Ford Transmission :: E40D - Shifts Very Hard From 1st To 2nd / Light Flashes On Overdrive Button
My tranny started acting up so I took it to a reputable transmission shop for repair.
Symptoms : Shifts very hard 1st to 2nd. Light flashes on overdrive button.
The following is what has been done at the transmission shop.
Computer failed to read codes. Sent out to rebuild. After rebuild, codes read FIPL needs replace. Done and gives good readout. Trans control replaced, speed sensor replaced, checked all associated wiring and plugs as well as ground. Dropped pan, changed fluid and filter. No parts in pan. Tech says pan and fluid looked good. Replaced coil pack.
After all that, this is what is happening..Clear all codes. FIPL reading good. No flashing light on shifter. It feels like it is shifting from 1st to 3rd, then back to 2nd. Still shifting hard and indicator light starts blinking again. He is going to read computer again. At this point, he suspects a mechanical problem in transmission but is reluctant to remove and tear down.
Ford Transmission :: E4OD - Hard 2 To 3 Shift Caused By Slow 1 To 2 Shift?
This is on my 7.3PSD. I've observed that the 1-2 gear shift drops about 1,000 RPMs and takes a good half second or longer to do so when given a lot of accelerator pedal input. And then the 2-3 shift is a very quick and harsh shift.
If I am accelerating gently the 2-3 shift is as unnoticeable as the 1-2 shift is quick. Is the slow 1-2 shift causing the trans to protect itself and affecting the 2-3 shift? And if so, what do I do to resolve all of this? I changed the trans fluid a week ago and there is no change.
Ford - Focus :: 2001 - Brake Pedal Feels Hard / Transmission Hard To Shift From 1st To 2nd Gear
Could my brake issue be related to my transmission problem? Neither are constant. Brake problem= sometimes the brake pedal feels hard, like there's no power brakes (I drove a car once. ..looong time ago. .. that had no power brakes or steering) but it will kick in after a short distance. Transmission prob= seemingly unrelated, is a problem shifting from 1st to 2nd gear. This has happened maybe a 1/2 dozen times, the first time and mostly when in heavy commute traffic and when going between 1st and 2nd gear because of the slow commute speed, but also at other times when not in lengthy slow commutes. When it doesn't shift, the odometer doesn't work (shows only dashes) and an engine light comes on (the sprocket/gear looking one). Usually the transmission will eventually shift and the light goes off.
I read that the brake problem might be a vacuum hose problem? Something about a booster? Is this dangerous? or is it like having a car w/ no power brakes? Going to have my transmission looked at this week. Read on another site about dropping valve seats on this year car. If there's a major transmission problem, I'm wondering if it's worth fixing? I changed, timing belt, water pump, front and rears brakes, tires. 143,000 miles.
Ford Transmission :: 1995 E40D - No Forward Gears
Had tranny fluid and filter replaced a couple months ago. It's in a 35 foot motorhome (F53 chassis). The motorhome is within it's GCWR. Climbing a 6% grade at 3,500 rpm, little more than half throttle, like all the other climbs. 80 degrees out. Engine temp was on the letter "R" on the word "NORMAL". All of a sudden my engine redlines as if it popped into neutral. I let off, put it into neutral, and try "D" again. Nothing.
At this point it's uphill so it's naturally slowing down and I try "2". Nothing. Even slower and I try "1". Nothing. Pulling over blocking the right lane on a blind curve on a grade is scary. Had pylon cones out, waving traffic to warn them down a ways, etc.
No fluid on the ground, no slipping prior to this. I have reverse. I see no obvious linkage or electrical/wire issues underneath (from road debris, etc). It's at a shop but I want to know all I can so if they come back with something outrageous I can make a decision. I never pulled the stick, as I was coordinating traffic, highway patrol, a tow truck, etc.
Ford Transmission :: E40D - O/D Light Will Flash But Still Operate In All Gears
I have a 96 Ford f super duty with a 7.5l and E40d after about 30minutes of driving O/D light will flash but still operate in all gears. Pulled codes and got 628 excessive converter clutch slippage and 657 fluid over heated. Now I have not felt a shudder which would indicate slippage like my 91 ford E40d does on lockup. And the temp never got above 210 until the light started flashing or I came to a stop. and front seal leaks also which in a tsb a read of another forum claimed that leaks can cause that code. I have already replaced solenoid pack after it got fried when the problem started last Monday...
View 14 RepliesFord Transmission :: 1992 E40d Starts Downshifting Only Under Heavy Acceleration
Ok long story short I was given a conversion van that is built on a e150 van and has a 5.8 liter with an e40d tranny.. This van sat for at least 3 years till recently..
I have cleaned all electric connections on the tranny and the one on the rear differential . New filter and fluid but did not drain the converter after driving it for about an hour we finally got it to start shifting gears automatically the problem is it wants to shift only under heavy acceleration and then only to second at about 35 mph and drive at about 60 mph and over drive around 80 mph and all this only under heavy acceleration you let of the gas a little and it starts down shifting..
What I may look for next that may be pretty easy to try. My thoughts at this point are maybe the torque converter is going south but I am hoping for a more simple solution..
Ford Transmission :: E40D - Rough Shifting From 1 To 2 Gear / Whole Truck Shudder
My 1992 F-250 7.3 4X4 has a very intermittent issue with the E40D. Rarely, usually after a lot of around town driving (I don't know if that has any direct correlation), I will get a rough shift from 1-2. It will kind of bang into gear and make the whole truck shudder.
On one of it's episodes, it also did it in 2-3, however that only happened once and I haven't been able to make it do that again. I'm worried that it's something that I should address, if I can do so without just rebuilding the whole transmission. It doesn't slip and shifts fine most of the time, other than the occasional 1-2 issue.
To cut this short, does this sound like a 1-2 accumulator issue? Maybe just old truck syndrome? I feel like this is a dumb as hell question, but isn't it a bad idea to install a shift kit in an E40D with 126K miles on it?
Ford F-150 (2009-2014) :: Transmission Hard Shift Between 1st And 2nd Then Again Between 2nd And 3rd
2011 F-150 Scab 5.0L 25k miles. Why my transmission is waiting several seconds after being placed into drive or reverse before it actually slips into gear when first started in the morning and why it has a hard shift between 1st and 2nd than again between 2nd and 3rd and maybe why when it shifts into 2nd and 3rd gear it slips back out than back in?
View 7 RepliesFord Transmission :: 4r100 Hard Shift After Rebuild
I have a e99 7.3. had the transmission rebuilt a couple weeks ago by a local shop. have been getting some hard shifts between 2nd/3rd when lightly accelerating. Took it back already but they couldn't find anything. I am planning on taking it back again but what it is so it gets fixed right. What is causing this or what it might be? Should I be worried about having this shop try and fix this?
View 1 RepliesFord Transmission :: Hard Shift And Clunk When Shifting To Reverse
I just recently bought a 95 F150 with a 351. The truck has high mileage, about 190k, and I am not sure how long the transmission has left. It rides smooth down the road, but when I put the truck into reverse it hesitates for a moment then makes a loud clunking sound(as if a door is being slammed) and then jerks into gear. The reverse works great at the moment though. Should I be worried, is there anything I can do to fix this?
View 11 RepliesFord Transmission :: 1993 - Manual Hard Shift When Warm?
I'm trying to diagnose a problem with my dad's 93 F250 7.3 diesel 4x4 with a ZF S5-42 5 speed manual transmission. It seems to not want to shift back into gear once the truck has warmed up, with 1st, 2nd and reverse being the toughest gears to get into. We've done a transmission fluid change with the required dextron/mercon substitute but the problem existed before the change and the change didn't seem to solve the problem any.
This problem didn't exist until I did a couple hundred miles of towing with it, some of which was done in 5th gear (overdrive?), so I'm hoping the 5th gear towing didn't ruin the transmission. From a cold start the transmission has no trouble shifting into any gear as well as with the engine off when either warm or cold, but with the engine idling and the truck at operating temperature it can be difficult to impossible to shift into gear, especially reverse.
I think heat has something to do with the problem because the shifts were worse a when its driven longer and during the tow/driving that was done in the last part of summer. It sat most of the time since then but we took it out today to test some things. Hot or cold the external hydraulic slave had roughly the same range of movement, but the drive line seems to jerk more noticeably like power is applied to it during a shift when its warm.
This all makes me think, even though the clutch hydraulic system is working like I think it should, that the clutch is not fully disengaging when at temp. I'm not a transmission guy so before I start throwing parts/labor at a problem.
Ford Excursion :: Hard To Shift - Transmission Lever Coming Out
As it turns out, my shift cable wasn't bad. The transmission lever coming out of the transmission doesn't want to move very easily. When in gear, it shifts fine as it should, so I'm thinking something is bad with the lever. Problem is, I don't know what could possibly be causing it.
View 8 RepliesFord Transmission :: 2005 - Engine Revs Up And Hard To Shift From 2nd To 3rd
I have a 05 expedition and when it goes to shift from 2nd to 3rd the engine revs up and shifts hard all other gears shift fine. What can this issue be and is it a easy fix?
View 1 RepliesFord F-150 (2009-2014) :: V8 Transmission Hard To Shift At Highway Speeds
I have a 2014 screw 4x4 v8 that has been in the shop 5 times now for something that the dealership can't duplicate, and that is intermittent enough for me that I can't determine what the conditions need to be in order to duplicate it myself.
My transmission will shift hard under two different situations:
1) when rolling through a stop, or a momentary stop at a stop sign, the transmission holds up between 3 and 1, and when I bring the rpms up, the transmission shifts down into 1, making a hard clunk;
2) at highway speeds, more so when using cruise, if I accelerate and the truck shifts down from 6 to 4, there will be a hard shift as well. In fact, when I'm on a long stretch of flat, open road using cruise at 70-75, I can feel a slight bump through the steering wheel and floorboard, as if the cruise is trying to engage the throttle a bit more, but only for a split second. But that will happen quite a few times within a couple miles until I come up on a grade and the throttle has to engage for a bit longer to keep speed. Sometimes, the hard shift will do occur going to 5 as well, but 90% of the time it will be a 6-4 shift. If the truck decides to shift from 6-3, there's no issue and it shifts and accelerates like it should.
Again, this is so intermittent, but when it happens, it happens several times. I've had the service tech ride in the truck with me, all the while not being able to duplicate the issue. I understand that these are learning transmissions, so the only thing I can think of is when I try to duplicate it by accelerating over and over, that the transmission adjusts the shift pattern or fluid pressure to compensate.
Ford Ranger / B-Series :: 2003 - Hard Shift - Transmission Or Clutch?
The truck: 03 Ranger, 2wd, 2.3L, 5spd, 160k mi
I bought the truck two years ago and it's always been difficult to shift (especially into 1st, 2nd, 3rd). I don't drive it often and only put 5k mi on it since I bought it.
The problem: Someone more mechanically inclined than I once told me that the hard shifting is probably due to the clutch not fully releasing due to low hydraulic pressure brought about by a failing slave cylinder.
I just noticed today that there is a high-pitched squeaking coming from somewhere on the truck. At first, I thought it was the rear end, but now, after pulling it into the driveway, I noticed that the squeaking noise vanishes when I push in the clutch pedal and returns after I release the clutch pedal and drive in 1st gear.
The transmission oil level is good, but I've never changed it and I'm not sure if the previous owner ever did either. I'm hoping I haven't damaged the transmission.
After reading a few threads, it seems the problem might be the input shaft bearing. To replace it, I'd need to drop the transmission and borrow a couple of tools I don't have (feeler gauge and bearing puller). If the ISB is the problem, it seems like it would be a good idea to change it now before it seizes and leaves me stranded somewhere.
Ford F-150 (2009-2014) :: Transmission Exhibit Extremely Hard And Abrupt Shift Every Now And Then
Starting to develop an issue where the trans will exhibit an extremely hard and abrupt shift every now and then - most only during the first couple hundred yards of driving and I think its the 1-2 shift. Only will happen once and only rarely but its becoming more frequent. I have an '11 5.0L supercab auto 4x4, but my father has a similar truck but with the ecoboost which does the same thing on a MUCH more frequent basis. He has been in numerous times with no resolution so I am loathe to expend the energy on "dealing" with them.
View 12 RepliesFord Ranger / B-Series :: 2000 / 4R44e Transmission - Hard Shift From 2 - 3 Gear
2000 Ranger 4R44e transmission.Hard shift from 2-3 gear and when i run about 35-40 mph and brake then acelerate it downshifts hard . Whats wrong with it?
View 14 RepliesFord 6.7L Power Stroke Diesel :: Automatic Transmission Hard Shift Second Gear
Well I've been towing for almost 150,000 miles with a 2012 6.7 Lariat 4 wheel drive. Things have been going pretty well with the truck. I noticed some sluggish and indecisive type shifts early on but now I'm worried. I depend on this truck for pulling a horse trailer all over the country and Canada. Just recently I've been getting a hard shift or a thump or a clunk when shifting up or down in to second gear. I'm at about 152,000 miles and did a hot flush with LV ATF at about 148,000 miles. Should I worry or keep running?
I have a 97' PSD I'm thinking of giving a nice paint job and a flat bed but am reluctant to do so due to financial concerns and the fact that some folks may not want to see me pull up in an old truck no matter how nice it looks. My tranny temps have been stating under 200F and I really keep an eye on the temps when running up and down the hills while towing. The trailer is a 35' Gooseneck with a max GVRW or 14,000 pounds. Should I wait for the tranny to grenade and then drop in a built tranny and if so who's building these tranny's stronger than stock? Long time no see but this site has always been my go to for all my Ford truck questions, upgrades, etc.
Ford Super Duty (1999-2016) :: 5R110 Transmission Would Suddenly Hard Shift
I have a 2005 Ford 6.0L Diesel with the 5R110 transmission.
About a month ago, i started seeing some strange shifting issues with the transmission. While driving normally, it would suddenly hard shift (slam itself into gear), the entire truck would shake it shifted so hard. It would also cause the Tow/Haul indicator to start blinking. (my understanding is that the Tow/Haul light indicates an error code).
I drained/flushed the transmission, installed the larger pan/with the improved filter. I put Mercon LV back into the transmission (what type of fluid was in there before).
The problem still persists, and got a bit worse. The truck is almost un driveable at this point. Still getting Tow/Haul flashing messages. Can the error code be read by an standard ODB2 reader ?