Ford Super Duty (1999-2016) :: Tight Steering Knuckle With Ball Joint Replacement
My 2004 f250 ball and u joint replacement job is at a bit of a stand still. Tore it down, brought the knuckle and axle shafts to an ex mechanic I know, because he has a 20 ton Harbor freight shop press. He mostly used a hammer, bashed out the old ball joints (I already had removed the u joints). U joint turned out fine.
I did notice the upper ball joint protruded a very slight bit on one side in the knuckle, meaning you could feel with your finger on the underside of the joint and on the one side it is not exactly flush with the interior of the knuckle. I would say it protrudes no more than a thirty second or so.
I brought it home, installed the boots on the moog joints, (the bottom was unusually difficult to put on), greased the joints and hung the knuckle on the axle tube, by a few turns on the lower joints nut. I then inserted the camber sleeve on the top stud, torqued the bottom to 49 fp then the top to 67 and finally the bottom to 150. End result, very stiff movement on the knuckle. No tie rod attached, and it takes to hands to move it from the "stopped" position,(turned all the way). I am sure it is stiffer than when I did the other side.
I tried loosening the nuts completely, same stiffness. I redid the torque sequence, no change. Tried hammering the ears around where the joints seat no improvement. The fellow who installed into the knuckle came and took a look. He agreed the knuckle was stiffer than you would hope, but, he suggested Putting it all together, as he believed they would loosen up before too long. I am not sure whether to try that, or remove the knuckle now, and redo with new joints. Pros and cons to either approach.
My question is : Does a knuckle become more sketchy by the time it is dealing with the pressing of a third set of ball joints? If I finish the install now, will a stiff knuckle action lead to other mechanical wear within a thousand miles or so, while I wait to see if they loosen up?
Ford Super Duty (1999-2016) :: Doing Both Lower Ball Joint?
I need to do both lower ball joints. is there a write up or process to do it? do I have to remove the whole hub assembly/knuckle thing or can I do it with all that stuff in place?
View 4 RepliesFord Super Duty (1999-2016) :: F250 - Ball Joint Replacement?
OK, I've done a lot of things over the years on cars and trucks but never messed with ball joints on a F250SD 4x4 with 160k miles. Found out today when getting new tires that the ball joints are shot. I trust the shop but know I can do this my self. So if I'm going to do this what should I replace? Since I'll be doing this I want to know from those with more time under the truck than me what else should I be replacing at the same time. I have done the front wheel bearings and of course shocks. Just what am I in for and what other parts and brands should I be using? Bushing kits for stabilizer bar? Replace stabilizer bar with heavier after market?
View 12 RepliesFord Super Duty (1999-2016) :: How To Stop Ball Joint Squealing
I can't afford to replace it now and want to quiet the squealing that occurs only when I turn right. A mechanic sprayed something on there about a month ago that caused the squealing to stop for about a week, but don't remember what it was. It's a 2002 S.D....
View 14 RepliesFord Super Duty (1999-2016) :: How To Tighten The Nut On Lower Ball Joint
I have replaced my ball joints and now putting everything back together. I am having trouble tightening the nut on the lower ball joint, the joint turns with the nut as soon as it starts to get tight.
View 2 RepliesFord Super Duty (1999-2016) :: Steering Is Pretty Tight / Ball Joint Break In Period?
Took my truck in to get the wheel bearings replaced (driver's side was singing pretty loud). Decided to have the ball joints replaced at the same time since they were still original at 133,000. Got the truck back and the steering is just not right. At high speeds it acts like an old F100 wandering back and forth and the steering is pretty tight when you try to correct the wandering. I have taken it back to Ford and had the alignment checked twice.
They adjusted it slightly and "loosened" the stearing gear box. Truck is better at low speeds but still not right at highway speeds. Ford is telling me there is a "break-in" period for the ball-joints. I don't remember my friends F350 having a break-in period when he replaced his ball joints. Truck tracked fine before the work was done. Tie-rod ends also checked out. Truck is a 99 350 CC SRW 8ft bed.
Ford Super Duty (1999-2016) :: 2001 F250 - Frozen U-Joint In Driver Side Front Axle
I have a '01 F250 with a frozen u-joint in the driver side front axle. My question is can I put it together without the axle and drive it?
View 2 RepliesSanta Fe (CM - 2007-12) :: Ball Joint On LCA Does Not Want To Go Back In Knuckle
I have a 2007 Santa Fe GLS. I took both LCA's out and replaced the bushings and the ball joints with Hyundai original parts.
I installed the bushing ends of the LCA, put the bolts thru both bushings, and then tried to insert the ball joint into the knuckle. No go! It goes in about a 1/4 inch.
How do you get the ball joint end to go all the way up, inside the knuckle? I am thinking of pounding the heck out of it till it goes in, but not sure.
I've disconnected the outer tie rods, and the links to allow for some play in the knuckle, I just don't know what I am doing wrong.
Ford Super Duty (1999-2016) :: 2003 - Replaced Front Hub Now Driver Side Leak - Replace All?
I replaced my my front hub assemblies on my 2003 F250, 4x4, about two years ago and my driver side hub is leaking. I first noticed it the other day when I tried to shift into 4 wheel drive and my hubs would not lock in the ESOF system.
I used a vacuum pump and it leaked down pretty fast so I assume the knuckle/axle seal is the culprit.
I plan on ordering these three seals:
Amazon.com: f81z-1s175-hca
I am also noticing another # for the axle seal. It is 3C3Z-3254-CA. Which is correct for my 2003?
Are my questions would I actually need to replace all three? The dust seal is not leaking at the moment. Should I go ahead and replace it anyway?
What type of grease do I need to use the seals? I have some disc brake bearing lithium grease in the cabinet. Will this work or do I need to get a specific type
Lastly, I've seen a post where members have made their seal seating tool out of the galvanized pipe, cap, and a flange. The flange is said to be too large and it would have to be ground down for the right diameter.
Ford Super Duty (1999-2016) :: After Ball Joints Installed And Alignment Steering Won't Turn?
99 F250 super duty 7.3
Had new ball joints installed and alignment. Steering does not return to center. Returns a little on a tight turn like in town but difficult when just changing lanes in town or not. Took it to another shop and they said the ball joints were too tight. right side pretty tight and left side really tight. Moog ball joints. First mechanic says they will get better with a few miles on them. Second mechanic says not so.
Also, have new shocks but get a bouncing in the front when at 45 mph and goes away at almost 50 mph.
Ford Super Duty (1999-2016) :: Steering Stiff / Extremely Hard To Turn At Low Speed Just Off Idle
My steering got real "heavy" almost as if I had no power steering so I replaced the power steering pump. The steering got a little easier but is still very stiff. It's extremely hard to turn at low speed just off idle...I have to rev the engine a bit to get it to turn.This is on my 1999 7.3 f350...I've ran 33" and 35" tires on it it's whole life and this is the first PS pump I've replaced since 1999...never replaced the steering box.
View 9 RepliesFord Super Duty (1999-2016) :: Changing Bulb On Driver Side Front Turn Signal?
Is there a way to change the bulb without removing the grill and headlight? Seems like a lot of work to replace a bulb. 2013 F350....
View 3 RepliesFord Super Duty (1999-2016) :: Power Steering Stiff And Almost Impossible To Turn Wheels At A Dead Stop
I have a 2001 F250 SD V10 and when at a dead stop and with the brakes applied, steering becomes very stiff and almost impossible to turn the wheels. If I let off of the brakes and move a little the steering is just fine. I hate like hell to spend the money on a new power steering pump if it isn't going to fix the problem. Simply put, deap stop, brakes on, wheels don't want to steer. How do I fix it?
View 10 RepliesFord Super Duty (1999-2016) :: 2002 F250 - Radio Is Staying On When Turn The Key Off And Open Driver Side Door
I have a 2002 f250 7.3, an my radio is staying on when I turn the key off and open the drivers door. Windows are also still working. But if I open the passenger door it shuts off. What do I need to fix this I am tired of leaning way over and tryind to open that door every time I turn the truck off. I have been told to spray wd-40 into the door catch are i used a whole can an it still isn't working...
View 2 RepliesFord Super Duty (1999-2016) :: Steering Wheel Knuckle Wear / Tie Rod End Rocking Back And Forth
I have a 2000 Ford F-250 that I have just replaced the tie rod ends on both wheels. The hole where the tie rod attaches to the right steering knuckle getting wallowed out? When I turn the wheel I can see the tie rod end rocking back and forth.
Now if I keep tightening it down it would pull it down past the cotter pin hole exposing way more threads than any to the other tie rod ends. I've searched everywhere and can't find anything that refers to this problem.
Ford Super Duty (1999-2016) :: 2003 F250 - Knuckle / Axle Seal Replacement
Replacing the knuckle/axle seal due to my hub not holding a vacuum. I finally got the seal off the axle after several minutes of beating, but it finally came off. During the beating the metal shield that was in back of the seal took a beating as well and can not be reused. Is it really needed?
In this thread the pictures show that the shield was not installed after the seal was replaced. The shield does serve a purpose to keep crap out of the seal though.
Ford Super Duty (1999-2016) :: 2001 F250 - ESOF Vacuum Knuckle Connector
I am in the process of rebuilding my front end and have found that the nipples that screw into the top of the knuckles for the ESOF system are rusted and need replacing. I'd like to keep the system as close to original as possible, but have had no luck in finding a replacement. What the appropriate Ford part number is or where I could pick up a suitable replacement. This would be for a 2001 F-250 4X4 with the V10.
View 2 RepliesFord Super Duty (1999-2016) :: 2009 F250 - Front Knuckle / Hub Play Movement
Should there be any play on the backside offront hubs (knuckle)? When I grab the knuckle where the sticker is theres alittle bit of wiggle/play especially on left side, little less on right. The truck is 2009 and has only 11,000 miles on it.
View 4 RepliesFord Super Duty (1999-2016) :: 2005 F250 Won't Turn Over After STC Fitting Replaced
2005 6.0 F250 SD Powerstroke... Truck died on the road and wouldn't start
The symptoms were... I changed the Radiator and had the cooling system flushed... couple of weeks later it stopped while driving... did some research and talked to a few people and the STC valve seemed to be the issue... So new STC, new intake gaskets, cleaned and new EGR gaskets and I just put in a new Turbo (Ford installed it)... had a stripped bolt under the EGR cooler arm and had to remove the Turbo to get to it.... 14 days later......
Changed STC fitting and gaskets in the high pressure oil pump, IPR screen, exhaust manifold gaskets and Cleaned the EGR and changed gaskets and no start. Tried starter fluid and it turned but wouldn't stay on and the batteries died. Would you all say I'm on the right path?