Ford Super Duty (1999-2016) :: Conversion Of Leaf Spring To Coil Spring?
Conversion from the dana 50 to the newer dana 60 with coil spring? My Dana 50 has called it quits so while my front end is already off the vehicle already why not make improvements. Ford used the 50 for 1999 to 2002 then upgraded to the 60, I'm guessing it was for a reason!
I've read this article on a similar project but the dana 60 had leaf springs as well: Dana 60 Conversion for F250 years 1986-1996 .: Articles I'd prefer coil spring, nothing more then personal preference with a bit of better ride quality. The donor vehicle is a 06 SRW F250 This is not what I'll be getting but just as an example of the parts I would get.
Ford Super Duty (1999-2016) :: 2002 - Driver Side Front Leaf Spring Snapped?
I just realized my driver's side front leaf spring on my 2002 F250 has snapped. I checked the weight sticker on my truck and it weighs 5200lbs in the front. My question is the heaviest springs I found only support 2630lbs a piece, so being a 7.3 is 5200lbs a correct weight for the front of this truck? also why would Ford make springs that support only 60lbs more than the front weight? Hell I weight more than 60lbs.... Did I snap the damn thing just by climbing into the cab?!?!
View 6 RepliesFord Super Duty (1999-2016) :: 2000 F350 - Front Passenger Leaf Spring Just Broken
My front passenger leaf spring just broke on my 2000 f-350. My front springs are T code, but I was wondering if a could replace the broken one with a code X spring as a temp fix until I get a leaf spring replacement delivered?
View 1 RepliesFord Super Duty (1999-2016) :: Speed Nut For Rear Leaf Spring
Where I can get or have a speed nut for the front eye bolt of the right rear leaf spring? If you do I'll gladly send you some cash for it and to cover shipping it. It's supposed to rain pretty much all week here and I really don't want to go to a junkyard. I have checked ford parts and nothing there you can get the hanger that attaches to the frame that the spring bolts to but not the speed nut or bolt only need the speed nut though. Truck is an 2004 f-250 so 1999-04 will work and 05 to 07 is setup the same in the rear but I don't know if they are the same size bolt since they made the frame heavier. I have no idea after 07 when they made the springs longer.
View 1 RepliesFord Super Duty (1999-2016) :: Replacing Rear Block - Axle Won't Separate From Leaf Springs?
I decided to go ahead and do a rear block replacement. I'm going to install the Ready lift 4 inch blocks.
I have both u bolts and nuts off of both sides. Rear stabilizer bar disconnected and both shocks disconnected. However, when I raise the rear of the truck, the axle raises as well. What could be holding it on still? I noticed there's a nut in the middle of the leaf springs. Do I take that nut off? I just don't know what could be keeping it from separating.
Ford Super Duty (1999-2016) :: 2000 F250 - Clunk In Front / Leaf Springs Bad?
As the title says are my front leaf springs bad? I got this truck 2 years ago and replaced all the ball joints, shocks, sway bar links,front hubs, rotors and brakes along with all the seals. I have a clunk in the front and I can't figure out what it's coming from. Could my leaf springs be clacking together? Truck
is a 2000 F250 SD v10.....
Driverside front
Rear spring
Ford Super Duty (1999-2016) :: 2004 F250 - Tire Rubbing On Plastic And Front Leaf Springs?
I just put some toyo at2 295.75.16. On my 04 250. And I've got some rubbing on the plastic and front leaf springs. If a 2.5 " spring left will take care of the rubbing or will I need wheel spacers.
View 3 RepliesFord Super Duty (1999-2016) :: 2003 F250 - Front Tires Leaf Springs Rubbing Even On Slight Tight Turn
I got an 03 f250 with a 10 inch lift on 40x14.50 tires on 20x10 fuel hostage wheels. They rub my springs pretty bad when trying to make even the slightest kind of tight turn and the sound they make when they rub is even worse than them actually rubbing. My question is should i stay with this tire and wheel setup and try to get some 6061 billet aluminum 2 inch spacers? (I'm not sure about going that route though because of what i heard about spacers) or go down to some 38s with a 20x14 wheel that hopefully would push the tire away from the hub like spacers would do. I'm leaning more towards going to 38s because of the rubbing and also because I feel they might look better on the 10 inch lift rather than the 40s but dont know whats the best thing to do.
View 12 RepliesFord Super Duty (1999-2016) :: F250 - Front Spring Spacing?
I am looking at a set of SD axles for my 92 F250. I have been looking for the last 2hrs and have found measurements for seemingly every axle in existence except for the SD D50/60.
What the center to center width is on the spring pads of the front axle. Wouldn't hurt to know the same measurement for the rear either.
Also, a bit more trivial, but still need to know, what is the size and taper of the draglink joint that goes in the pittman arm.
Ford Super Duty (1999-2016) :: 2003 - Clock Spring Has 8 Spring Wire?
Adding cruise control to F350 XL I just bought. I got a steering wheel with the buttons. But I am having problems with the clock spring. Mine has an 8 wire plug with only 6 pins on the big plug and all of the clock springs I have found have only a 6 wire plug for the big one. Without changing my clock spring I have no where to plug in the cruise wiring. All have been for right year model with cruise and even tried different years but none will plug in under the dash.
View 3 RepliesFord Super Duty (1999-2016) :: 2015 - Front Axle Leaking A Lot?
I have a 2015 F250, cc 4X4 PSD. It has 22,000 miles on it. I notice a small quarter sized drop of oil after it is parked by the right side front wheel. It is coming from behind the dust cover and universal joint where the axle goes into the tube. I dont know how long it has been leaking. My issue is I am about 800 miles from home on a camping trip, have to go back to work Monday, and lcoal dealer here can't take it in till next week. So, if the hubs are not locked and the truck is in 2 wheel drive, the gears shouldn't be turning right? I assume it is ok to drive home. I didn't want to pull the plug and check the fluid because if any runs out and leaves a stain on the cover, I don't want ford trying to deny warranty claiming I messed with it first.
View 5 RepliesFord Super Duty (1999-2016) :: Leak In Front Axle Shaft
Check out the pics. 99 f250 4x4. I have a leak in my front axle shaft. It looks like it is coming out of the dust cap on the end of the front shaft. I am pretty sure it is differential fluid from the smell. Is there a seal before the dust cap? Is the shaft hollow with fluid in it? I thought it was just in the differential and if it leaks it is at the seals where the axle goes into the differential not at the otter end.
View 2 RepliesFord Super Duty (1999-2016) :: Clicking Noise From Front Axle
I have a slight problem and don't know how serious it is. I own a 2003 F350 with a lift kit. After my drive shaft shattered last September. due to a U-Joint a clicking noise started up in the front axle area after we locked the hubs so we could crawl it down the road out of traffic.
What would be the likely causes and how much would a typical repair/replace cost?
Ford Super Duty (1999-2016) :: Front 4x4 Axle Still Turn When Unlocked
I am not up on the exact operation of the hub lock/unlock on superdutys but when following them, I can see the front axles still turning with the wheel. So even with them "disengaged" they still turn with the wheels?
If that is the way they are designed to do, why? Seems like efficiency could be gained by having them actually disengaged when not needed. And save wear on the inner housing seals.
Ford Super Duty (1999-2016) :: Front Axle Seal Leaking?
I noticed the other day after my truck was parked on a bit of a angle there was diff oil from the passenger side on the ground. reading a bit on here i learned the axle seals are way in the front housing close to the front diff. and yesterday driving a heavy load around my front brake driver side got stuck on a bit and over heated and was smoking, couldn't even touch the rim it was so hot. anyway about this axle seal i got the hub off right now but cant seem to pull out the axle assembly through the knuckle but i see i have to pry and most likely wreck that seal. Looking for a link of piuctures or how to replace the axle seals in the housing.
View 11 RepliesFord Super Duty (1999-2016) :: 2006 - How To Tighten Front Axle
It's the Right Front Axle Shaft on my 2006 F250 where it goes into the Hub/Bearing assembly.
Seems way to loose to me but after I removed the Lock-Out, I discovered the Axle Shaft is held in by a Snap-Ring not a Nut (WTF) so how do I get this tightened up
Also it's my understanding (I didn't remove) between the Axle & Steering Knuckle there's a rubber O-Ring. Could all this play be from that O-Ring being wasted Although that doesn't seem likely to me, Iam worried what's wrong
Ford Super Duty (1999-2016) :: Front Axle Shaft Wiggle
So the other day I took my locking hubs out and cleaned them really good. When they were out I noticed I could grabs axle shafts inside the hub and wiggle them quiet a bit. Is that normal?
View 2 RepliesFord Super Duty (1999-2016) :: Front Axle U-Joints Rusted
I have my front axles out to replace the U-Joints but they are rusted in there. Even the C-Clip is fused/rusted in place. I use my flat wheel grinder and ground out the C-Clips but the U-Joint caps wont budge. Been soaking in penetrating oil too. Any way other than drilling them out?
View 1 RepliesFord Super Duty (1999-2016) :: 2005 - Oil Leak From Front Axle?
I have an F250 4.2 diesel 4x4 double cab. Its a2005 model. I noticed an oil leak from the front left axle. It looks like its leaking from the axle tube. See pic attached. Is a seal probably worn? How big a job is this to fix.
View 4 Replies