Ford Super Duty (1999-2016) :: P0088 Code - No Loss Of Power
So I'm not sure if I bought a lemon, but i picked up a F-350 6.4 Turbo Diesel two days ago and the check engine light came on yesterday. It's giving me a P0088 Code as well as the P0088pd. It's got 131,000 miles on it so no warranty will cover me.
I'm tracking the TSB put out telling the techs to replace the HPFP, but they mention a loss of power. I've only had the truck for two days, but I've driven them for work before and I can't detect any loss of power. Besides the code, everything seems to be running fine.
What can I can try out before running out and changing the HPFP? I'd rather not cut so deep into my savings if I don't have to.
Ford Super Duty (1999-2016) :: V10 - Scanner Won't Power Up And Read The Code
My 1999 super duty v10 has thrown a code but my scanner and a mechanics scanner won't power up and read the code, I also noticed that the cigarette lighter is dead. Which fuse controls both the plug and the lighter?
View 3 RepliesFord Super Duty (1999-2016) :: No Power On Small Hills - Code PO358
I have a 1999 Motor home has a 6.8L Triton V-10 just had a 100,000 milie tune up to include 10 new titanium spark plugs 3 months later I have this problem While driving the other day I had no power to take small hills. Little neighborhood hills were slowing me to 10 mph. Hoping its was the MAF sensor although it didn't throw a code when it was doing this but a code for PO358. So what's next back to the Ford Dealership for repairs?
View 5 RepliesFord Super Duty (1999-2016) :: Bad Valvetrain Noise On Power Steering / P0012 Code
I'm working on an 05 with a 5.4. I got it with a bad valvetrain noise on the PS, which ended up being a bad cam, and one bad rocker. I changed the bad rocker and any others that showed any wear, the cam, and all 12 lifters on that head.
The truck starts, idles, runs, and drives fine; identical to my own 05. But if I get on it, it has a dead spot around 3-4k rpm, then picks right up again. After a while, I get the p0012 (Variable camshaft timing over-retarded bank 1). After I get it pissed off, the idle gets rough as well and bogs down.
Now I know the cam went it correctly. I used the wedge tool so the phaser never left the timing chain. I marked the chain as well just to be safe, and the phaser only goes on the cam in one position. Also, it idles too nicely, and runs fine under normal acceleration.
Tonight I swapped the VCT solenoids from one side to the other. It took a lot longer to get the code, but finally came up as a freeze frame dtc, and on Bank 1 again, so it's not the solenoid.
So in my mind, all I can think is that the timing chain jumped (which I don't think is likely due to the good running under normal conditions), or the phaser is bad/sticking on Bank 1. I popped off the oil fill tube and the phaser looks fine physically, so I don't think I banged into it somewhere along the line. I also manually excited the Bank 1 solenoid by grounding the purple wire, and it gives my the same rough idle which I get after the p0012.
It looks like the phaser to me. Another mistake I made was not scanning the truck when I first got it. It came right from a repair shop which diagnosed the camshaft, but I would have at least known if they cleared any codes from it.
Ford Super Duty (1999-2016) :: Reduced Engine Power And Code P0088 Popped Up
I have a 2015 SRW f350 and has been fairly problem free. Last Thursday I was driving home and I received the reduced engine power and code popped up P0088, high pressure fuel rail issue.. anyway, I just popped over 36k miles, the truck is at 36,278 miles, so I take it in thinking they will goodwill it.
I get a call saying they can't clear the code and the TCM AND PCM can't communicate and they have to reach out to Ford engineering. They find the PCM is corrupt, they call me twice and ask if the truck has been tuned, the answer is no, but then pin me against the wall saying I am the second owner, which I am, and that it could have been tuned prior. I tell them to prove it, you can see if there has been a tune. The truck truly has never been tuned, it was sold at Ford factory auction as a employee vehicle.
Now they are trying to tell me the corruption was due to the tune, which it never had. But they won't goodwill it and say I am responsible for all the diag and work done, I say no. I say this should be a warranty issue and should be covered, they say it was tuned, I told them to prove it.
Ford Super Duty (1999-2016) :: 2010 F250 V10 - Lost All Power - Code P0300 Came Up
I have a 2010 F250 with the V10 and 42000 miles. Lost*power*while pulling a trailer. Couldn't get over 30 mph. Tried turning back home and lost all*power*and would barely idle. Fuel filter good air filter good. Code P0300 came up. Towed it back to the house and then couldn't even get it to idle. Wouldn't throttle up past about 2800 rpm. Cleaned MAF sensor and nothing. Somewhere during all that P0174 code came up and misfire cylinder 10. Cleared codes and they haven't come back. Now when trying to crank, it barely turns over, yet battery is good. Opened air filter cover after getting it to start one time and there was some light smoke coming out. Also while barely keeping it running for a little bit, the catalytic converter on the driver side was fire hot and the other side I could grab with my hand.
View 6 RepliesFord Super Duty (1999-2016) :: 2008 F250 - Throwing Code - No Power - Misfiring?
My 2008 f250 6.4l just got out of the shop a week a go new small block and new pistons, throwing #1 constrabution code,map sensor and #1 cil misfire you can hear air come out of the intake, I am guessing valve train or lifter..... other problem two days after the truck throwing the codes i went to take it to the shop and would barely drive floored struggle to go 10mph put it in park rev up normal will go in reverse normal just no power in drive, no transmission codes, had it towed to the diesel shop, mech said might be a fail safe on transmission from the engine codes? it has egr/dfp h&s mini maxx tuner, the truck has 170k on body 11k on new engine before the new block that was put in last week.
View 6 RepliesFord Super Duty (1999-2016) :: CEL Came On And Truck Ran Very Sluggish With Hardly Any Power - P040D EGRT Code
I have a 2009 6.4L F250 with 153k miles on it. Yesterday I drove from downtown Dallas north to McKinney (about 40 miles) and truck was running fine. Left approx. 3 hours later for dinner and the check engine light came on and truck ran very sluggish with hardly any power. Had it checked at auto zone today and got the P040D Exhaust Gas Recirculation temperature A circuit high DTC. I can get the part but not sure if I can replace it myself.
View 2 RepliesFord Super Duty (1999-2016) :: 2004 F350 - Shacking And Lost Power / Code PO284
I have a 04 f350 6.0L truck ran great all day today then out of the blue it started shacking and lost power then i plugged my tunner in and code popped up po284.
View 6 RepliesFord Super Duty (1999-2016) :: Losing Power In Reverse / Transmission Not Always Going Into Last Gear On Interstate - Code PO741
I have been having trouble with my 2008 Ford F250 4x4, 6.4 liter diesel transmission. SCT tuner, 10" lift, egg delete and dp delete has been done. I have been losing power mainly in reverse but have noticed that the transmission hasn't always been going into the last gear on the interstate. Code PO741 would come up. The other day the shifter was stuck. So I played with it and found that the cable on the transmission had fallen off. After replacing it. The transmission wouldn't go into reverse but has been doing semi good in forward. Well I have been limping it around until today when I was going down the road and it completely stopped pulling. Now no matter what gear I place it in, it will on go in reverse. What could be causing these issues or where to even begin to start looking?
View 3 RepliesFord Super Duty (1999-2016) :: 2006 F250 Running Rough / No Power On Acceleration / Code PO420?
CEL came on last night, OBD code PO420, truck is an 06 f250,5.4? Btw, truck running rough, no power on acceleration, in gear at idle, runs rough....
View 4 RepliesFord Super Duty (1999-2016) :: F350 - Black Smoke And Low Power / Code P1211 Under Heavy Throttle
I have a 99 350 sd 7.3 low power black smoke sets a p1211 under heavy throttle. Check icp on scanner under heavy throttle falls from 1900s to mid 1700s ipr duty cycle runs about 62% wanting to know if I am looking for a hpop problem or injector issue...
View 1 RepliesFord Super Duty (1999-2016) :: Brake Code 4
What a Brake Code - 4 means for a 1999 Super Duty on the door ID tag?
View 4 RepliesFord Super Duty (1999-2016) :: 2007 - Key Code Resets
I just purchased a f350 super duty 07 4 dr long bed with the 6.0 liter trying to find the 5 digit code so i can reset key pad on door.
View 2 RepliesFord Super Duty (1999-2016) :: New X Code Springs And Now Squeaking
Replaced my old sagging leaf springs with new X code springs. Had an almost impossible time centering the axle even with adjustable center link. Even with it totally maxed out it is just barely centered. Now I have a terrible squeak coming from springs. Is this because of the side loading of springs? Is there any fix for it? Not only do they squeak but the drivers side now sags almost an inch even with brand new springs. 2002 F350. Super annoying and irritating
View 1 RepliesFord Super Duty (1999-2016) :: Code P2285 - New ICP Sensor
I have been trying to find a new sensor after my truck popped a P2285 code. I can't find ICP sensor at any auto parts store. I found this but it was labeled as a fuel pressure sensor on RockAuto: More Information for Standard Motor Products ICP103... Is this the same thing?
View 2 RepliesFord Super Duty (1999-2016) :: Code Showing For Knock Sensor?
Code was showing for the knock and climbed under the truck and checked to see if it was plugged in grabbed the wire and to my surprise the wire kept coming and so did a piece of the knock sensor, is this going to affect my truck badly?? worst case?? 97 f250 4.6 standard
View 4 RepliesFord Super Duty (1999-2016) :: 2000 - Blank Axle Code?
I plan to be buying a 2000 F250 V10 in a couple of hours.
I had my boss run by and take a picture of the door tag so I could determine the axle code. What he sent me was this:
Other than giving me the knowledge of how bad of a photographer he is, it doesn't tell me much else. The axle code area is blank, what gives? Am I just going to have to crawl under the truck when I get there after work?
Ford Super Duty (1999-2016) :: Misfire At Low RPMs - Code P0316
2004 SD ext cab 5.4L Gas ! I have a mis-fire at low RPMs ! Autozone said it kicked out code P0316 Crank Position Sensor ( CPS ) but the CEL was not on ! So I replaced it and Still has the same problem. I checked the coil packs there good according to the autozone diagram "how to" ! I also pulled each wire 2 check the old shade tree way to see if I could tell that way. Now the CEL is on...
View 14 Replies