Ford Super Duty (1999-2016) :: F250 - Noise Like Fan Blades Hitting Coming From The Torque Converter
Switch out a 5.4 in a F-250 4X4 4 my neighbor now I have a noise like fan blades hitting coming from the torque converter it goes and comes and hits good in reverse...
View 9 RepliesFord F-150 (2004-2008) :: Torque Converter Clutch Solenoid Plug Location
Where is the plug on the transmission to disconnect the TCC solenoid? I am trying to diagnose a lockup issue and need to disable the clutch from engaging for a test run.
View 1 RepliesFord Super Duty (1999-2016) :: 2000 F250 - Code P1746 - EPC Solenoid / Open Circuit
I have a 4r100 in my 2000 f250 7.3. I am getting a P1746-EPC Solenoid, open circuit. Does this mean this particular solenoid in the solenoid body has failed and should i replace the solenoid body?
View 3 RepliesDodge - Avenger :: OBD Code P0743 - Torque Converter Clutch Solenoid
I have a 1997 Dodge Avenger ES that reads code P0743 Torque Converter Clutch Solenoid. I've replaced the transmission control module, and filter. I've called the Dodge dealership and asked if the new transmission control module needs to be programmed. The service department said "Possibly" I said "Well it's shifting better than before. If there wasn't any firmware on it what would it do?" He said "My guess it that the car wouldn't shift." I asked if the Torque Converter Clutch Solenoid visible once you remove the filter. He said "I'm not sure." Clearly, my car isn't going there. Then asked to be transfer to the Parts department to see if there was a part called Torque converter clutch solenoid. That answer was "No" there isn't a part listed called "Torque Converter Clutch Solenoid". What should I do or try?
View 9 RepliesFord Super Duty (1999-2016) :: Substantial Vibration When Torque Converter Locks
I have a bone stock (other than exhaust) F-250 SD, 6.0 auto, 185k miles. I have a substantial vibration when the torque converter locks - about 50-55 mph. Once the transmission warms up (i.e. 4-5 miles from a cold start) the vibration goes away and the transmission performs flawlessly. Backing out of the throttle and allowing the TC to unlock makes the vibration go away, as does shifting into neutral. There is no noise, just a vibration that will shake the whole truck. Transmission fluid looks good, and showing full. Have had the truck about 4 months, and have not flushed or replaced the filters on transmission.
I've seen a couple of similar threads on vibrations, but not one where the vibration will completely go away. I'm thinking replace the torque converter but wanted to get more information from the experienced experts that know these 5R110s better.
2007 F-250 King Ranch 6.0 PSD, 5R110W, 4" Turbo Back, Otherwise bone stock, 185k.
Ford Super Duty (1999-2016) :: Noticeable Torque Converter Lockup In 5th Gear
When running up through the gears under normal acceleration I can feel almost a double shift in 5th gear. It doesn't occur using tow/haul so I assume it is the TC locking up. Everything else seems fine. Truck has 9k miles, mostly towing. 2016 6.2 ....
View 6 RepliesCamry :: Engine Code P0741 - Torque Converter Clutch Circuit Solenoid
How can I fix the P0741 engine code? Vehicle has 100k mileage.
Some of the on and off symptoms: loss of power, doesn't go over 40mph on the bridge, rpm dramatically goes high at low speed, lower mpg.
I did a tune-up: [URL] .... 2Bplugs, engine, coolant, [URL] .... 2Bfluid, steering, ignition coils, short ram intake filter cleaned.
Ford Super Duty (1999-2016) :: 2007 - Won't Shift If Does Then Slams Into Gear - Torque Converter?
I have an issue to where every once in a while my truck will not shift and when it does shift it slams into gear, and my overdrive light flashes and then I'll turn the truck off let it sit and crank it back up and it drives fine and the overdrive light is off. It shifts normal and smooth other than when this happens. Not sure if it is my torque converter or maybe a solenoid or what. My truck is an 07 f250 6.0 with 192,000.
View 5 RepliesFord Super Duty (1999-2016) :: 2002 - Torque Converter Slip / Stall - No Lock Up
I have a 2002 7.3 with the 4r100 173k miles. If your nice to it she drives fine, but if you get on it the torque converter will slip/stall kinda revs up like 300 rpm then slams really hard between 1st and 2nd. Other gears work fine. I've only had it not happen like 10 times since I've owned the truck ..... I don't really beat on it except for towing which I'm starting to do a lot of. Wondering if putting a new stock torque converter in it is worth it.? Not gona blow the bank on a TC unless I'm putting a brand new trans in the truck. Which I don't think it needs in the near future.
View 14 RepliesFord Super Duty (1999-2016) :: 2000 F250 - Installed Clutch Now Grinding Noise?
2000 Ford F250 crew cab 4 x 4 with 7.3. 6 speed transmission.
I just had a new clutch installed and now I am have a grinding noise when putting it into 1st gear and when I change from granny to first it will grind also. I did not have this issue before having the clutch replaced.
I have also just had a new hydraulic clutch kit installed.
Ford Super Duty (1999-2016) :: 2000 F250 - Clutch Not Disengage - Stiff Pedal
I've got a 2000 F250, 5.4L 4x4 with the ZF5 5-speed transmission. Three years ago I replaced the complete clutch assembly, pressure plate, throw-out bearing, etc, and had the flywheel re-machined. Put it back in and all has been well. Only has about 15k miles on it. Earlier this week I went to drive it and all of the sudden it started getting harder to shift and by the end of the trip the clutch will not disengage at all when I push the pedal in.
Furthermore the pedal is much harder to push than it always has been. Checked the reservoir and it's fine. After some searching it seems to most likely be an issue with the master and/or slave cylinder either needing to be bled or replaced. Further reading revealed that bleeding and recommends just replacing the whole system, so I've priced that out. Was it a master/slave issue? Anything else I should check in case it isn't?
Ford Super Duty (1999-2016) :: 2001 F250 V10 Won't Start - Solenoid Located?
My 2001 F250 will not start (clicks). I verified its not the battery and even tried to jump start it. I have never replaced a starter- but before I do that I read where there is another solenoid under the hood somewhere. I always thought there was just the one on the starter itself.
Two questions:
1. where is that other solenoid located and should I replace that first?
2. How difficult is it to replace the starter? I am pretty handy.
The issue is that I cannot get it towed easily - I just need to get it started at least once since my plow is still installed and it's hooked up to a trailer..
Ford Super Duty (1999-2016) :: F250 Has P7147 Error - PWM Or Non-PWM Solenoid Pack
99 F250 Super Duty 5.4 has a p7147 error. Traced all wiring cant find any short. Bought reman solenoid pack # are f81p-7g391-cb with green cover my old one in trans is f81p-7g391-ba with blue cover. Are these interchangeable? Have tried to read up on pwm & nonpwm and getting confused.
View 2 RepliesFord Super Duty (1999-2016) :: 2010 F250 - Vacuum Solenoid Not Getting Electricity?
I have a 2010 f 250 super-duty and i cannot get vacuum past the solenoid mounted on top of the radiator. Ford has given me nothing but bad advice. I know i have a vacuum leak after the solenoid and need to replace the lines going to the two hubs but when i switch on the 4wd and hook up a vacuum gauge the vacuum is good up to the solenoid about 12 inches. i constantly have 12 volts going to the center lead but nothing else in the other two leads either in 4 high, 4 low, or 2wd. Am I missing something here? shouldn't there be a voltage change when i turn the switch to 4wd to actuate the vacuum solenoid to let the vacuum pass thru the solenoid? I have tried replacing the solenoid but that did not work. Also use rubber vacuum line and make at down to the hubs?
View 4 RepliesFord Super Duty (1999-2016) :: 2006 F250 - 4 Wheel Drive Solenoid Location
I have a 2006 F250 Super Duty w/ turbo Diesel. Took to dealership for "hopping" feeling when turning sharp. Was told that 4 wheel drive solenoid was bad. Where this solenoid is located? I know I can fix but want to know where it is located.
View 6 RepliesFord Super Duty (1999-2016) :: 2000 - Torque Settings For Lug Nut?
What torque setting I should use for lug nuts on a 2000 F-350 dually?
View 7 RepliesFord Super Duty (1999-2016) :: 2011 F250 - CEL On - CAT Converter Failing At 39k Miles?
Recently my 2011 f250 sd 6.2s check engine light came on so I took it to my local dealer it was throwing a p0430 code, they said bank 2 cat converter wasn't do it's job so it needed to be replaced. I am concerned that there is an underlying cause of the premature cat fail. I pushed the issue with the service manager and he told me that's all they could do was replace the cat and refused to check anything else on the truck. Is this common? The truck runs and drives fine. I'm just concerned that they are just throwing parts at it to get it out the door.
View 5 RepliesFord Transmission :: 2000 F250 7.3 - Trans Slipping - Torque Converter?
I was driving my 7.3 down the road and it started acting like the trans was slipping, it revved up and tried kicking down a couple times and when I slowed down and went to speed back up it just had no power coming through the trans to the wheels it just revved. I put it in neutral and it idled up for about 5 seconds. I put it in park n shut it down. I fired it back up after looking everything over and it moved about half mile down the road and no power to the wheels again. The trans is full of fluid, is there a sensor that could of went bad or just the torque converter or the entire thing shot? Only owned my truck 6 months has a trans and motor swap already from previous owner. 180k on current motor n Trans. 382k on my truck. t6 4" turbo back banks exhaust only mods I know of.
View 11 RepliesFord Super Duty (1999-2016) :: F250 - Clutch Needs To Go All The Way To Floor
I Have a 1999 f250 7.3 diesel with the zf5 manual transmission and to shift gears I need to push the clutch all the way to the floor. Could this possibly be the slave and master cylinder or is it the clutch?
View 14 Replies