Ford Ranger / B-Series :: Transmission Slipping / Won't Pull In Reverse
I'm having trouble with my auto tranny again. it is a 4r44e and is in a 1999 3.0 flex 2wd extended cab. It will not pull in reverse, seems to be slipping bad, and it won't pull in forward gears unless you switch OD off. Then it seems to pull fine but still not in reverse. I haven't drove it very much to see on changing gears and such for fear of burning it up.
Fluid is still like new no codes showing just started out of the blue while my son was driving. All electrical is hooked up tight and no leaks fluid is little overfull but not much. I am going outside now to adjust intermediate band to spec. had trouble with overdrive that had everybody stumped if you remember and it was overdrive band adjustment so going that route first.
Ford Ranger / B-Series :: 1996 - Transmission Grinds When Putting It In Reverse
I own a 1996 XL Ford Ranger 2wd 5 speed manual.
Last week I had it in for some service, which included bleeding the clutch lines and new fluid.
Since then when putting it in reverse the transmission grids. It is also very difficult to get into first gear - I really have to shove hard on the stick.
Better Description of symptoms: When the vehicle is moving it shifts fine. When I come to a stop, put it in neutral and let out on the clutch, it is then very difficult to get back into first gear. If I leave the clutch in, fter I come to a stop, I can shift around to all the gears no problem. It's only when I let out on the clutch, then push it back in to shift into first is the difficult part.
With reverse, I have to move ahead a bit, THEN I can shift to reverse without the grinding noise. I talked to my mechanic who check to ensure the fluid was NOT low (it wasn't) and no air bubble existed in the line. After that was checked, he said the clutch is worn and has to be replaced.
Well, then, why wasn't it doing this BEFORE I had him bleed the lines? It started the day I picked the truck up from service. He recommends the following to fix the problem...
- slave cylinder
- new line
- disc
- preasure
I am asking why this would happen after he bleed the lines? Is there another problem that can cause this?
Ford Ranger / B-Series :: 1996 Automatic Transmission Not Shifting - No Reverse / Drive Or OD
So here in Wisconsin for the last two weeks we have had nothing but ice. That being said, I have a '96 ranger 3.0L, automatic transmission, 4x4. 4 wheel is inoperable at the moment, that's a different story. Here's my question: with the ice, there has been a lot of tire spinning at high RPM's, the other day, I was again stuck on the ice and rocked back and forth had some pushers, thought we were getting somewhere but I went to shift gears and all of a sudden had nothing. No Reverse, Drive, OD, L, 2. Did I blow my tranny? There was no noise or grinding, but the OD light seems to blink. Is there something I can check or look at?
View 4 RepliesFord Ranger / B-Series :: 1998 - Whining Sound In First Gear And Reverse That Varies According To Engine RPMs
I am looking over a 1998 Ford Ranger. Very low miles for its age (67,000) and kept in very good shape. When I took it for a drive, I noted an issue.
- there's a whining sound in first gear and reverse that varies according to the engine RPMs. I thought it might be the power steering pump, as that whined when I turned the wheel.
However, the noise went away when I shifted to the higher gears. Been a while since I drove a stick - my Bug back in 2003, IIRC.
What I might be getting into? I really like this machine, aside from that issue, and I would like to nail the problem down ASAP...
Ford Ranger / B-Series :: 1987 4x4 V6 Transmission Slips Out Of Gear
I have a 1987 ford ranger 4x4 2.9l v6 but my transmission slips out of gear and its auto im not sure why but ive been told im missing a over drive gear is this a possibility or what???
View 1 RepliesFord Ranger / B-Series :: 1997 - Transmission Not Shifting Down Into First Gear Not Even Manually
I just had a 97 Ford Ranger with a 3 speed overdrive transmission in my garage that we replaced the transmission because it was not shifting down into first gear, not even manually!. The new transmission is doing the exact same thing as the original.
View 5 RepliesFord Ranger / B-Series :: Transmission Adjustment / Rough Downshift Into 2nd Gear About 15 Or 16 Mph
My 93' Ranger XLT extra cab 2wd, 4.0 engine and A4LD auto tranny with 126,600 miles has a rough downshift into 2nd gear about 15 or 16 mph. Down shift to 1st is real smooth and upshifting thru the gears is smooth. I just put a new modulator valve on it and upshifts smooth out, they were getting to be hard shifts before changing that valve. I do not know if there is any adjustment that can be made to smooth out the rough downshift when slowing down to a stop for red light. The U-joins are in good shape and new carrier bearing assembly on driveshaft and no extra play in the rear end. A band adjustment maybe or just have to live with it.
View 5 RepliesFord Ranger / B-Series :: Transmission Abruptly Locked Up In Traffic In 5th Gear
1991 Ranger, standard cab, 2wd, 2.3L engine, 5 speed
Transmission abruptly locked up in traffic, in 5th gear, brought the truck to a halt. Got it towed home, searched the forum for information on how to remove the transmission, and tackled the task today. I've done transmissions and clutches before - how hard can this be?
Well, I've gotten everything loose and am ready to brace the trans and remove the cross brace to gain access to the top bolts - I have seen them, but haven't tried to reach them. I've been hung for about the last 3 hours trying to get the two top side bolts - heads facing forward. I can feel them, have gotten a socket on them, but have NOT been able to get a wrench up to them to break them loose. Feels like there is a reinforcing flange or something right adjacent that prevents access. I've tried extensions, flex joints and box ends - I just can't seem to find the right combination.
2nd question - do I need to break the exhaust system loose before I allow the engine/transmission assembly to tilt downwards? Looks to me like it needs to be disconnected to allow the assembly to drop.
Ford Ranger / B-Series :: Transmission Going To Upshift Then Immediately Downshift To The Gear It Just Left
1996' Ranger with 183,000 miles. 2.3 cyl., Automatic, XLT
When I am driving and get to the 35 to 60 mph range, my trucks transmission wants to upshift, then immediately downshift to the gear it just left. It goes back and forth like this till I get where I am going, or after about 10 miles it will stop doing it. I checked the transmission fluid, and it is full and still pink.
I took it to Advanced Auto, and it blew a code of ECL Bank 1 I believe. I looked around the 'net and I think it came out to be the front O2 sensor may be bad/going bad.
Last week while it was warm enough I was driving with the rear window open, and noticed the faint smell of Rotten Eggs (this has been the only time though). Today I drove about 50 miles and basically used a quarter of a tank of gas. I am wondering if the catalytic convertor may also be going bad?
Ford Ranger / B-Series :: 2000 / 4R44e Transmission - Hard Shift From 2 - 3 Gear
2000 Ranger 4R44e transmission.Hard shift from 2-3 gear and when i run about 35-40 mph and brake then acelerate it downshifts hard . Whats wrong with it?
View 14 RepliesFord Ranger / B-Series :: Loud Screech / Grind - Transmission Locked In 5th Gear
Last night, on my way home, I suffered a catastrophic transmission failure in my 1991 2.3L 5 speed. Stepped on the clutch on an exit ramp from the freeway and was rewarded by a LOUD screech/grind, a stopped vehicle, and a transmission "locked" in 5th gear. The local HERO service pushed me out of traffic and I got towed home. Looks like a transmission transplant is in my immediate future. So - the question is, what year manual transmissions match up to a 1991 2.3L 4 cylinder, standard cab, 2WD? I need to start searching salvage yards.
View 3 RepliesFord Ranger / B-Series :: 1986 - Transmission Overhaul - Hard To Get Clutch Into Gear From Neutral
Rebuild on the Mazda 5 speed transmission. My 1986 Ranger 2.3 Four cylinder has 280,000 miles and the clutch has never been replaced. It's not slipping but I'm having trouble getting it into gear from neutral. Was told that the release springs on the clutch plate have weakened causing the clutch to not release completely so figured it's time to replace it. It's done well the last 280,000 miles. The question I have : overhauling on one of these Mazda trans and how difficult was it. Any special tools required, etc...I see Autozone has a rebuild kit which appears to have bearings, seals and gaskets. Figured while it was out I would go ahead and rebuild it myself if I can. Rebuilt a few engines but never touched a trans.
View 4 RepliesFord Ranger / B-Series :: Reverse Lights Only Come On Between Park And Reverse
On my '96 ranger with an automatic the reverse lights only come on between park and reverse, but once put into reverse they go out. The gear selector on the dash reads right, when the needle is on"P"it's in park, "R" drops into reverse and so forth. Do I need to adjust the shifter cable on the side of the transmission? If so how do I do this (I kinda need step by step with removal and adjusting, I've already tried and couldn't get it off the bracket). It's starting to drive me nuts, I've searched on the web for hours with no luck. I've even posted on other sites with zero answers.
View 7 RepliesFord Ranger / B-Series :: 1994 - 3.08 Gear Swap To 3.55 Effect Power?
Im wanting to get more power out of my 94 auto supercab but I don't wanna kill mpg it has 3.08 gears I was thinking swap to 3.55 to keep mpg would there be noticeable power difference?
View 6 RepliesFord Ranger / B-Series :: Hard To Get Out Of 2nd Gear / Engine Surges Then Starts To Lose Power
My surging/running down issue has returned on my '86 2.3l Ranger. I thought it was electrical, when things improved with the new ignition switch, but lately it's hard to get out of 2nd gear before the engine surges then starts to lose power. a poke of the gas pedal starts the who cycle over again. I pulled codes but it's hard to tell what the reader is saying either 33 and 34 or 334. The good thing is all the codes point to the EGR system. Looking for a diagnosis tree to determine if the valve is bad or the sensor is shot? They are both not cheap so I don't want to just throw parts at the problem.
View 14 RepliesFord Ranger / B-Series :: 1998 - 4r44e Transmission - Randomly Losing Power While Driving Like It Would Not Shift
Ok I've got this 98 Ranger with the 2.5L and the 4r44e automatic. The engine is used and has about 100,000 miles now and is it a good state of tune - so I think. The transmission was a remanufactured I bought a few years ago that was built with the shift improver kit, Kevlar bands, extra planetaries, 4wd pan, and external cooler. It's now got 92,000 miles on it and it's been serviced every 30,000 with a fresh 4wd filter and Mercon V fluid. It's outlasted the last 3 transmission I've had in my Ranger. I've got 315,000 miles on the body. For awhile it was randomly losing power while driving like it wouldn't shift, almost like it dropped a couple cylinders, then as you kept your foot on the gas it would recover and rev up and shift.
Then sometimes randomly at stoplights it would shake at a stop and have no power at take off until it hits 30-40 mph. Sounds like a converter, is what I thought. But now it's doing it more often but not the shaking at stoplights as much as randomly losing power while driving normal speeds. Last night I drove it about 50 miles after doing a fresh filter and fluid change and this time it did it so much it threw a code up P1131. Even though that's a O2 sensor code, could it be hidden by a transmission valve body problem? One transmission shop said it could be a valve hanging up just by me describing it to him. Could this be ignition or fuel related or is it all tied in with the transmission problem, if it is even a transmission problem?
Ford Ranger / B-Series :: 1993 - Power Steering Or Gear Box / Return Hose Leaking Where Rubber Meets The Crimp
Either one of my power steering hoses or the gear box is leaking on my 93 Ranger. It appeared the return hose was leaking where the rubber meets the crimp. So I decided I would go ahead and change the return and pressure hose to see if it stops the leak. It was a disaster. It's 2.3L manual transmission 4x2. I got the return hose off ok. I put the wrong size wrench on the pressure hose fitting at the pump but thought it was loosening but it was rounding the nut off. So I couldn't even change that hose. I installed the new return hose and retightened the pressure hose at the gear box.
Well it was a pain getting the flare fittings of the hoses into the steering box so I could tightened the flare nut down. I finally got them tightened, I think, but then when I started the engine fluid shot out of there like a water hose. It's coming from the fittings at the gear box that I thought were tightened. I reloosened and retightened them again and still it's shooting out everywhere. There is so little room getting a wrench on the hose fittings, it was slow going. What do you need to remove in order to get a good straight shot and installing these flare nut fittings and tightening them down right? If I remove the pump will it be easier to install the hoses on the gear box? I have to remove the pump now to change the pressure hose.
Ford Super Duty (1999-2016) :: Losing Power In Reverse / Transmission Not Always Going Into Last Gear On Interstate - Code PO741
I have been having trouble with my 2008 Ford F250 4x4, 6.4 liter diesel transmission. SCT tuner, 10" lift, egg delete and dp delete has been done. I have been losing power mainly in reverse but have noticed that the transmission hasn't always been going into the last gear on the interstate. Code PO741 would come up. The other day the shifter was stuck. So I played with it and found that the cable on the transmission had fallen off. After replacing it. The transmission wouldn't go into reverse but has been doing semi good in forward. Well I have been limping it around until today when I was going down the road and it completely stopped pulling. Now no matter what gear I place it in, it will on go in reverse. What could be causing these issues or where to even begin to start looking?
View 3 RepliesFord Ranger / B-Series :: Gear Shifter Does Not Go Into 1st Gear But Changes To Other Ones
I bought a 96 Ford Ranger XLT Supercab 4.0 on the 21st and the gear shifter doesn't go into 1st gear but changes to the other ones(see pic below) and was wondering if it's a easy fix.
Also I have a oil drip(at least it looks like oil to me) and I can't figure out where it's coming from because it's a small drip and the oil dipstick and tranny dipstick both show full and I can't figure out where the drip is coming from and I only noticed a dip on a metallic tank but don't know what that is either but check out the pic below to see the drip I circled.