Ford Super Duty (1999-2016) :: 1995 E350 - Shifting From First To Second Is Very Hard
I recently bought a van that has a hard shift problem. It is a 1995 E350 with a diesel. If I take off from a stop without babying the throttle, the shift from first to second is very hard. Second to third is hard but not as violent. What might be happening?
View 9 RepliesFord Super Duty (1999-2016) :: 2001 7.3L F350 - Transmission Starts Shifting Hard And Grinding Gears
My buddy's 2001 7.3L F350 has had 3 transmissions. Rebuilt and used. Once the new trans is in he goes like 15 miles and then is starts shifting hard and grinding gears. What this could be?
View 8 RepliesFord Super Duty (1999-2016) :: 1997 F250 - Hard Shifting?
I have a 1997 f-250 heavy duty with the 7.3 I have been having problems with very aggressive and hard shifting. While it is acting up the overdrive light on the shifter blinks. This problem goes away and it might be good for a month or so, But it always comes back. I have had it to a professional trans tech, He replaced a part on the side of the tranny. I thought it was fixed, But now it is acting up again.
View 4 RepliesFord Super Duty (1999-2016) :: 2000 F250 - Shifting Late In All Gears / OD Indicator On Shifter Blinks From That Point Forward
My 2000 SD 7.3 has developed a quirk. For some reason the trans has decided to shift late in all gears. This only happens once, then resumes shifting normally. However the OD indicator on the shifter blinks from that point forward. Once the engine is shut down and restarted. The sequence starts again. Late shift, through the gears, once, then shifts normally with light blinking. Fluids are up and clean.
View 4 RepliesFord Super Duty (1999-2016) :: 2002 F250 - Transmission Shifting Hard
I have a 2002 ford f250 with the 7.3l diesel. I recently installed a ts performance chip. On my pcm. And after i first tried all the different stages I didn't like how my transmission was shifting hard. So I contacted the manufacturer and he told me they could reprogram the chip for smoother shifting. So I removed the pcm and removed the chip. But when I went to reinstall the pcm I bent one of the pins on the pcm some how.
So I took it back out and straightened the pin with pliers . i reinstalled it back in the truck. Only to find when I reattached the battery cable I have no power to anything ignition ,horn, lights,Cigarette lighter etc. So my question is if the pcm is bad, or not contacting properly due to the pin being messed up. would that have anything to do with the lights and horn and all that? I suspect its the gem bsm or Vsm. Whichever one my truck has. But really not sure because everything worked fine just 20 min b4.
Ford Super Duty (1999-2016) :: 2002 F250 - Hard Shifting From 1st To 2nd When Cold
I have been having hard shifting from 1st-2nd when cold. Rpms up to 2000 and let off then goes into 2nd. After that, she shifts fine and shifts well until next morning when she sits overnight. Build tag is August 09, 2001, so no old mechanical diode? Took a sample of fluid and it is dark red (pic attached) and smells like hydraulic fluid...I don't think it smells burned. Does it sound like the calve body 1-2 shift or solenoid pack or needing rebuild?
View 3 RepliesFord Super Duty (1999-2016) :: F250 - Trans Shifting Hard / OD Light Flashing / Code P0720
Just got the transmission rebuilt in my truck and other then shifting hard sometimes it has been doing great, Hooked it up to the goose neck this evening and everything was fine then went to back it up and pull it forward and after a short distance the od light was flashing and when i ran a check on it it was p0720? The transmission has less then 1000 miles on it?!?!? 1999 Ford F-250 7.3 Automatic....
View 5 RepliesFord Super Duty (1999-2016) :: 2002 F350 - Shifting Really Sluggish Between 1st And 2nd Gears Only
2002 f350 7.3 ... problems started all of a sudden one day. I have an edge evolution tuner in my stroke. I have it set to make all of my shifts firm. One day it started shifting really sluggish between 1st and 2nd gears only. It don't do it all the time, but it does it more often then it doesn't. I have also noticed when i come to a complete stop and then start out again it seems that it doesn't downshift all the way back to first and when i hit the gas it seems to kinda be stuck between gears and it barely moves until i get the rpms up before it will ease its way into 2nd and the converter locks up.
It shifts a through all the other gears just fine nice and firm like it should, its just the shift between 1st and 2nd. Im wondering if maybe it might be the speed sensors or maybe the tranny filter is getting clogged up? The fluid in it is still nice and red and up to the level it should be. I just bought the truck in october and the fluid was nice and red when i bought it, but who knows if they changed the filter. I have had NO tranny problems with it up until a few days ago when this little problem started.
Ford Super Duty (1999-2016) :: 2008 F250 Running Rough In Low Gears - CEL Came On
2008 F250 5.4L 150k. My truck has been driving pretty rough in low gears, rough idle, and today the check engine light came on then getting on the interstate the light started blinking. I ran the code it came back 0307,300,308,300. After doing some research on here, I've come to the conclusion to change out the coils on 7 & 8. Questions are, should I change plugs as well? And how important is it to keep all the boots (of all 8) the same color (brown or black)? And should I expect to change all the rest soon?
View 1 RepliesFord Super Duty (1999-2016) :: Transmission Shifting Hard Between 2 And 3 Gear
The tranny is shifting really hard between 2 and 3 if I feather the throttle it can be a little less of a jolt but still enough none the less iv never done a filter and fluid change as I just got it it has 235000 miles 99 v10 super duty 4x4....
View 8 RepliesFord Super Duty (1999-2016) :: 4r100 Transmission Shifting Hard
Recently I have had an issue with my auto which was just rebuilt. About 500 kays after i picked it up it shifts dangerously hard and immediately into all gears at around 20-40 mph, converter also locks immediately. The speed sensor in the box was replaced with the rebuild but I'm having it replaced again this thursday just in case.
Just for the record I cooked it on the beach a while back, the speed sensor was replaced with the rebuild as it was doing the above, the od light also flashes when this occurs, before and after the rebuild.
Prior to cooking it never had an issue.
What could be causing it? I'm starting to worry it cant be fixed, have done a google and tried a couple of things mentioned. Code says wiring issue associated with speed sensor in box.
Ford Super Duty (1999-2016) :: 2011 F350 - Transmission Shifting Hard From 3 To 4 Going Up And 2 To 1 Going Down
I have a 2011 F-350 6.2L that has extremely hard shifts from 3 to 4 going up and 2 to 1 going down. Sometimes on downshifts it feels like something has ran into the back of the truck. I had the computer updated when the truck had approximately 40,000 miles on it and he assisted a little bit. The truck now has 140,000 miles and it is back to shifting horribly. I put it in the shop at the dealer on 30 December 2013. The dealer says that the problem is that the shift solenoids need to be replaced but that they are not available. The truck is still sitting at the dealer and I am being told that the parts should be available mid February.
View 10 RepliesFord Super Duty (1999-2016) :: 2012 F250 - Grunt When Changing Gears / Mushy Brakes
On the surface, the F-250/350 seems to have great brakes: big rotors, vented front and rear, and dual-piston calipers front and rear. But, I have two problems:
One is the annoying 'grunt' the brakes make every time you change from Park to Drive, or Park to Reverse, or Drive to Reverse. Its as if under normal brake pressure, the brakes cannot hold the truck from moving against the torque convertor engaging. It's not just my truck, I've heard older SD's with the 5.4L or diesel do this too. If you push the pedal really hard, it won't grunt.
The second problem I think is the root of the first: mushy brakes. Maybe I'm just used to driving european cars with firm brakes, but every time I apply my truck's brakes, it feels like I need to bleed the system! The truck does slow pretty well, and I realize it's heavy, but how can the pedal feel be improved? Maybe replacing the rubber sections with braided stainless?
Lastly, the truck has a 'hill-hold' feature which is retarded in an automatic transmission. My problem with it, is that sometimes it sticks on...engage drive, the truck won't move...a second later its like something gets unstuck and the truck kind of lurches forward.
Ford Super Duty (1999-2016) :: 1995 F250 - Trans Locked Up Motor?
I just bought a 95 f250 4x4 with the 460. The guy i bought it from had a trans slipping towed it to the shop when the shop went to pull it in they started it put in gear and engine died. The motor is now tight w no movement either direction with a bar obo it. Is it possible the trans is holding the motor tight? What can I do?
View 10 RepliesFord Super Duty (1999-2016) :: 2003 F250 - Surge / Lag When Shifting
I just got 03 f250 with 6.0 and when shifting has a weird surge/lag thing happening. Reminds me a little of the old 7.3 surge when it was just started on a cold day. Seems to be worse in higher gears.
View 2 RepliesFord Super Duty (1999-2016) :: Hard Shifting - Slight Bit Of Clinking Noises Every Time Started From A Stop
Well shoot, not even 120k on the odo and I've had my first major problem with the truck, and the one thing I hoped wouldn't be an issue, especially since I don't work my truck hard and 95% is driving unloaded highway as a daily driver.
Last time I drove it coming home from grocery store there was a big racket from down under (transmission area). It instantly didnt feel right - there was a slight drag even when the clutch was in, but rolled fine when I pulled it out of gear entirely. Was VERY difficult to go into first gear. Other gears shifted ok but some of them felt hard too. Would not go into reverse at all!. Slight bit of clinking noises every time I started from a stop, but made it home ok and things seemed to ease up as I went. Today, seems to be shifting fine, reverse works and everything.
Now for several years I've had a noise that I couldn't figure out. I am guessing it's related because it sounded like was coming from tranny area. Often, when starting out from a stop, there was a bit of clinking noise like a couple tin pie pans rattling together just as the clutch started to go. I kept thinking it was loose heat shield or something clanking just under the initial vibration of getting going. Never did find anything loose. I'm guessing it's internal.
I've called a couple local shops and so far no one wants to mess with it. Dam this sucks i hoped the MT would be more reliable, not the first thing to go. I myself have never messed with any aspect of a transmission, though I not opposed to learn however I was hoping to take this on an out of state trip end of May, and I'm not going to have much any free time between now and then.
Ford Super Duty (1999-2016) :: 2003 F250 - Harsh Shifting / Sluggish / Loss Of Power
I have a question for everyone out there with any insight of the harsh shifting with these trucks. I have a 2003 f250 super duty with the 5.4l and 126,000 miles on it. The problem I'm having is some weird shifting that has been going on over the last six months and I feel like I am just throwing money at this problem. My truck shifts hard from 2nd to 3rd and from 3rd to 4th with the most violent shifts being from 3rd to 4th! Between shifts is where it Is sluggish I mean if I am not on the throttle from those shift points I switch from driving a truck to a geo metro it is night and day with the felling of loss of power!
I have had it scanned at my local ford dealership and had a full diagnostics done and all I got was "it's since truck and a nice bill to come with it" they couldn't find a thing. So far I have all new motorcraft plugs, cops, changed fuel filter, had my catalytic converter checked if it was clogged,run on two different power balance tests! Still nothing! So now I'm lost I have heard things about these trannys and the lock up but I was told this only had to do with overdrive and it wouldn't happen at other gear changes. I still drive it everyday I have just figured out ways to calm it down if I stay off the gas when it's about to shift for a couple seconds then get back on the gas it is like it never happened.
Ford Super Duty (1999-2016) :: 2006 F250 - While Shifting Into 4x4 A/C Heat Blows From Defrost Vents?
2006 F250 with the dash controlled 4x4. I typically keep the front hubs locked on this truck. I have recently noticed that when shifting into 4x4 that the a/c or heat will switch from blowing out of the vents to blowing out of the defrosters. Any clues how to fix this?
View 1 RepliesFord Super Duty (1999-2016) :: 1997 F350 - Codes P0327 And P0629 - Hard Shifting But No O/D Light Flashing
I have a 97 F350 5.8 with E40D trans. I bought the truck with it shifting hard thinking maybe a simple filter/fluid change would fix it. It may have worked a little but did not fix the issue. There were 3 or 4 codes that I have already cleared up with new parts. I am still getting a 327 (something with EGR?) and 629 (Converter clutch control circuit failure). These show up in KOEO and KOER self test. The O/D does not flash ( bulb does work).
Parts that have been replaced: VSS, MLPS, new connector going into solenoid pack (tabs were broken), TPS. Removed the trans wiring harness and there is no damage or loose connections. When I replaced the solenoid connector I noticed there was some trans fluid in the connection. I cleaned it the best I could and reinstalled with dielectric grease.
The truck runs fine and shifts in and out of every gear fine its just shifting hard. If I unhooked the battery it will shift perfect for 5-10 minutes but then the hard shifting returns.
The only other thing I can find with my research is maybe the solenoid pack needs replaced. I figured if I take it somewhere they are going to want to rebuild/replace transmission. It seems like it can't be something very major since it will shift fine when reset...