Ford Super Duty (1999-2016) :: 2008 F250 - Little Bit Of Movement In Front Wheel Bearing And Hub Assemblies
I have a 2008 F250 5.4 4x4 supercab long box (68,000 miles) that has a little bit of movement in the front wheel bearing and hub assemblies. Made it through inspection OK but it will need to be changed soon. Just asking for everyone's thoughts on brands they prefer. I have had great luck with Moog brand products in the past. I put SKF hubs on my wife's 2010 Explorer and they I would say are top quality also. Not interested in a conversion kit or cheap junk. I want a good quality unit. What brand has everyone had good results with? Are Moog or SKF the way to go?
View 8 RepliesFord Super Duty (1999-2016) :: 2003 F250 - Knuckle / Axle Seal Replacement
Replacing the knuckle/axle seal due to my hub not holding a vacuum. I finally got the seal off the axle after several minutes of beating, but it finally came off. During the beating the metal shield that was in back of the seal took a beating as well and can not be reused. Is it really needed?
In this thread the pictures show that the shield was not installed after the seal was replaced. The shield does serve a purpose to keep crap out of the seal though.
Ford Super Duty (1999-2016) :: 2001 F250 - ESOF Vacuum Knuckle Connector
I am in the process of rebuilding my front end and have found that the nipples that screw into the top of the knuckles for the ESOF system are rusted and need replacing. I'd like to keep the system as close to original as possible, but have had no luck in finding a replacement. What the appropriate Ford part number is or where I could pick up a suitable replacement. This would be for a 2001 F-250 4X4 with the V10.
View 2 RepliesFord Super Duty (1999-2016) :: Play In Steering Wheel / Loose Front End Suspension Parts
I have a '99 F250 w/ PSD with 165k miles.
When I drive, I move the steering wheel and nothing happens for the first few degrees of turn and then I encounter resistence and it turns. It's the same either way. The vehicle seems to track nicely, doesn't pull to either side, just a lot of slop in the steering wheel.
Is there a way to determine if this is really steering related or is it just loose/worn front end suspension parts making themselves known? My guess is suspension items, but the fact the front end behaves itself when the truck is moving has me doubting that just a bit.
Ford Super Duty (1999-2016) :: 2004 F250 Stumbles / Struggling Hard Almost A Side To Side Movement
I have 2004 Ford, thought it needed injectors because it was struggling hard almost a side to side movement. Had a friend recommend replacing the FICM, did that now it stumbles, less often, less movement like it's muted. I noticed it again yesterday after hard breaking, but also really likes to do it in heavy traffic.
View 1 RepliesFord Super Duty (1999-2016) :: Steering Wheel Knuckle Wear / Tie Rod End Rocking Back And Forth
I have a 2000 Ford F-250 that I have just replaced the tie rod ends on both wheels. The hole where the tie rod attaches to the right steering knuckle getting wallowed out? When I turn the wheel I can see the tie rod end rocking back and forth.
Now if I keep tightening it down it would pull it down past the cotter pin hole exposing way more threads than any to the other tie rod ends. I've searched everywhere and can't find anything that refers to this problem.
Ford Super Duty (1999-2016) :: Tight Steering Knuckle With Ball Joint Replacement
My 2004 f250 ball and u joint replacement job is at a bit of a stand still. Tore it down, brought the knuckle and axle shafts to an ex mechanic I know, because he has a 20 ton Harbor freight shop press. He mostly used a hammer, bashed out the old ball joints (I already had removed the u joints). U joint turned out fine.
I did notice the upper ball joint protruded a very slight bit on one side in the knuckle, meaning you could feel with your finger on the underside of the joint and on the one side it is not exactly flush with the interior of the knuckle. I would say it protrudes no more than a thirty second or so.
I brought it home, installed the boots on the moog joints, (the bottom was unusually difficult to put on), greased the joints and hung the knuckle on the axle tube, by a few turns on the lower joints nut. I then inserted the camber sleeve on the top stud, torqued the bottom to 49 fp then the top to 67 and finally the bottom to 150. End result, very stiff movement on the knuckle. No tie rod attached, and it takes to hands to move it from the "stopped" position,(turned all the way). I am sure it is stiffer than when I did the other side.
I tried loosening the nuts completely, same stiffness. I redid the torque sequence, no change. Tried hammering the ears around where the joints seat no improvement. The fellow who installed into the knuckle came and took a look. He agreed the knuckle was stiffer than you would hope, but, he suggested Putting it all together, as he believed they would loosen up before too long. I am not sure whether to try that, or remove the knuckle now, and redo with new joints. Pros and cons to either approach.
My question is : Does a knuckle become more sketchy by the time it is dealing with the pressing of a third set of ball joints? If I finish the install now, will a stiff knuckle action lead to other mechanical wear within a thousand miles or so, while I wait to see if they loosen up?
Ford Super Duty (1999-2016) :: Ball Joint Replaced / Driver Side A Bit Stiff To Turn The Knuckle
I just replaced the ball joints on my 99 F250 SD 4x4. Driver side was a bit stiff to turn the knuckle. Passenger side is very hard to turn. The upper stud wanted to turn in the sleeve after torquing to spec. I had to lean on it to lock it into place. I have to check today to see if parts store is open to get a new set. The brand name is "Drive Works". I have installed ball joints in this vehicle previously, and in another Ford truck with the same style. I have the proper tools to do the job. I have to determine if both joints are tight or just the upper. I won't buy the same brand again.
View 4 RepliesFord Super Duty (1999-2016) :: Very Little Air Movement Through Vents
With my A/C turned up on max A/C and fan speed set on highest setting, I get very little air movement through the air vents. I have been told that starting with 2000 year models, there is a filter on the A/C fan motor. If this is true, I am sure mine needs to be changed. Looking for procedure/schematics for removal and change.
View 14 RepliesFord Super Duty (1999-2016) :: Suspension Stabilizer Bar - Up And Down Play
Checking the front end with the front wheels off the ground I noticed that my Suspension Stabilzer Bar has about an 1/8" up and down play in it. No side to side play at all. I checked the nut on the ball joint and it is tight but wondering if this is why I am feeling a slight tight/loose feeling when going down the freeway at 65.
It has this "tight" or a slight grab feeling when the steering wheel is centered and I move it left or right slightly (like normal steering wheel movement to stay in your lane) I don't feel this at slower speeds 30-40 etc just when I am straight on the freeway at about 65-70 mph.
Ball joints and everything else looked fine, no play noticed. Never had the "death wobble" but having this up/down play in their stabilizer bar.
Ford Super Duty (1999-2016) :: Excessive Movement In Steering Wheel While Driving
I have a 2005 F250 6.0.. I'm the third owner, only 146,000 miles on it. Had most of the front end replaced. Ball joints, tie rod ends, track bar bushing, front end alignment done...
Still likes to walk as I call it side to side while driving down the road. Factory size tires, factory rims. A little excessive movement in steering wheel while driving, side to side and not transferring to pitmen arm. So I think the gear box shot. Got to looking closer and the power steering box has a re-manufactured sticker on it, so thought about rebuilding it. I do not know where previous owner got gear box at.
Ford Super Duty (1999-2016) :: 2009 F250 - AC Turned On But No Fan / Air
I just bought an 09 f-250 lariat 6.4 . It has 100k on it. Was driving it AC was working fine. Next time I got in it went to turn the AC Auto on and nothing..the display works fine..lights work..looks like it is working, but nothing. No fan no anything.
Also, the check engine light will come on too. Then next day everything works fine again. Check engine light is out..everything looks perfect. Then this morning the same thing happened..check engine light and no AC.
Ford Super Duty (1999-2016) :: No Movement From Steering Wheel / Pulsating Bounce In Rear End
I've been chasing this for longer then i can remember. At 40-45mph the rear end feels like its bouncing. no movement from the steering wheel, just a pulsating bounce. Little information about the truck: Has had Napa Gold shocks, Bilstein 5100s and currently Monroe reflex shocks. Installed readylift 4inch rear block kit about 2 years ago. Had 16x9 rims, currently has factory 16x6.5. Tires are 285/75s. New pads rotors and calipers. It's just driving me nuts to have it bounce all the time.
View 9 RepliesFord Super Duty (1999-2016) :: 2015 - Radio Only Play For 3 Seconds Then Off?
have a new 2015 SuperDuty that when you start engine, then turn radio on,,,radio will play for 3 seconds , go off for one or two,comes back on repeats process for four or five minutes before the radio or CD player plays on on continuous basis,,,is this the way the new radios operate?
View 3 RepliesFord Super Duty (1999-2016) :: 2009 F250 5.4L - 2 Misfiring Cylinders
I have a 2009 f250 with 5.4l 3v. have had the truck only about 6 months. it started missing about a month after I got it. I replaced all 8 cops and all 8 sp. The truck ran excellent until 11/29, then I got a cel and the truck started running really bad. Found 3 misfiring cylinders. Changed all 3 cops again and that did nothing. Pulled the injectors and found 2 of them were clogged, replaced those also. Still no change was told by someone that the ecm/cpu may need to be reset, did that also. Still no change. There are no codes present but still has the multiple misfires.
View 9 RepliesFord Super Duty (1999-2016) :: 2009 F250 V8 Stuck In Park?
My father has a 2009 Ford F-250 Superduty with the 5.4l V8. Two days ago, he frantically woke me up from a nap because he could not get the truck out of park nor are the brake lights turning on when the pedal is pressed. I instantly thought Shift Interlock, did a quick google search and found that it can be the shift interlock or brake light switch on the brake pedal. I have since then replaced both to no avail as well as checking all fuses. I put a multimeter to the brake light switch connector and am getting a steady 10.2v. I am aware there is a bypass switch but that doesn't address the fact that he has no brake lights.
View 9 RepliesFord Super Duty (1999-2016) :: 2009 F250 - Wind Noise Only Happens When Going At Least 70 MPH
I just bought a 2009 F250, I am getting a wind noise that I can't figure out where it is coming from. It only happens when I'm going at least 70 and into the wind. It is a short flute sounding noise that is intermittent.
View 6 RepliesFord Super Duty (1999-2016) :: Door Hinge On Driver Side Getting Some Play
After the years and 300k miles, the door hinge on the driver side door are getting some play. I wonder if i can replace just the pin on this hinge or the whole thing needs to be replaced. By the way, I am talking about a 00' F450 ...
View 2 RepliesFord Super Duty (1999-2016) :: 2009 F250 - Removing Throttle Body?
Read about and want to clean my throttle body. Why have to remove it from the truck ? 2009 f-250 5.4 .....
View 5 Replies