Ford Super Duty (1999-2016) :: 2011 F350 - Transmission Shifting Hard From 3 To 4 Going Up And 2 To 1 Going Down
I have a 2011 F-350 6.2L that has extremely hard shifts from 3 to 4 going up and 2 to 1 going down. Sometimes on downshifts it feels like something has ran into the back of the truck. I had the computer updated when the truck had approximately 40,000 miles on it and he assisted a little bit. The truck now has 140,000 miles and it is back to shifting horribly. I put it in the shop at the dealer on 30 December 2013. The dealer says that the problem is that the shift solenoids need to be replaced but that they are not available. The truck is still sitting at the dealer and I am being told that the parts should be available mid February.
View 10 RepliesFord Super Duty (1999-2016) :: 2002 F350 - Shifting Really Sluggish Between 1st And 2nd Gears Only
2002 f350 7.3 ... problems started all of a sudden one day. I have an edge evolution tuner in my stroke. I have it set to make all of my shifts firm. One day it started shifting really sluggish between 1st and 2nd gears only. It don't do it all the time, but it does it more often then it doesn't. I have also noticed when i come to a complete stop and then start out again it seems that it doesn't downshift all the way back to first and when i hit the gas it seems to kinda be stuck between gears and it barely moves until i get the rpms up before it will ease its way into 2nd and the converter locks up.
It shifts a through all the other gears just fine nice and firm like it should, its just the shift between 1st and 2nd. Im wondering if maybe it might be the speed sensors or maybe the tranny filter is getting clogged up? The fluid in it is still nice and red and up to the level it should be. I just bought the truck in october and the fluid was nice and red when i bought it, but who knows if they changed the filter. I have had NO tranny problems with it up until a few days ago when this little problem started.
Ford Super Duty (1999-2016) :: 1995 F250 - Shifting Really Hard And Searching For Gears
So I have a 1995 f-250 4x4 with the 460 and a E4od. So when I bought the truck I drive it two hours home and when I got into town it started shifting really hard and searching for gears. So I flushed it and installed a new oil filter because the oil in it was brown. Very brown. And smelled awful. So it shifts good, but what's happening now is that it shifts good in drive when it wants to.
In the morning it works great but when I get in it to leave after school it shifts really late (around 2900 rpm) and hard. So I put it in first and then into second but when it's time for third and I put it in drive it shifts back to first. But if I stop shut it off for a few minutes and turn it back on it works fine. It only does this after it's been sitting in the school parking lot all day. I replaced the mlps but not the connector due to I didn't have time at the moment. Could it be the tps? Something mechanical?
Ford Super Duty (1999-2016) :: Transmission Shifting Hard Between 2 And 3 Gear
The tranny is shifting really hard between 2 and 3 if I feather the throttle it can be a little less of a jolt but still enough none the less iv never done a filter and fluid change as I just got it it has 235000 miles 99 v10 super duty 4x4....
View 8 RepliesFord Super Duty (1999-2016) :: 4r100 Transmission Shifting Hard
Recently I have had an issue with my auto which was just rebuilt. About 500 kays after i picked it up it shifts dangerously hard and immediately into all gears at around 20-40 mph, converter also locks immediately. The speed sensor in the box was replaced with the rebuild but I'm having it replaced again this thursday just in case.
Just for the record I cooked it on the beach a while back, the speed sensor was replaced with the rebuild as it was doing the above, the od light also flashes when this occurs, before and after the rebuild.
Prior to cooking it never had an issue.
What could be causing it? I'm starting to worry it cant be fixed, have done a google and tried a couple of things mentioned. Code says wiring issue associated with speed sensor in box.
Ford Super Duty (1999-2016) :: 2002 F250 - Transmission Shifting Hard
I have a 2002 ford f250 with the 7.3l diesel. I recently installed a ts performance chip. On my pcm. And after i first tried all the different stages I didn't like how my transmission was shifting hard. So I contacted the manufacturer and he told me they could reprogram the chip for smoother shifting. So I removed the pcm and removed the chip. But when I went to reinstall the pcm I bent one of the pins on the pcm some how.
So I took it back out and straightened the pin with pliers . i reinstalled it back in the truck. Only to find when I reattached the battery cable I have no power to anything ignition ,horn, lights,Cigarette lighter etc. So my question is if the pcm is bad, or not contacting properly due to the pin being messed up. would that have anything to do with the lights and horn and all that? I suspect its the gem bsm or Vsm. Whichever one my truck has. But really not sure because everything worked fine just 20 min b4.
Ford Super Duty (1999-2016) :: 2001 F350 - 4R100 Not Up Shifting To OD
Bought truck drove it 240 miles on interstate 80 mph no problems---2001 F350 4x4 auto. Next morning backed out drive and trans fluid trail 6 inches wide. Didn't leak in forward gears (at that time) added fluid and drive to town shifted fine.
Next day gonna drive 150 miles to check out leak. (Son was driving it) said it wouldn't go over 40 mph. Revving high. Hauled truck here on trailer and pulled tranny. Rear housing cracked just before 4x4 adapter. (This trans was rebuilt 10k miles ago) ..
Got used 4R100 from friend who replaced only because he built one for his truck. It was shifting fine etc when pulled 6 months ago. Used cracked trans TC and installed. Test drive no 4th or OD. Pulled trans put TC that came with trans in. Still no OD. Put on scanner while driving. Trans is being commanded to shift to OD but not up shifting. 45mph at 2400rpm.
Pulled plug to solenoid pack inside trans ( this should make trans default to OD / limp mode) still no OD and won't go over 45.
Pulled OD button checked wires inside steering column. All looks great. Not even a heavy rub mark.
Should I replace the coil pack in trans? Where do I go from here? Again this trans was known to be good when pulled 6 months ago.
Ford Super Duty (1999-2016) :: 1997 F350 - Codes P0327 And P0629 - Hard Shifting But No O/D Light Flashing
I have a 97 F350 5.8 with E40D trans. I bought the truck with it shifting hard thinking maybe a simple filter/fluid change would fix it. It may have worked a little but did not fix the issue. There were 3 or 4 codes that I have already cleared up with new parts. I am still getting a 327 (something with EGR?) and 629 (Converter clutch control circuit failure). These show up in KOEO and KOER self test. The O/D does not flash ( bulb does work).
Parts that have been replaced: VSS, MLPS, new connector going into solenoid pack (tabs were broken), TPS. Removed the trans wiring harness and there is no damage or loose connections. When I replaced the solenoid connector I noticed there was some trans fluid in the connection. I cleaned it the best I could and reinstalled with dielectric grease.
The truck runs fine and shifts in and out of every gear fine its just shifting hard. If I unhooked the battery it will shift perfect for 5-10 minutes but then the hard shifting returns.
The only other thing I can find with my research is maybe the solenoid pack needs replaced. I figured if I take it somewhere they are going to want to rebuild/replace transmission. It seems like it can't be something very major since it will shift fine when reset...
Ford Super Duty (1999-2016) :: 2001 F350 - ABS Light Comes On - Metal Grinding Sound
2001 f250 7.3 crew
So, Saturday my abs lite comes on. Later that day I hear metal to metal sound for a couple of secs then it stops. Then the next day while driving I get intermittent sounds that sound like I'm dragging metal down the pavement. I see nothing but I'm thinking hub bearing. (Needle)
I remove the hub assembly from the knuckle and can find nothing wrong. I even picked up a new hub just on case. Now I'm stumped. Can't figure out what the sound was or is. Axle has a little play going into the housing but figure it would have due to the only thing holding it in place is the hub.
The only thing left in the area that could make the sound is major --the actual gears to to the front end. If the bearing isn't causing the metal grinding sound I've no other idea other than that....
Ford Super Duty (1999-2016) :: 2001 - Long Hard Starts No Matter What The Temp Is Outside
My truck is 2001 F250 with the 7.3 I have AFE intake, TS 6 position chip, Stage 1 Auto Tranny, 4in Exhaust all the way down. New glow pugs as of last week as well as uvchs and gp relay. Also has a new hpop line. New compression sleeves for fuel lines, riff-raff fuel banjo bolts and fuel pressure regulator.
I am having a hard start issue no matter what the temp is outside, unless it plugged in. Once it starts its good unless it sits for more than 5 hours.
Batteries have tested good, glow plugs ohm at 1.3, gpr 12.83 at batt side- once on it 11.9. All fuses are good. HPOP res is showing at about 3/4" down from top.
***Wires going to the MAT sensor are showing through at the connector, not sure if this could be a problem...if so why???
****Noticed some oil in the ICP, cleaned and unhooked will check start tomorrow to see if this works with long start as truck is plugged in.
Will also be putting a new fuel filter in and double checking oil level in the am. I do not have a scanner tool and am doing the best I can before I take it in to ford to diagnose.
Ford Super Duty (1999-2016) :: 2001 F350 - Grinding Noise When Drive Slow And Especially Turn To The Right
Have an f350 4x4 diesel that when I drive slow and especially turn to the right it makes a grinding noise. It seems to either go away or just gets muffled by road noise when cruising. The ball joints were bad so I replaced them and I figured with this especially when I turn right it had to be a wheel bearing so I replaced both of them and still same thing. Don't want to throw money at it hoping to fix the issue. Also front duff is full of oil.
View 5 RepliesFord Super Duty (1999-2016) :: 2001 F350 V10 - Hard To Find Gear
Got an '01 f350 v10, auto. When using steering column shifter tends to be hard to find reverse and drive. Is it something in steering column selector or is it in tranny? The truck has 40,000 miles on it. Have a parts truck also so just trying to figure out where to start first.
View 3 RepliesFord Super Duty (1999-2016) :: 2001 F350 - Faint Grinding Noise In Left Front Wheel
I got a 2001 f350 got a noise in my left front wheel i know its not the wheel bearings, it only makes the noice when the locking hub is unlocked i did jack the the truck up and spun the wheel got a faint grinding noises form what seems like the locking hub so my question is bad locking hub or needle bearing holding the axle shaft??
View 3 RepliesFord Super Duty (1999-2016) :: 2001 F350 Truck Won't Do Over 30 MPH / Engine Starts To Sputter And Back Fire
I recently bought a 2001 f-350 xl 4 door with the 8 foot box it has the 5.4L triton v8. I was heading to a job up in northern Alberta about 10 hours away from where I live. On the drive I lost control of the truck on some black ice I was doing about 50 miles I went into the ditch but nothing crazy drove right out after. Now my truck won't do over 30 mph the engine starts to sputter and back fire I loose all my power, what's going on. At idle she revs fine but as soon as I put her into drive it's like she wants to die what can it be?
View 6 RepliesFord Super Duty (1999-2016) :: 2001 F350 - Vibration / Grinding On Front Driver Side After Partial Rebuild
2001 f350 4x4 dually 7.3 powerstroke, I recently replaced the hub assembly, stub shaft and seal, u joint, ball joints on the front drivers side and now periodically the truck makes a grinding growling vibration coming from front drivers side and stops after hitting a bump...
View 3 RepliesFord Super Duty (1999-2016) :: 2001 F350 - Parking Brake Pedal Is Extremely Hard To Push
I have a 2001 F-350 Diesel 4x4 crew cab 8ft bed dually 7.3 diesel 6 speed. The issue is that the parking brake pedal is extremely hard to push. One day it pushed down and ratcheted into a locked position as normal and the next day I couldn't push it more than an inch down. I have rear disc brakes with internal drums in the rotors for the parking brake assembly. I replaced the shoes and hardware (which were fine) and I still have the same issue. I removed the front single cable from where it splits into the two rear ones and the foot pedal depresses smoothly and with the touch of a finger with no load on it. What else is it? The only other thing is one of the rear cables unless I am missing something?
View 5 RepliesFord Super Duty (1999-2016) :: 2004 F350 - 4wd First Not Shifting To 4lo
On dads 04 f350 the 4wd first wasn't shifting to 4lo. Would do 4hi and 2wd fine. Then motor on t-case went bad. Replaced motor 2wd and 4hi still good still no 4lo. Then just 2wd so we unplugged t-case motor and power probed motor got it to do 2wd, 4hi, and 4lo. So we thinking bad dash switch but power probed it and its working fine. So we r thinking VP4C3F-14B128-A/ chassis computer bad just behind/above glovebox. R there any test we can do to confirm its bad? We called local junk yards to see bout getting one, nobody had one. If this is indeed bad where is cheapest get one? What all years use this certain chassis computer??
View 5 RepliesFord Super Duty (1999-2016) :: Transmission Will Not Go Into Forward Gears
I have a 1999 F-250 4X4 7.3 lit Diesel engine. My problem is my transmission will go into reverse great no problem but it won't go forward. I have no problem rebuilding the transmission if that's what it needs, I just want to make sure there isn't a electrical issue from the PCM first?
View 14 RepliesFord Super Duty (1999-2016) :: F350 Making Grinding Noise Every Once In A While
My 1999 Ford F350 Dually 4x4 started making a grinding noise every once in a while about 3 weeks ago. Now it is doing it quite often, randomly as I am driving. I do notice the noise stops when I stop the truck, or when I flip the switch to 4x4 and back while driving.
View 1 Replies