Ford Super Duty (1999-2016) :: 2005 F250 - PCV Valve Location
I have a 2005 f250 with a 5.4l 3v. Where the pcv valve is located is it in the valve cover or attached to the intake and what does it look like? I have pulled the hoses off both sides but I have not found it let.
View 3 RepliesFord Super Duty (1999-2016) :: 2005 F450 - Air Cooler Removal To Clean?
Buddy is fixing his 6.0 2005 F450 with a blown turbo. Diagnosed by the dealer, but decided we could fix it ourselves. The dealer quoted a turbo and to pull the charge air cooler and clean. It looks like the turbo job is not too bad to do, but how big of a job is the R&R of the charge air cooler?
View 9 RepliesFord Super Duty (1999-2016) :: 2005 F350 - Parking Brake Cable Removal
I'm working on an '05 F350 King Ranch dually, and I'm pretty sure the pb cable is stretched. I recently replaced the shoes in the pb assembly and adjusted the tension while I was in there, but it still barely holds. My next culprit sounds like a stretched cable, and I have a complete set for a new one, but I'm having a hell of a time getting the old one out. The link that holds the front and intermediate cables together won't pry open with any tool I have, and I've broken two drill bits trying to drill out the nub holding the front cable in.
View 5 RepliesFord Super Duty (1999-2016) :: 2014 - Removal Of Bed Stickers?
I want to remove the 4x4 stickers on my 2014 SD box. I think it looks cleaner without them. Are they difficult to remove or does the hair dryer trick and then some Goo-Gone do the trick without a big time effort? The last thing I want to do is make a mess of the paint finish.
View 13 RepliesFord Super Duty (1999-2016) :: Tailgate Handle Removal?
Looking to get rid of the step handle, I did this mod on mine and it was a direct fit...take off old liner and unbolt handle, then get a liner from a non-step tailgate and it is a direct fit:
View 7 RepliesFord Super Duty (1999-2016) :: Transmission Line Removal?
OK, so I ordered in the new lines and have them. BUT my problem is snaking the factory transmission line out from under the truck. I have pictures to show my struggles.
How do I pull this:
Out of here???
Towards the front of the motor
Front passenger side cab corner
Replacing these lines? I don't care about breaking the old one, but I still need to find a way to install the new one.
Ford Super Duty (1999-2016) :: Center Console Lid Removal
I am wanting to take off the center console lid to recover it. The only way I see to remove just the lid from the truck is to hit the rod out that is in the hinge. I was hitting pretty hard with a punch and it wasn't moving. I don't really want to break it so I'm asking if there is a different way or if I just need to use more force?!
View 4 RepliesFord Super Duty (1999-2016) :: HPOP Reservoir Oil Removal
Is it necessary to remove say about one and one half cups of oil from the HPOP reservoir when changing oil? I say not needed.
View 3 RepliesFord Super Duty (1999-2016) :: Transmission Line Removal?
I have replaced both the transmission lines except the one that connects the two. It is the one near the top of the transmission that is about a foot long and goes from the fitting of the one transmission line to the other fitting for the other line. My questions is how do I remove it? It seems to be permanently affixed to the fittings, so those it come attached to new fittings?
View 2 RepliesFord Super Duty (1999-2016) :: F250 - Headlight Removal?
I dont want to pry on the wrong thing and brake something. I am trying to remove the headlight. I was told that their are some pins that need to be pulled up. I dont see any pins. I do see two plastic clips on each side of the headlight. They are flat on the top with a small slot in them. There is a "T" stamped on the top of it. Are these the pins? I tried to find a shop manual today without much luck. Looking for a picture to show the pins that need to be removed.
View 7 RepliesFord Super Duty (1999-2016) :: 2008 - EGR Valve Sticks?
Quick question, 2008 F250, 6.4. If the EGR Valve sticks/malfunctions, can this cause the truck to go into constant/frequent regens? I am asking because I am about to replace my turbo for a seal failure. The only code thrown before turbo failure was EGR flow insufficient. I want to figure out what may have caused the seal failure so that I can get that fixed before I blow through another turbo.
View 10 RepliesFord Super Duty (1999-2016) :: Front Rotor Removal For Replacement
I can't figure out how to get my front brake rotors off to replace them. I removed the caliper and thought the rotors should just come right off but they didn't? I then pulled the hub out and there was a retaining ring with a good size nut behind it , but you shouldn't have to remove the hubs to remove the brake rotors should you?
The stats of the truck are 04 f250 4wd w/manual hubs!
Ford Super Duty (1999-2016) :: 2004 - Removal Of Bench Seat?
Just bought my first 04 F250 super duty Xl...4x4 Ext Cab...need to get this bench seat out and buckets and console in!!! I hear this is easy swap but never done before, or believe anything is easy.
View 1 RepliesFord Super Duty (1999-2016) :: 2012 - Overhead Console Removal?
How to remove the overhead console on a 2012 F-250 ? I would like to tap into the wiring to power my radar detector.
View 7 RepliesFord Super Duty (1999-2016) :: Rear Fender Flares Removal?
I want to get the rear fender flares on my dually painted, they had a few scuffs when I bought it & I will soon have some spare time to get it sorted. We can't get the truck in the paint booth so taking them off seems like the ideal solution. I have had a quick look & I think it's just a case of removing the plastic liner (screws & clips) then it looks like there are some nuts up inside the steel fender, disconnect the wiring & they should come off!
View 2 RepliesFord Super Duty (1999-2016) :: JB Weld For Manifold Stud Removal
I started to do my manifold and am 2 and 2. I got 2 out and two broke on top. So far I haven't been able to do anything w the bottom. I have basically seen 2 ways to get the studs out when they break. The first I'd to drill w an ez out and the 2nd is to weld a nut on. I'm not great w a drill and can't weld. I was wondering if using JB weld might be an option. I have never used the stuff but supposedly it's pretty strong. Is there any risk of welding the nut to the head?
View 12 RepliesFord Super Duty (1999-2016) :: 2004 - Stock Manual Hub Removal?
I'm replacing the passenger side manual hub on my '04 F250. I did a brake job last year and I'm sure I cleaned/inspected/lubed the hubs. I can't seem to get this one out. I have the snap ring out and with a rubber mallet, I can get it wiggle just a little. I've loaded up around where the snap ring went with penetrating oil.
Am I missing something? It's just a snap ring and the hub should just pull out, right?
Ford Super Duty (1999-2016) :: Removal Of Trailer Brake Controller?
Have recently been getting a "TBC Fault" message and the Beep, as the message goes on and off(annoying) looked around think its the Controler itself,,If I move the slider, and Jiggle it,,the message Blinks on and off as I move the Slider,,,Looking for the method of removing it from the Cubby Hole,,,Gave it a tug,,,and wiggle did not move must have a Clip or Tab to release it.
View 8 RepliesFord Super Duty (1999-2016) :: 2008 F250 - Hub Assembly Removal
I am trying to replace the ball joint on my 2008 f-250. Does the hub assembly come off of the knuckle or do you remove the whole knuckle and hub assembly together? If you have to remove the hub assembly what is the best way?
View 14 Replies