Ford Ranger / B-Series :: 2000 - Stall In Park And Reverse?
Why my trucks engine is cutting out. idles fine and runs fine when on the road, it only stalls in park if i rev the engine, and it stalls immediately when i put it in reverse.
I took it to a shop and they scanned it and said it was a o2 sensor problem. replaced both o2 sensors(they were both bad) but no luck there, still having issues.
Ford Ranger / B-Series :: Reverse Lights Fuse 26 Blowing
Since last summer my truck keeps blowing fuse 26 and then I have no reverse lights. If I replace the fust its ok for a bit but blows again the same day sometime. The book says its the fuse for revers and overdrive. The overdrive button on the tree shifter stops working too but the truck does not seem to be revving any higher so I think the overdrive itself is fine. I can't find the short but its got to be shorting somewhere...
View 14 RepliesFord Ranger / B-Series :: No Reverse Lights - Switch Location?
I've got a 2008 Ranger FX4, 4.0L with manual transmission. Recently I noticed that I have no reverse lights. I have to parallel park on busy streets from time to time, so this is a safety issue that I need to fix.
I checked the bulbs, both seem fine - would be unlikely that both bulbs would die simultaneously. I checked the fuse. Again unlikely unless the reverse lights were on their own independent circuit. 10A fuse looks fine too.
Last thing I can think of is a switch. I checked my Haynes Manual, there is no mention of it, which is odd, usually my manual is quite good. Where the switch is located? Any experience with swapping this out?
Ford Ranger / B-Series :: 1994 - Only Goes In Reverse When Warm?
I have a 1994 Ford Ranger XLT xcab with a 4.0 engine.It will take off and drive in the freezing cold but when it warms up it will only go in reverse.Once in awhile it will go into drive.What seems to be the problem. I had also backed up over a railroad tie in an icy parking lot but still drove away.
View 3 RepliesF Series :: 1999 - No Reverse / Forward Gear When Getting Out Of Park
My cousin has 1999 f-150 v8 automatic. Anytime you take it out of park you get forward gear. Was fine when parked just started happening on startup.
View 1 RepliesFord Ranger / B-Series :: Transmission Slipping / Won't Pull In Reverse
I'm having trouble with my auto tranny again. it is a 4r44e and is in a 1999 3.0 flex 2wd extended cab. It will not pull in reverse, seems to be slipping bad, and it won't pull in forward gears unless you switch OD off. Then it seems to pull fine but still not in reverse. I haven't drove it very much to see on changing gears and such for fear of burning it up.
Fluid is still like new no codes showing just started out of the blue while my son was driving. All electrical is hooked up tight and no leaks fluid is little overfull but not much. I am going outside now to adjust intermediate band to spec. had trouble with overdrive that had everybody stumped if you remember and it was overdrive band adjustment so going that route first.
Ford Ranger / B-Series :: 2000 - Won't Move Forward Or Reverse?
2000 ranger v6 automatic trans electronic 4wd shift on the dash. Plowing snow all of the sudden lost both forward and reverse never slipped or made any noise. Transmission fluid is fine to the level and clean. Put in drive nothing and reverse nothing put it back in park you can hear the park paul trying to click in. Towed it back to the shop thinking maybe the transfer case was junk. Decided to check the actuator on the transfer case no power going to it, go back to the switch no power there either check the fuses both are good and have power. The question i have is could a bad GEM module cause all this? ps the windshield wipers do work.
View 6 RepliesFord Ranger / B-Series :: Speedometer Will Reverse Despite Of Increasing Speed When Gets Over 75 MPH
1999 (built late 1998) Ranger 2.5 stick 2wd single cab. If I get much over 75 MPH the speedometer will reverse direction despite increasing speed. If I then let off the throttle completely, the speedo will jump right back up and indicate the correct speed. Continued operation without letting off the throttle to let the speedo recover will trip the ABS fault light, probably due to the erratic signal.
Disconnecting RABS module has no effect on symptoms. Speed sensor in the rear axle has been replaced already (by me) and the new unit ohm'd out good. Wiring between GEM and sensor checks out as well, good continuity (< 1 ohm) and no shorts to chassis ground. I wish I had an o'scope to take a look at the waveform, but I don't at the moment. It is on my future tool purchase list.
Ford Ranger / B-Series :: 2001 - Auto Trans Won't Drive / Reverse?
Daughter driving truck truck quits moving, I get there no drive and no reverse, has low and 2nd manually.
drive truck home, flush trans and cooler, road test all ok. this was 3 weeks ago.
This morning did it to here again, no drive and no reverse, she drove it home using manual low and 2nd.
I get in and when put into drive it feels like it tries but doesn't go all in, same with reverse. pulled it into low and vola I now have drive and reverse again
I'm thinking a we may have a bad or going bad shift solenoid. What I need to know is, is any of the solenoid valves on when in reverse are they the same as when in drive?
Ford Ranger / B-Series :: 1985 - Shifter Really Loose / Stuck In Reverse
1985 ranger 2.3L TK5 tranny. Shifter was really loose and the tranny finally got stuck in reverse. I have opened up the bottom cover, but am not sure where to move the shift forks to get it back to neutral. I bought a new shifter, but I need to get the tranny back to neutral before I can install it.
View 2 RepliesFord Ranger / B-Series :: New Clutch - Hard To Shift Going Into 1st / 2nd And Reverse Intermittently
1997 Ranger extended cab, 222k mi., 4 cyl, standard transmission. Shifting got worse until it finally died and the mechanic replaced the clutch "kit" and slave cylinder.
It still fights back going into 1st, 2nd, and reverse. But it is intermittent. If I put it in neutral, depress the clutch, and start the vehicle, then, after a few seconds wait, when I try to go into 1st (or reverse), it fights me back, forcing me to pause and apply about twice the pressure I should need to go into gear. When I go forward in 1st, and am ready to shift to 2nd, it fights back so that I have to pause just a bit and apply more pressure than I should for it to go into 2nd gear. 3rd, 4th, and overdrive are FINE. Also, the clutch seems to disengage about halfway down, where I was expecting it to disengage after only 10 -20% depression.
The mechanic doesn't see the problem (or won't admit it). Is there an adjustment to make the clutch disengage with only 10-20% depression instead of the 50%? Is that something I should be worrying about?
Is there some other problem? Like maybe the synchromesh mechanism in the transmission itself not bringing the transmission rotor to engine speed soon enough (wear on the synchromesh)?
When it was new, it went into ALL gears with ease, no fighting back, and it starrted doing this after about 150k miles. Now, at 222k mi., even with a new clutch, plate, throughout bearing, and slave cylinder, it still seems partially stuck going into 1st, 2nd, and reverse.
I just don't want to start replacing things until I can get a correct diagnosis as to what is causing the problem.
Ford Ranger / B-Series :: 2000 - Reverse Lost After Harsh Thud
I have a 2000 Ranger 3.0 4x4 with over drive. When backing out of my driveway there was a harsh "thud" (for lack of a better word) and I lost reverse. The forward gears are still working. We pushed it out on to the road and I drove to my place of business. At that time reverse worked again. It only lasted a couple more times. Still have the forward gears. Could it be a band or clutch?
View 9 RepliesFord Ranger / B-Series :: 1996 - Transmission Grinds When Putting It In Reverse
I own a 1996 XL Ford Ranger 2wd 5 speed manual.
Last week I had it in for some service, which included bleeding the clutch lines and new fluid.
Since then when putting it in reverse the transmission grids. It is also very difficult to get into first gear - I really have to shove hard on the stick.
Better Description of symptoms: When the vehicle is moving it shifts fine. When I come to a stop, put it in neutral and let out on the clutch, it is then very difficult to get back into first gear. If I leave the clutch in, fter I come to a stop, I can shift around to all the gears no problem. It's only when I let out on the clutch, then push it back in to shift into first is the difficult part.
With reverse, I have to move ahead a bit, THEN I can shift to reverse without the grinding noise. I talked to my mechanic who check to ensure the fluid was NOT low (it wasn't) and no air bubble existed in the line. After that was checked, he said the clutch is worn and has to be replaced.
Well, then, why wasn't it doing this BEFORE I had him bleed the lines? It started the day I picked the truck up from service. He recommends the following to fix the problem...
- slave cylinder
- new line
- disc
- preasure
I am asking why this would happen after he bleed the lines? Is there another problem that can cause this?
Ford Ranger / B-Series :: Reverse Gear Went Out - Transmission Repaired But No Power
The reverse gear went out in my 97 ford ranger with automatic transmission. I took the transmission out and replaced the reverse band, cleaned everything up, put it all back together and back in and filled it up with fluid. Unfortunately, between me and my assistant, we did not secure the pump correctly and sheared the ears off it. It made a racket when we started it. It would go through all gears while jacked up but when on the ground it had no power. It would barely move. And there was no fluid coming through the pump when I cracked the lines. We pulled it all out again, took it to a shop, put on a new pump and had them reassemble it all and we put it back in, making sure to do it right this time. But I still don't have the power I had before all this. It's very sluggish in all gears. There was no racket on start up this time. And when I crack the lines there is intermittent fluid loss but not a constant flow. I really don't want to pull this thing again. What am I doing wrong?
View 2 RepliesFord Ranger / B-Series :: 1996 Automatic Transmission Not Shifting - No Reverse / Drive Or OD
So here in Wisconsin for the last two weeks we have had nothing but ice. That being said, I have a '96 ranger 3.0L, automatic transmission, 4x4. 4 wheel is inoperable at the moment, that's a different story. Here's my question: with the ice, there has been a lot of tire spinning at high RPM's, the other day, I was again stuck on the ice and rocked back and forth had some pushers, thought we were getting somewhere but I went to shift gears and all of a sudden had nothing. No Reverse, Drive, OD, L, 2. Did I blow my tranny? There was no noise or grinding, but the OD light seems to blink. Is there something I can check or look at?
View 4 RepliesFord Ranger / B-Series :: 1988 Truck Will Not Pull In Reverse / Overdrive / Drive / Second Or First
I have a 1988 FORD Ranger with the 2.9 liter engine with the four speed automatic overdrive transmission. Several days ago the transmission went out. The truck will not pull in reverse, overdrive, drive, second or first. Usually most vehicles will usually have at least the reverse, A first or second when the drive and overdrive stops working altogether. What the problem could be?
View 1 RepliesFord 7.3L Power Stroke (1999-2003) :: Hold Gear Selector Towards Park To Get Reverse Lights To Come On
I have noticed that I have to hold my gear selector towards park to get the reverse lights to come on. Also some times I have to hold it towards park to get it to start. I changed my tranny in Dec 2009 and occasionally it would do this while starting, just noticed the reverse lights about a week ago. Tried moving the cable where it attaches to the tranny a couple of serrations each direction. No luck. Is there another place I can make an adjustment?
View 14 RepliesFord 6.0L Power Stroke Diesel :: 2005 - No Reverse Lights - Parking Sensor Stuck In Park?
Reverse lights not coming on, and parking sensor stuck at ' OFF ' , have replaced switch to no avail
Any tips out there ?
2005 6.0 Supercab Lariat diesel Auto 4 wd
Touareg :: Park Assist Show Just Red Lights When In Reverse
OK, each day my new T-Reg has a surprise. Today it was that the Park Assist showed just the red lights when in reverse. I know from the manual that this indicates a fault with the system.
I'm taking the car back to the dealer to have it diagnosed.... what should I expect? Is it as easy as hook up a computer and it says that sensor X is faulty??
Actually, the park assist seems to work when in 'D' so I assume that it's something on the back set that is faulty. The car is clean and only four days old from the dealer. I've checked the sensor exteriors and can't see anything covering them. Anything else I should check?