Ford Wiring/Electrical :: 1953 F100 - Oil Pressure Gauge Not Working
I'm about to dropkick my oil gauge but need to make sure that it is the problem. It WAS working but recently stopped. Here's what I have:
Dolphin electric oil gauge as part of their 6 gauge kit...fairly new oil sending unit (it's been on a year or so but the truck is not road worthy yet)....312 V8 and all of this is in a '53 F100.
I have verified, by hooking up a direct oil pressure gauge, that there is oil pressure. I have checked my wiring (it is all new from about a year ago) and it is all hooked up. My question is with the oil gauge removed, how can I hook up power to it and see if it works?
I could just go replace the sending unit but being that it is new I'm not going to throw parts at it just yet.
Ford Wiring/Electrical :: 1967 F100 - Instrument Cluster Gauge Wiring
I am a beginner when it comes to anything involving wiring. I am looking to re-wire all of the wiring coming off of the instrument cluster gauges. Once I have completed all of the wiring on the gauges, I may feel confident to move onto something else. As of rite now, it appears as though my truck is still running on all of the original wiring, and over the past few weeks, I have been having many wiring related issues. I found a schematic that includes the wiring for the gauges that I am going to go off of. I have a couple of questions before I begin.
1.) On the schematic, it shows connectors such as "Connector G" which is moving all of the gauges wires to there locations. Do I need to use a specific Ford connector, or could I purchase a new connector at any hardware store that carries them? As far as I am concerned, connectors do the same thing as all other connectors. (Let you connect and disconnect for easy instrument cluster removal.)
2.) I am not looking to purchase one of those expensive wiring harnesses. I would like to just purchase some wire that I can cut / use myself. What brand / type of wire should I be looking to purchase? I do not care if it is striped / colored as I will use wire tabs to name / label each wire.
Other than that, I feel confident enough to attempt something such as this. Here is the wiring schematic I am going to use.....
Ford Wiring/Electrical :: 1966 F100 - Ignition Totally Cut Out
Just got a 66 f100. Some one cut out the ignition. It has a toggle switch that doesn't seem to do anything, turned it to on and used a screwdriver to short the solenoid and it did not crank. I think I counted 9 cut wires in the area of the ignition counting 2 for the toggle. My other 61-66 trucks seem to just have five wires? So I can remove an ignition from one of these parts trucks, but might there be a difference since the gauges are unique to 1966 ?
Started to take the ignition out of my 62 f600 but i hate to cut wires but i must since there is no remnant of an ignition in the 66 f100. If I can match the five wires i should be ok. Just putting a battery in i have headlights, tailights and dash lights. Solenoid and cable to starter look horrible so i bought a new cable. I think i have a good solenoid or two? I didn't even get a spark when i shorted the solenoid with a screwdriver....
Ford Brakes/Suspension :: 1953 F100 - New Master Cylinder - No Pedal At All?
I have a '53 Ford F100. I have a PB conversion kit on it. The master cylinder & Booster are under the floor. I have used this setup for many years. Recently my master cylinder went bad. I replaced it with the same model. I bench bled it, and installed it. I also added a remote fill kit, since it's difficult to check & fill. Because of the booster, the master cylinder no longer sits under the hatch in the floor.
I got everything installed & connected, then bled all 4 wheels using a bleeder kit with an electric vacuum pump. The fluid runs clear & no bubbles, but I can't get a pedal by pumping. I have no leaks. I tried with the engine off, and running. I have felt soft pedals before, but I have no pedal at all, it just goes to the floor.
Ford Wiring/Electrical :: 1976 F100 - Engine Continues To Run And Only Way To Stop It Is To Jerk Coil Wire Off
I have a 1976 Ford F100 with a 302 and my problem is sometimes when my engine is running and I try to cut it off, it continues to run and the only way to stop it is to jerk the coil wire off. This is an intermittent problem. Happens about every 6 or 7 times I drive it. I have replaced the ignition switch and still have the same problem. Pretty sure it is some type wiring or ground issue, just need someplace to start.
View 1 RepliesFord Wiring/Electrical :: Headlights On And Radio Turns Off
I've been wondering about this issue for about a year now. I haven't torn out the stereo to see if the wiring is jacked up (came with the truck). When I have the truck running and the radio is on I pull the light switch and the radio turns off, then turns back on...... The radio also buzzes when the truck is running, kind of like it has a bad ground but I've checked the grounds and powers and all is good.
View 14 RepliesFord Wiring/Electrical :: Crank But No Start / Not Getting Spark From Coil
1996 Ford F150 5.0 ... New battery, new alternator, new starter, new coil, dis cap good and rotor is good. New plugs and wires. Ignition mod tested good.
Drove a mile from my house and lost power to my engine. Lights and radio work. Just sits there and cranks and cranks. I'm not getting spark from the coil. Don't know a lot about engines.
Ford Wiring/Electrical :: 2001 F350 Won't Crank - Batteries Draining?
My 2001 F350 Super Duty diesel keeps draining my batteries for some reason, wouldn't crank on Friday. Put my battery charger on for a few hours and it started fine. The rest of the day fired up fine, on Saturday it happened again. Had both batteries charged and load tested today, they are good. Short???
View 4 RepliesFord Wiring/Electrical :: 2008 F150 - Cold No Crank / No Start
I have an 08 F150 5.4L with about 68k miles. When the temperature is 40 degrees or colder it will not crank. I had the same issue with my 2005. I can turn the key and nothing, lights, radio and everything work. The dash display has dashes all the across for the miles, temp and compass. I have found out that it doesn't matter if I leave the key forward in the run position or try to crank, it won't do anything.
Battery is good and no problems with the truck. After the key is in and I give it anywhere from 15 to 60 seconds you can hear an electrical click real faintly and see the red security light come on and then the computer display comes on and then I can start with no problem? What could this be? My dealership has no clues and I can get it to act up because after I get it there it starts with no issue. The remotes work fine and this issue was why I got rid of my '05.
Starting - Electrical-wiring - Transmissions :: Nissan Maxima Cranks Slowly Then Turns Over But Doesn't Move
Just recently bought a 07 Nissan Maxima SE. Has a few issues.
The car sun roof does not work at all. It worked the day I bought it though.
Has issues turning on. Cranks slowly then after a few seconds of struggle it turns. Didn't have this issue when I bought it.
Goes idle when first starting to drive. From park, I put the car in drive, or reverse, and let go of the brake, it basically does nothing. Engine is on as if it were in park or neutral, but the car doesnt move. When I press the gas it takes a few seconds before it decides to actually move.
Ford Wiring/Electrical :: 2002 - Complete Headlight Switch Wiring Diagram?
Any COMPLETE headlight switch wiring diagram? Everything I find online only shows 2-3 wires in each sub connector, nothing with all wires and colors, and what they do. and of course the factory service manuals no longer work on my new computer. the switch and associated wires went up in smoke 2 hours ago, and this truck is my only means of transportation rite now. what i need is headlight wiring with colors so i can temporary hook up a toggle switch to have lights until the new switch and connectors come in next week. I went to pull the switch and connectors out of the parts truck, but of course that does not have fog lights so it uses different switch and connections.
View 14 RepliesFord Wiring/Electrical :: Moving Engine And Ignition System - Wiring Harness For Further Use?
I plan on moving the engine/drivetrain from my 1986 F350 460 to my 1996 F250. I also want to move over the 1986's ignition system with a Duraspark 2 setup.
Although I could just cut in the easiest places to remove the wiring for later reuse I am looking for where to make the cuts, what to take and what to scrap. Alternatively I am also asking if there are aftermarket or OEM replacement sets out there are aren't a ton of money. The current harness in the 1986 has been sprayed with engine oil and cooked for 27 years so I am looking at alternative options if there are any.
Ford Wiring/Electrical :: 1997 F250 - Rear Tail Lights Wiring
I have a 97 F250 HD. Wiring the rear tail lights. When we bought it the had cut off the wires going to both sides of the rear lighting assemblys and I was wondering what wire went to what i have the left turn signal working just can't seem to get the brake/back up light to work on that side and i can't figure out how to get the right side going either.
View 8 RepliesFord Wiring/Electrical :: 2004 - Instrument Cluster Wiring Diagram?
Looking for a source for a wiring diagram for the 2003/4 f350 instrument cluster, specifically the wiring/connectors to the gauges? A link to a PDF file would be nice. I would like to try and disconnect the PCM control to the transmission temperature and engine temperature and drive the gauges from my own sensors to bypass the non-linear behavior that ford decided was in our best interest. I am NOT interested in installing any more gauges, just want to control the ones already present with my own signals. It is possible that these gauges are all addressable devices on a common bus, instead of individual controls.
View 8 RepliesFord Wiring/Electrical :: 7 Pin Trailer Wiring - Running Lights Not Working
Just bought an 04 Super duty with the factory plug 7pin and 4 pin plug. Checked the fuses and finally tracked down the 2 relays under the hood but can't seem to find anything wrong. Everything on the trailer works except for the running lights. Is there another fuse or something I have missed? Trailer works fine on my buddies Duramax and worked fine on my old 97.
View 14 RepliesFord Wiring/Electrical :: 2004 - Installing Seat - Wiring And Functions?
Im installing a set of 04 lariat seats into a 00 truck. I need to know how to hook up the heat. The power part is no problem. What I thought was right which was a separate constant 12v and a switched 12v for the module and ground apparently isnt right. If somebody could ohm out their harness on a 01 truck that would be great. As I have it right now the light on the switch comes on but almost instantly turns off.
View 14 RepliesFord Wiring/Electrical :: 1987 F150 - Wiring Diagram With Carburetor?
Looking for a wiring diagram for a F-150 XLT LARIAT 5.8L 4BBL, all the books I have looked at show the wiring for this year with fuel injection and this truck came with a 351W with a Holley 600 4BBL, I have a few wire's in the engine compartment that melted away all the insulation, they are located close to where the harness passes the firewall before the ignition module. Is this a common problem on old models ?. Need a clear copy of the correct diagram for a f-150 1987 with carburetor, how I can get a copy so I can fix this problem before it gets worse.
View 3 RepliesFord Wiring/Electrical :: Wiring 2008 Seats In 2001 Model?
Let me start by saying electrical is something I really have no knowledge of....(never used any kind of an elec meter and don't have one) simple, Pos-grd and fuse, NP. I really don't want to fry something in these expensive new seats w/my normal trial and mostly ERROR!
The 08 (drivers) seat has 4 wires in the input clip.
GRN-RED (heavy gauge)
BLK-PURP (heavy gauge
BLU-RED
BLK-WHT
and my 01 whip out of the floor has a 3 wire setup.
GRN (heavy gauge)
BLK (heavy gauge)
BRN-BLU
I can wire PS side seat from fuse box and ground it NP. It only has a 2 wire set-up in the new seat.
Ford Wiring/Electrical :: 2000 - Electric Shift Transfer Case Wiring Diagram?
I am curious if it is possible to make a stand alone controller for the electric shift transfer case in a 2000 F-350?
The reason I ask is, this is swapped into a 4x4 conversion in a van and I would like the transfer case to work like the factory, but I don't want to swap over the whole GEM module. I have the high to low and low to high shift relays and wiring, the selector switch from the dash.
I know that powering up the relays will shift the transfer case, but the GEM module tells when the relays need to shut off, and that is where I am not sure what to do. I am assuming that the other plug on the shift motor (6 pin plug) is the sensor that tells the GEM module where the shift is at.
What needs to be done (with a bank of relays).....