Ford F-150 (2004-2008) :: Code P0022 - Intake Camshaft Position Timing-over-retarded Bank 2

Driving around today my cel flashed on. Checked my programmer its saying P0022 intake camshaft position timing-over-retarded bank 2. What is the culprit?

View 2 Replies

Lexus RX 2004-09 :: Error Code P0015 / Camshaft Position - Timing Over Retarded (Bank 1)

A week ago I was traveling in my wife's 2009 RX350 at freeways speeds and outside ambient temperatures around 80 degrees. After traveling about 2 hours and stopping for about half-hour for lunch, I started the vehicle and went around a mile and the Check Engine light came on, the VSC was flashing and the traction control indicator was illuminated. I stopped quickly in a gas station and checked the manual for what the warning lights meant. Nothing of any value was found; I filled the car up and headed for home, about 4 more hours at highway speeds. The warning lights stayed on and the VSC flashed the entire way home. The vehicle ran perfectly with no problems at all.

The next morning I started the car and the lights were out. Still worried, I purchased an OBD2 scanner and pulled a P0015 code, Camshaft Position - Timing Over-Retarded (Bank 1). I erased the code and the car has been fine ever since. Finally to the question, is this something I need to worry about? I travel this trip about once a month and don't want to get stranded along the road. The car has 54K on it and if it is a sensor in the engine, it should be covered by the powertrain warranty, but more importantly, will it cause damage to the engine? I read that the camshaft position sensor would only be replaced under warranty if it was inspected and causing a loud ticking noise, which I do not hear. If it throws the same error code again, I will take it in to the dealer and let them look into it.

View 5 Replies

Golf IV / Jetta IV :: 2005 - Code P0011 Intake (A) Camshaft Position Timing / Over Advanced (Bank 1)

2005 GTI 1.8t Engine ... I changed my timing belt water pump and tensioner yesterday and today I am receiving an engine code: P0011 Intake (A) Camshaft Position Timing - Over Advanced (Bank 1) My friend timed the engine and knew that is was 1 tooth advanced. He told me that is was going to be OK because 1.8t's have a 1 tooth tolerance. I would have redone it but I did not know how. What to do in this situation? Do I need to re time the engine?

View 2 Replies

Ford Super Duty (1999-2016) :: 2005 F250 - Timing Chain Rattle?

I have an 05 5.4 f250 that had a stuck injector. I changed plugs before I realized it was injector. After that the truck had a terrible rattling noise. I ended up changing timing tensioners and guides (guide was broken). Started it up and have the same noise, like timing chain is loose.

What I think happened is gas got into oil when injector was stuck. I had key on to pull codes. Then it lost oil pressure?

Could this cause can phases to go bad? Also can I just install lockouts or do I need to replace phasers as well?

Not sure if there's anything else I should check

View 2 Replies

Ford Super Duty (1999-2016) :: 22K With Hubs In Locked Position

Its a 2016 F-250, 6.2L gas truck with the electronic shift on the fly transfer case.

I have put right at 22,000 miles on it like this, frequently at 70-80 mph.

What are the odds I have damaged it and is there anything I should do now that I discovered it - other than put them both in "AUTO".

Truck has been to the dealer twice and not once was this noticed. They blamed the squealing on the brakes which I knew it wasn't.

View 14 Replies

Ford Super Duty (1999-2016) :: No Power In Accessory Position

When the key is switched to the accessory position, none of the things that are supposed to work in accy do. It's been like that ever since I bought the truck, but I never gave it much thought. Other than look for bad wiring, I really haven't tried anything. Where should I start?

View 6 Replies

Ford Super Duty (1999-2016) :: Steering Wheel Wobble In Any Position

My truck has developed a wobble in the steering wheel. I don't mean when you are driving down the road, but the steering wheel wobbles around. It wobbles in any position that the Till shaft is set to. How to repair.

View 10 Replies

Ford Super Duty (1999-2016) :: Gear Position Needle Not Working?

05 F250 FX4

Gear position needle (little orange line for an automatic) isn't working. It stays in the 1st gear position.

Tired of counting the "clicks" to know which gear I am in. How hard is this to fix?

View 1 Replies

Ford Super Duty (1999-2016) :: 2003 - Second Position Of Blower Switch Does Not Work

I have an '03 F250 and the second position of the blower switch doesn't work. The first, third, and fourth are all fine.

I bought a Motorcraft YH-1670 blower switch, but can't figure out where it's located?

I looked behind the glove box, but didn't see it there. I did not remove the screws to the cover behind the glove box because I wanted to first confirm where the switch is located.

View 12 Replies

Ford Super Duty (1999-2016) :: 2009 F250 - Wipers And Headlights Came On When In Off Position

2009 F250 lariat. While driving down the highway my wipers came on when stalk was in the off position. They would not shut off. Had to remove the relay to get them to shut off. Also, during middle of a sunny day the headlights would temporarily come on and shut off when it was in the automatic position. They would not come on if I put it in the off position though. Since both the wipers and high beams are part of the multifunction switch is it likely that the switch has gone bad vs. a more major issue with the computers. No other issues identified.

View 1 Replies

Ford Super Duty (1999-2016) :: Getting Exhaust Pipe Out?

The exhaust system from the downpipe back was stolen off this auction truck I bought, so I bought an even worse truck for parts but I'm struggling to get the exhaust off. Is there a trick to it? Does it come out going forward over the rear axle or pull out from the back? Should I just cut it and have a shop weld it back?

View 8 Replies

Ford Super Duty (1999-2016) :: 2008 V10 - Timing Chain Broken Or Fell Off On The Passenger Side Bank

Today I either broke timing chain or it fell off on the passenger side bank of my 08 F250 V10. Put a hole in valve cover. What to expect for repairs. Is this engine Zero tolerance.. unsure if I should expect bent valves or not and just how far I may have to go with this.. best way to test. I have a bore scope camera and mechanical abilities.

View 14 Replies

Ford Super Duty (1999-2016) :: Driver Side Window Quit Working In Up Position

I have a 1999 f250 crew cab. About 6 months ago my drivers side window quit working in the up position(lucky me) and last week I got around to fixing it . I just ordered a new window motor instead of the whole regulator and installed it and it worked perfect for 4 days and today it suddenly quit again. What would cause a window motor to go out again so quick? Everything else seems to be fine and there is power to it so I'm assuming it's the motor.

View 2 Replies

Ford Super Duty (1999-2016) :: 1993 F350 - Clutch Position Switch Fault?

I'm getting a random 'no start' fault which I think is related to a clutch position switch. The dealer tells me the clutch pivot bushing and master cylinder push rod are worn out, which is causing the switch not to close when the clutch pedal is depressed.

1993 F-350 7.3L Diesel 5 Spd 4x4, Std Cab, 8 Box.

View 1 Replies

Ford Super Duty (1999-2016) :: 2008 F250 - Wipers Came On With Switch In Off Position And Won't Stop

I have a 2008 f250 with 6.4. Was sitting my truck with key on and motor off listening to radio on lunch and my wipers came on by themselves. Switch was in off position and we're in slow speed. If I turn switch they wouldn't change speed til high position. Turned key off and back on and they came on still. Pulled 30 amp fuse in battery junction box to shut them off.

View 3 Replies

Ford Super Duty (1999-2016) :: Absolute Silence When First Turn The Ignition Key To Start Position

On my class C motor home, 1999 with V10 engine when I turn the ignition key to the start position I get absolute silence, when I release the key and turn it to the start position again it always starts. I have fitted a new starter motor, new solenoid and new battery but still the problem persists. I'm scared that one time it will not crank over on the second attempt.

View 10 Replies

Ford Super Duty (1999-2016) :: Key Won't Move To Off Position After Cylinder Lock Removal And Installation

I have a problem with an 2000 F250 7.3 6spd. Recently, the "key in the ignition" chime kept dinging even when no key was in the ignition. I read in the forums that a wire can be disconnected to stop the chime. The problem is that after I re-install the cylinder lock, I cannot move the key to the off position to remove the key. I can rotate it to start and run, but it won't move backwards to the off or acc position.

The truck has this little lever that normally needs to be pushed to allow key to be released, but even after pushing that, turning the steering wheel back and forth, and messing with the tilt, I still can't get the key into the off position. I have removed the cylinder and it looks good. It rotates properly and I can remove the key, but only when it isn't installed. I tried replacing the ignition switch, but the lock cylinder still doesn't move.

I have an 04 F250 that I've tried swapping the lock cylinders from the 04 to the 00, but it still doesn't turn. What might be the cause/fix? Also, the 2000 F250 has a intermittent chirping/squeaking sound under the dash that happens even when the batteries are disconnected - might this be a malfunctioning vacuum motor? It happens even though the truck hasn't been driven for a week.

View 1 Replies

Ford Super Duty (1999-2016) :: Stumble When Idling With A Pop Every Now And Then Out The Exhaust

I am new to Super Dutys but i love them! Altho mine is not being so nice. It has the 5.4 in it. When its idling it has a stumble to its idle with a pop every now and then out the exhaust. It revs fine when its first started. If i pull out on to the road and start away easy its ok a slight miss but if i put the throttle down its just falls on its face. But if i get it up to cruising speed its ok as well. But even at cruising speed more then 1/8 throttle and it starts missing and falling on its face. What it could be? It smells like its running lean as well.

View 14 Replies

Ford Super Duty (1999-2016) :: 2001 - Oil Leaking From Exhaust?

I own a 2001 F250, I bought a skid steer that weights 7000lbs and got a trailer that is 14,000lbs.

The truck was running fine, today was the first day I used it and I noticed by the end of the day I have oil dripping from my exhaust.

The dealership told me that the f250 is able to town that much weight, what caused it, as well as is it safe to continue to tow with it?

View 1 Replies