Ford Super Duty (1999-2016) :: Spacing On Rear Leaf Springs?
I have a 99 SD 250 diesel, I also have a broken rear leaf spring. My truck has a 3 1/2 in. block between axle and leaf. My question is this. Can I remove the block and install 4" lift leaf springs without messing up my pinion angle? The blocks look square. But someone toldme once they are made to a specific angle for rotating pinion for better u joint alignment. Sounds like it could be true.
View 9 RepliesFord Super Duty (1999-2016) :: 2003 2WD F250 Coil Spring Retaining Bolt Won't Budge
So I went to install a front end leveling kit in my 2003 2WD F250, looked like a simple task, except the bolt that holds the lower coil spring mount won't budge! I tried heating the nut, I soaked it with WD-40, tried a 200lb impact and a 30" breaker bar with all my weight. Is there something I am missing?
View 5 RepliesFord Super Duty (1999-2016) :: 2003 - Clock Spring Has 8 Spring Wire?
Adding cruise control to F350 XL I just bought. I got a steering wheel with the buttons. But I am having problems with the clock spring. Mine has an 8 wire plug with only 6 pins on the big plug and all of the clock springs I have found have only a 6 wire plug for the big one. Without changing my clock spring I have no where to plug in the cruise wiring. All have been for right year model with cruise and even tried different years but none will plug in under the dash.
View 3 RepliesFord Super Duty (1999-2016) :: Conversion Of Leaf Spring To Coil Spring?
Conversion from the dana 50 to the newer dana 60 with coil spring? My Dana 50 has called it quits so while my front end is already off the vehicle already why not make improvements. Ford used the 50 for 1999 to 2002 then upgraded to the 60, I'm guessing it was for a reason!
I've read this article on a similar project but the dana 60 had leaf springs as well: Dana 60 Conversion for F250 years 1986-1996 .: Articles I'd prefer coil spring, nothing more then personal preference with a bit of better ride quality. The donor vehicle is a 06 SRW F250 This is not what I'll be getting but just as an example of the parts I would get.
Ford Super Duty (1999-2016) :: 1991 F250 - Heavy Camper Back Spring Flattened Out - Put Airbags?
I have a 1991 f250 that used to have a camper on it, I recently got this truck and when I put an older heavy camper on it the back springs flattened out and the front raised about an inch or two.
My question is...I am going to put air bags on this truck to alleviate this problem, should I replace the springs as well or will the air bags be sufficient to handle a camper?
Ford Super Duty (1999-2016) :: 2002 - Driver Side Front Leaf Spring Snapped?
I just realized my driver's side front leaf spring on my 2002 F250 has snapped. I checked the weight sticker on my truck and it weighs 5200lbs in the front. My question is the heaviest springs I found only support 2630lbs a piece, so being a 7.3 is 5200lbs a correct weight for the front of this truck? also why would Ford make springs that support only 60lbs more than the front weight? Hell I weight more than 60lbs.... Did I snap the damn thing just by climbing into the cab?!?!
View 6 RepliesFord Super Duty (1999-2016) :: 2000 F350 - Front Passenger Leaf Spring Just Broken
My front passenger leaf spring just broke on my 2000 f-350. My front springs are T code, but I was wondering if a could replace the broken one with a code X spring as a temp fix until I get a leaf spring replacement delivered?
View 1 RepliesFord Super Duty (1999-2016) :: Width Between The Spring Perches On Leaf Sprung Front Axle?
What is the width between the spring perches on leaf sprung 99-04 front axle. I searched and cant seem to find a dimension listed anywhere. i tried the dana60 bible on the pirate site as well, but it doesn't list the spring perch dimensions, only for the pre 99 styles
View 2 RepliesFord Super Duty (1999-2016) :: Little Wire Spring That Applies Pressure For Brake Pads On Front Disc Brakes Lost
My 18 year old launched the little wire spring thing that applies pressure for the brake pads on front disc brakes. Could have gone in to neighbor's yard! Actually lost one on each side. He put it all back together without one on each side. I said it would still work fine. What's the deal really? Can't be that important are they?
View 14 RepliesFord Super Duty (1999-2016) :: F250 4x4 - Front Radius Arm Length
I trying to find the distance/length of a 2005 4x4 onward front radius arm. I'm fitting a 2004 Cummins nv5600 and transfer case into a 1997 fzj80 Landcruiser. I'm also fitting front and rear diff/axles from a 2008 f350 however don't have the radius arms and late model f250 are extremely rare birds here as Ford don't sell them here. I want the distance from the rear bush in the radius arm(at the chassis) to the front bush (top and bottom) at the diff/axle....
View 1 RepliesFord Super Duty (1999-2016) :: F250 - Front Bumper Bent?
I bent my front bumper. Every time I look on amazon or ebay , when I put in my year, model, engine, it says their bumper won't fit. Mine has the 3 rectangular openings, 2 have the holes for mounting and tow hooks. It is chrome with the gray plastic or rubber bottom.Xlt. Also what part is the valance?
View 7 RepliesFord Super Duty (1999-2016) :: F250 LD Front Brakes / Rotors Won't Come Off
was going to do a brake job on my f250 light duty and the rotors won't come off. At first I thought they were rusted on but after looking at them it looks like the studs are attached to the rotor. Need to confirm this because the new rotors I got don't have the hub attached. Don't know if it's the wrong part or what?
View 9 RepliesFord Super Duty (1999-2016) :: Speed Nut For Rear Leaf Spring
Where I can get or have a speed nut for the front eye bolt of the right rear leaf spring? If you do I'll gladly send you some cash for it and to cover shipping it. It's supposed to rain pretty much all week here and I really don't want to go to a junkyard. I have checked ford parts and nothing there you can get the hanger that attaches to the frame that the spring bolts to but not the speed nut or bolt only need the speed nut though. Truck is an 2004 f-250 so 1999-04 will work and 05 to 07 is setup the same in the rear but I don't know if they are the same size bolt since they made the frame heavier. I have no idea after 07 when they made the springs longer.
View 1 RepliesFord Super Duty (1999-2016) :: 2002 F250 2wd Leveling Kit - Front End Sagging So Low?
I recently purchased a 2002 F250 Regular cab long bed 2wd. I'm tired of the front end sagging so low, so I've been looking into a leveling kit. I was wondering whether I should go with 2" or 1.5" for the kit. I tow about 2000 lbs. 3-4 days a week and do not want the truck to look like it is squatting too badly. However, I really would like it too look more level.
View 8 RepliesFord Super Duty (1999-2016) :: 2013 F250 - Changing Front Springs?
I just bought a used 2013 F-250 4x4 and it came with the snow plow pkg. heavy duty front springs. I love the truck, but won't be plowing with it, and I don't need the rough ride (and don't like the look of the front end higher than the rear)
How hard is it to swap out the front coil springs and replace them with the "regular" ones?
Ford Super Duty (1999-2016) :: 2014 F250 - Front Bumper Sagging
I got a 2014 F250 SD w/ 6.7 diesel. Since if owned the truck the front bumper has slowly started to sag at both driver and passenger side. Dealer says there is no adjustments for it.
View 14 RepliesFord Super Duty (1999-2016) :: 2010 F250 Front Hubs Don't Lock
I have a 2010 F250 with 154000km (96000 miles) that we bought last week. When I was looking it over during the purchase I noticed the front axle didn't lockup in "auto", in manual lock it seemed fine so I figured vacuum leak or something like that. Yesterday morning I was in the yard and got a little hung up in snow drifts so just got out, locked the hubs and switched to 4x4 and I think the front end didn't engage at all.
So later on I had it in the shop installing the two way radio and decided to check the front end out a little more thoroughly. Vacuum lines seem fine, hubs turn fine but I notice the axle shafts both move up and down almost a quarter inch, that seems excessively loose to me. I've been doing some research on the internet and it appears the front hubs are serviced as a unit, also some information seems to point to needle bearings within the actual locking hub mechanism itself?
So the questions:
1. Does that front axle shaft seem excessive? What are the specs?
2. Can I replace bearings and seals only or do these units come only as assemblies? Inner hub, outer hub units? Wheel bearings seem fine.
3. With that much play is there a chance the outer axle shafts are worn also?
Ford Super Duty (1999-2016) :: F250 - Leak In Front Axle Shaft
Check out the pics. 99 f250 4x4. I have a leak in my front axle shaft. It looks like it is coming out of the dust cap on the end of the front shaft. I am pretty sure it is differential fluid from the smell. Is there a seal before the dust cap? Is the shaft hollow with fluid in it? I thought it was just in the differential and if it leaks it is at the seals where the axle goes into the differential not at the otter end.
View 14 RepliesFord Super Duty (1999-2016) :: 2004 F250 4x4 - Strange Noise From Front End
In the last few hundred miles of driving, I notice there is a strange noise coming from what appears to be the front end of my truck. It sounds similar to a buzzsaw or a power sanding tool whenever it comes in contact with an object. The noise starts at around 30 mph, stops from 55-60mph, and starts again around 65 mph. The truck rides and drives normally and there doesn't seem to be any metal to metal contact noises or clunking and the hubs dont seem to be hot to the touch. I was thinking improperly balanced tires, wheel bearing, or front carrier assembly. What it could be? The noise just suddenly started and I was wondering if I should keep driving it?
View 7 Replies