Ford Super Duty (1999-2016) :: Disable Day Time Running Lights Feature?
Just bought an 02 Super Duty 7.3 that has day time running light. Is there a way to disable this feature?
View 5 RepliesFord Super Duty (1999-2016) :: 2011 - Destination Feature Not Working
The destination feature on my 2011 has stopped working. I input all the information as to where I want to go and then press the icon to calculate the route and a window pops up saying that the calculation of the route failed. It does not say why it failed, just that it failed. I have tried several different destinations all with the same result.
View 7 RepliesLexus RC 2015+ :: RC350 Window Tint - Disable Auto Roll Down Feature
Have problems getting window tinted? Just got my RC 350 and i took it to one of the most referred places in town for tints. (small town)
Anyways, they are having trouble with the drivers side window bc that little autoroll down feature when you open the door keeps on messing up the bottom edge of the tint. I've already taken it back to the shop for them to fix it and now I have to take it back on Monday to get it fixed again.
Any way to disable this auto roll down feature on the rc 350?
Ford Super Duty (1999-2016) :: F250 - Safety Feature Lock / Unlock Only At Start Up And Cutoff
Just started a job with a company that has F250 super duty service vehicles and I am puzzled. All the answers I find don't seem to apply to this vehicle. With a full front seat and the big center console it kinda sucks to have to reach over or walk around to manual lock passenger door 10 times a day. I do NOT have power door lock buttons, number pad on handle, or any type of keyless remote. It seems I only have the safety feature lock/unlock at start up and cutoff. So is there anyway to make it not unlock passenger door when I turn ignition off? I even tried pulling fuse 17 that is marked as lock motors thinking that was related with no success. The dash display doesn't have the option to disable as listed in the manual as one of the 4 ways to turn it off. And for reference it does not behave the way the manual says about autolocking at 12mph. Its instant lock on key turn on and instant unlock both doors on key off.
View 9 RepliesFord Super Duty (1999-2016) :: Way To Disable TPMS?
Is there a way to disable the Tire Pressure Monitor System? I want to drop the pressure in my tires when it is not loaded but annoying sensor keeps going off.
View 14 RepliesFord Super Duty (1999-2016) :: Disable Cruise Control With IDs?
I have a newer 2012 f250 that i souls like to disable cruise control on, can this be done with auto ingenuity, our will the dealer have to do it with ids?
View 3 RepliesFord Super Duty (1999-2016) :: Way To Disable Reverse Sensor?
Any way to disable the reverse sensors by maybe adding a switch to turn off power so it does not constantly go off while plowing and the sensors are snow covered? i thought maybe by just unplugging the switch would do it, but that did not work. truck is an 02 diesel with auto trans.
View 6 RepliesFord Super Duty (1999-2016) :: 2012 F350 - How To Disable DRLs
How do I disable the day time running lights on 2012 f350?
View 4 RepliesFord Super Duty (1999-2016) :: 2015 - Disable ACC Door Chime?
How to disable my door chime with the key in and in the ACC position on a 2015 F350 Super Duty 6.7L. I did pull the blue wire with gray tracer to get rid of the key in chime. I want to use my truck for a radio when i am in the field.
View 4 RepliesFord Super Duty (1999-2016) :: How To Disable Passenger Side Window Switch
Any easy way to disable the passenger window control? Being a 2 door supercab, I do not have the "window lockout" button on the drivers control. I would like to be able to control the passenger window only from the drivers side. The problem is, my 2 dogs will put there paws on the passenger arm rest to look out the window. Occasionally, they step on the window down button. Once he stepped on the window up button, while window was down and would have gotten his neck stuck in the window had I not pushed the driver control to stop the movement of the window.
View 11 RepliesFord Super Duty (1999-2016) :: 2002 - Disable Automatic Door Lock Mechanism?
Can I disable the automatic door lock mechanism? Maybe pull a fuse? All of a sudden the locks start locking and unlocking over and over and the lights dim. I would like to disable the automatic and use the key to lock and unlock the doors. It is a 2002, F-250-Super Duty 4x4 SuperCab.
View 5 RepliesFord Super Duty (1999-2016) :: 2014 F250 - How To Disable Low Tire Warning Light
How to do this, or have had it done? I do have 35x12.50x18's on it. I did go to the tire center here in my town to have them reprogram it but only worked for a few to a week cant remember.
View 13 RepliesFord Super Duty (1999-2016) :: Auto Hub Not Working
Well replaced my u-joint on the passenger side along with the large knuckle seal. to say the least.. a nightmare. Got it all put back together and now my auto 4x4 is not working. dash says it's in 4x4 but it's not engaged. Worked fine before this little adventure. It's a 2006 250 superduty gas....
View 9 RepliesFord Super Duty (1999-2016) :: 2004 - 4x4 Auto (shift On Fly) Not Engaging?
2004 Ford F250 CC 4x4 6.0L
Took the family down to the beach today. Had some tough sand to get across in a few areas to move away from the crowds. Got a little dicey and the truck got stuck in 2WD. Switched to 4WD but back tires kept spinning. Couldn't figure out why and the truck started to dig deeper in the sand. Got a little nervous and I didn't want to start the day off with having to get pulled out.
Got out of the truck, locked the hubs in manually and I was out, no problem. Left the hubs locked until we left the beach and back on pavement.
What might be the problem and why the "shift on the fly" switch on the dash didn't seem to engage the 4WD? I even tried to switch into 4L and back to 4H (truck in neutral, break pedal compressed) and still no workie. Only manually locking the hubs would engage the 4WD.
Ford Super Duty (1999-2016) :: Front Hubs Not Auto Locking
My hubs will not lock when put into 4x4. I disconnected all lines from the solenoid to both hubs and tested them for leaks... All good there. I put a gauge on the lines at both hubs one at a time while the other is still connected and get no reading when switched into 4x4. I checked for vacuum right out of the solenoid, and I get 2inHg when switched into 4x.
The vacuum pump kicks on every time I start the truck, even if I just shut it off and re-start right away. There is no delay when switching my ac/heater controls to different settings or vent locations. So I know there is vacuum. How much vacuum I should be getting out of the solenoid to the hubs?
2004 F350 6.0L....
Ford Super Duty (1999-2016) :: 2007 - Auto Locking Hub Not Engaging?
I'm trying to figure out why my auto locking hubs do not engage. To isolate the problem shouldn't the hub engage if a vacuum is applied to that hub only? A solid 18 inHg is maintained at that hub for over 10 minutes but the selector will not rotate, which suggests to me the seals are OK. What then might be the problem?
View 13 RepliesFord Super Duty (1999-2016) :: F350 7.3 4x4 Auto - Flashing O/D Light
I have the dreaded flashing O/D light on my early 99 F350 7.3 4x4 auto. The only one's that seem to be consistently recommended are Snap-On or AutoEnginuity.
View 1 RepliesFord Super Duty (1999-2016) :: F250 4X4 - Auto To Manual Transmission?
I am changing my 99 f250 4x4 from auto to manual tranny. I am just looking for pics of where the hydro line runs. I don't want line rubbing something and ruining line. Like does line run under the cab wiring harness? Like between wiring and firewall? Where on firewall does reservior get mounted usually? Are the holes all ready there for it that I am not seeing?
View 1 RepliesFord Super Duty (1999-2016) :: Auto Locking Hub Retaining Ring Falls Out
I just replaced the ball joints on my 02 excursion and I can't get the locking hubs to seat far enough in so that the retaining ring keeps them in place. The ring seats but then works out as I'm driving. There is something keeping the hub from sliding in far enough so that the ring/clip can set deep enough in its groove. What's causing that? Its happening on both sides.
View 10 Replies