what is going on with my clutch...
- I will push in the pedal, and there will be ZERO resistance until about 1 inch from hitting the floor, then all the pressure is there, and I am able to shift. However, sometimes I won't even be able to put it into gear because the clutch won't engage.
- Then I will pump the pedal, and slowly I will gain a little more room on the draw of the clutch, and it will feel fine. All the way to the point where a few days later it will be driving like new.
- Then it will start feeling funky again a few days later and the cycle starts over.
I drive a 2003 GTI 20th AE.
GTI 337/20th Anniversary :: Clutch Pedal Goes From Being Soft To Very Hard When Close To Disengaging
I have an Imola 20th and recently i have been having some problems with my clutch. The pedal goes from being soft to very hard when its close to disengaging. It also engages very heavily when I go to let it out. This only started happening recently when temperatures started to drop if this has any effect on a clutch. Also, I replaced a shift fork two months ago and was curious if there was possibly anything going on with seals around the slave cylinder.
View 2 Replies