Passat (B5) :: How To Attach Inner Tie Rod Boot To Steering Rack
I'm going to replace tie rods assembly. I have a question about inner tie rod boot. How do you attach it to the steering rack? No room there, horrible access.
View 1 RepliesPhaeton :: Leaking Steering Rack - Oil Pouring Out Of The Boot
I'd noticed an oil leak drivers side and upon investigation it appears the rack has developed a leak. I lifted the car on the vehicle lift and when I did noticed oil pouring out of the boot surrounding the steering linkage coming from the steering rack. With the tires dropped the full amount this created a tilt of said boot allowing the oil that had filled the boot to drain out. My conclusion is the rack has developed a leak with the boot being full of oil.
I did a "steering rack" search but nothing of value appeared.
Lexus RX 2004-09 :: Power Steering Rack Seems To Be Leaking Through Rubber Boot
I was replacing the oil in the transfer case and came across this under the passenger side. Power steering rack seems to be leaking through the rubber boot, but I have not noticed anything on the garage floor in recent months...
Can the boot itself be replaced? I hate to think the whole system needs to be replaced.
Ford Ranger / B-Series :: 1996 - Power Steering Replacement
I'm in the middle of replacing my pump. With the new pump are a plastic washer and a small rubber o-ring but no instruction where they are supposed to go. They didn't know at auto zone and I haven't heard them mentioned on any youtube video. I found a crushed torn up washer similar to the plastic one in my catch pan. Maybe it is supposed to go in around the high pressure hose connection.
View 6 RepliesGolf IV / Jetta IV :: 2001 VR6 - Power Steering Rack Replacement
I need to replace the power steering rack on my car. Mech wants 300+parts. I supply the parts. Is there a different rack for the vr6 VS the I4 jetta?
View 1 RepliesCamry :: Passenger Side Boot Replacement On Power Steering
What is the procedure for changing the passenger side boot on the power steering? I've read the Chilton repair manual, looks too easy.
View 6 RepliesFord Ranger / B-Series :: 2.8L V6 Valve Stem Replacement?
I have a 1984 ranger with the 2.8L and I am doing the valve stem oil seals.
I have instructions from the ranger station. And I have access to mitchell1 and chilton online.
Also I read somewhere about better settings to use for valve lash? The truck has about 80,000 miles on it.
Ford Ranger / B-Series :: Fuel Filter Removal / Replacement
I know where the filter is, i know how to bleed off the pressure. Im wondering if those clips are easy to slide off to remove the filter from the lines?
View 7 RepliesFord Ranger / B-Series :: 1999 - Clutch Slipping - Replacement?
My clutch is weak and slips sometimes and I need to replace it. ,I have replaced the clutch disc in other trucks but never a Ranger.
1999 3.0, 5 speed stick, Extended cab....
Ford Ranger / B-Series :: 2003 - Replacement Of Outside Mirror Glass?
Is it possible to replace just the glass on the outside mirrors on a 2003 Ranger?
If so, how is it done?
Ford Ranger / B-Series :: 1999 - Rear Main Replacement?
I'm an experienced home mech, not really worried about doing the job. Just curious if there is any pitfalls I need to know about, or a trick/tip that may make the job easier?
View 8 RepliesFord Ranger / B-Series :: 2011 - OEM Radio Unit Replacement
I have a 2011 Ranger. It came with Sirius radio which works with the AUX button on the head unit. This setup is not what I am use to. Anyway I want to replace the OEM unit with an aftermarket. My question is will this AUX connection effect an aftermarket radio connection?
View 11 RepliesFord Ranger / B-Series :: 1984 V6 - Electric Choke Replacement
I've got a '84 ranger that idles super fast for about 30 minutes after a cold start. The truck has been in the family since new and has done it since day one. I am wondering if replacing the electric choke or choke pull down would work. I've got a electric choke replacement but the cover place looks to be attached with rivets not screws. How to remove the choke?
View 3 RepliesFord Ranger / B-Series :: 2006 - Door Mirror Replacement?
Replacing their door mirror with an aftermarket door mirror and not been happy with it?
I have a non-powered door mirror. if I understand my FoMoCo Workshop Manual correctly, I should be able to replace the exterior mirror glass without the need for a completely new mirror assembly.
Ford Ranger / B-Series :: 1983 - TK5 Shifter Assembly Replacement?
My 1983 Ranger is in the shop. I'm being told that I need to replace the shifter assembly. I understand that this is a Mazda part, from a TK5 transmission. These parts are interchangable between bronco ii's of the same era.
View 1 RepliesFord Ranger / B-Series :: 2003 - Repeated Serpentine Belt Replacement
2003 3.0 ranger... This will be my 3rd time replacing serpentine belt and if needed 2nd. time for idler, tension pulleys...NOT SURE WHAT TO DO, should i replace parts again?
View 5 RepliesFord Ranger / B-Series :: 1994 - Slave Cylinder Went Out / Clutch Replacement
1994 Ranger 4.0 XLT 4X4. My slave cylinder went out so I thought I would put in a spec clutch in while I'm in there. What do I have to pull off to get the 5 speed tranny / transfer case down? I don't want to pull off what I don't have to but I don't want to make it hard either. No Chilton on hand and I did a search on clutch but found no thread for replacement.
View 2 RepliesFord Ranger / B-Series :: Misfire Over 65 MPH - Not Starting After Fuel Pump Replacement
I've got a 2000 ranger w 158k miles, been having issues with a misfire over 65mph, and it's been throwing a check engine O2 sensor code. One of the probable reasons for the O2 code read low fuel pressure... so my husband got the bright idea of replacing the fuel pump.
That turned out to be a big story in and of itself. BUT we got it replaced with one that works, however.... now it won't start!!! You have to pump the gas and like crazy and hope that it'll start, it will eventually... but not without a bunch of coaching.
Once it's running, it's running ok. The first day after replacing the pump it was AWESOME, ran like it used to years ago, no misfire, smooth as could be, no rattle, no check engine light. But it all came back it's misfiring again, rattling when you accelerate, and the check engine is back on. I haven't had a chance to go run and get the codes ran again, maybe tomorrow I'll be able to do that in between errands. Oh, and we are gonna replace the fuel filter at some point in this week...
Ford Ranger / B-Series :: 2001 - ABS Light Is On / Front End Joints Replacement
I have a 2001 ranger 3.0 auto 2wd and the abs light is on. this is what i have done so far. I had to replace all the front end joints so i took the front sensors and ohmed them and got continuity and voltage when i ran a metal past them and the same for the rear on the diff. so i figure they are fine. the wires to the frame look ok and i the truck has no damage so i figure the wires are fine.
I checked to see if the fuses are installed after I got the fuse layout and all the fuses are there and good. So I took it to advance auto and it came back with everything bad sensors motor controller and if anything else could be bad with the abs it said it was. I told them it is impossible for all of it to be bad. so it must be the controller. No I'm thinking the controller it the box attached to the abs pump and lines at the power distribution box under the hood.
Can I just remove that box and replace it with little difficulty or will i have parts fly out all over the place if i remove that box from the pump? All the pictures i see the the abs controller don't look the same as the one i have on my abs pump.