Ford Ranger / B-Series :: 1988 - Missing / Stumbling Especially At About 55 MPH While In Overdrive
I've got a 1988 2wd Ranger with a 2.9l v6. I just recently got it running. It has been setting for awhile. I replaced fuel tank, both pumps, fuel filter, Plugs, Wires, Cap, Rotor, TPS. It ran great for about 100 miles. Then yesterday on my way to work about 4 miles down the road it started to miss/stumble especially at about 55mph while in overdrive. When I got home I pulled the codes and I got KOEO 22 Map sensor signal out of voltage(engine off), 53 TPS signal voltage to high, 95 Thermactor Air System Problem, or Fuel Pump Monitor signal, indicates circuit problem.
KOER I got 21 ECT sensor signal voltage out of range or loss of signal during normal operation or Crank Sensor problem, doesn't have a crank sensor I believe. But I did change the ECT sensor and it still stumbles and seems like it misses. Noticed it is sluggish getting up to speed kinda surges and bogs. Im at a loss it isn't showing any more codes. Checked all plug wire connections and made sure everything was making connection. The only other thing I can think of is that the ignition module on back of distributor is going bad. Not advancing the time correctly.
Ford Ranger / B-Series :: Transmission Slipping / Won't Pull In Reverse
I'm having trouble with my auto tranny again. it is a 4r44e and is in a 1999 3.0 flex 2wd extended cab. It will not pull in reverse, seems to be slipping bad, and it won't pull in forward gears unless you switch OD off. Then it seems to pull fine but still not in reverse. I haven't drove it very much to see on changing gears and such for fear of burning it up.
Fluid is still like new no codes showing just started out of the blue while my son was driving. All electrical is hooked up tight and no leaks fluid is little overfull but not much. I am going outside now to adjust intermediate band to spec. had trouble with overdrive that had everybody stumped if you remember and it was overdrive band adjustment so going that route first.
Ford Ranger / B-Series :: 1988 - Transmission Fluid Leaking Badly / Truck Barely Moves
1988 ranger, its a automatic 4x4 v6 and is leaking tranny fluid real bad. Truck barley moves because fluid comes straight out...
View 1 RepliesFord Ranger / B-Series :: 2001 - Auto Trans Won't Drive / Reverse?
Daughter driving truck truck quits moving, I get there no drive and no reverse, has low and 2nd manually.
drive truck home, flush trans and cooler, road test all ok. this was 3 weeks ago.
This morning did it to here again, no drive and no reverse, she drove it home using manual low and 2nd.
I get in and when put into drive it feels like it tries but doesn't go all in, same with reverse. pulled it into low and vola I now have drive and reverse again
I'm thinking a we may have a bad or going bad shift solenoid. What I need to know is, is any of the solenoid valves on when in reverse are they the same as when in drive?
Ford Ranger / B-Series :: 1996 Automatic Transmission Not Shifting - No Reverse / Drive Or OD
So here in Wisconsin for the last two weeks we have had nothing but ice. That being said, I have a '96 ranger 3.0L, automatic transmission, 4x4. 4 wheel is inoperable at the moment, that's a different story. Here's my question: with the ice, there has been a lot of tire spinning at high RPM's, the other day, I was again stuck on the ice and rocked back and forth had some pushers, thought we were getting somewhere but I went to shift gears and all of a sudden had nothing. No Reverse, Drive, OD, L, 2. Did I blow my tranny? There was no noise or grinding, but the OD light seems to blink. Is there something I can check or look at?
View 4 RepliesFord Ranger / B-Series :: Transmission Locked Out - Truck Would Not Move When Put In Drive
Last night I backed up out of a parking space and when I put it in drive it wouldn't move. It seemed like the transmission was locked up. What happened? The truck was running fine. It's a 2002 Ford Ranger 3.0 with auto transmission. Getting it serviced? I'm tempted to go to a dealer. What the problem is? Repair costs? The fluid looks good - no burning smell.
View 5 RepliesFord Ranger / B-Series :: 1997 - Truck Will Rev Up And Down From 500 - 1000 RPM When Rolling In Drive
I have a 97 Ranger 4x4, 4.0L, A4LD, 68k mi. with P0171 and P0174 codes, lean fuel mixture banks 1 and 2. The truck will rev up and down from 500-1000 RPM when Im rolling in Drive. When I accelerate, its fine, but when I let off the gas and roll it starts revving again causing the truck to shake. I replaced plugs and wires before the codes (1-2 months ago). After the codes came I replaced the fuel filler neck (not because of the codes), cleaned the air filter, cleaned MAF, changed fuel filter, and checked fuel pressure which was at 29psi so I replaced the fuel pump. Is there any common causes for this? Cures?
View 14 RepliesFord Ranger / B-Series :: 1999 Truck Has A Delay When Put Into Drive Sometimes It Slips At Takeoff
I have a 1999 ranger 3.0 4x4 automatic the truck has a delay when put into drive sometimes it slips at take off unless I force it to downshift and stay in first and from second to third gear it shifts very hard at around 3500 rpm would an oil and filter change. I do not have the cash for a new trans and I can't afford a new truck. I love my little ranger...
View 10 RepliesFord Super Duty (1999-2016) :: Truck Will Only Go In Reverse / Can't Even Pull It Forward
Have 2001 F-250 7.3 PSD, automatic, ESOF (had to replace the original hubs with Warns)have kept up the maintenance,oil, grease, ATF fluid & filter, truck has been virtually trouble free. About 2 weeks ago I decided to go across an area of the lawn, as I was going (in 2 wheel drive)I felt the tires spin a little so I stopped got out and locked the hubs, got back in truck turned t-case to 4 high. had to rock the truck out of a damp area but nothing really.
So I got back to where I came in at (in reverse about 100') stopped put it back in 2 wheel drive, tried to go forward, very difficult, sluggish, got back in driveway had to back the truck in, will not go forward at all now. Checked all fuses, rapped the the t-case motor, no codes. So I thought I'd move the ruck, have a winch that will pull it out by the barn, I could not even move the truck forward by pulling it with a winch. As I said have never had any problems with truck. Transmission fluid is good, clean no burnt smell.
Ford - Ranger :: 2004 - Truck Does Not Pull To One Side Or The Other While Driving
i have a 2WD 2004 Ford Ranger regular cab. I have replaced the rotors three times in the last year due to warpage. What is causing this? The truck does not pull to one side or the other while driving. applying the brakes don't cause it to pull to one side either. According to my mechanics, neither caliper is sticking. the right brake pad does show some signs of heat damage (cracking). There is no uneven tire wear. I have a buddy who thinks it may be a bent wheel hub, but my mechanic says no because no uneven tire wear. They are leaning to a faulty brake hose, but can't say for sure.
View 3 RepliesFord - Ranger :: Overdrive Light Flashing Usually When Drive On The Highway
My 98 ford ranger overdrive light starts flashing usually when I drive on the highway. When I get off the highway and drive in town with o/d light flashing the truck downshifts hard when slowing down at stoplights.,also when almost to stop i hear ticking sound in tranny until i come to complete stop. My ranger is 4wd 4.0 and automatic.
View 2 RepliesFord Ranger / B-Series :: 1999 Won't Go Into Overdrive
I went to transmission shop today and tech told me c solenoid was showing performance problem when scanned. He took it for drive and said it was commanding shift into fifth gear. It is a 3.0 extended cab 2wd with just over 200000 on truck, transmission was rebuilt just over 25000 miles ago. Fluid is so clean its still clear looking just faint red color. All other gears shift and pull great all electrical clean and hooked up, he crawled under it and said pan adjustments were tight, whatever that means.
View 14 RepliesFord Ranger / B-Series :: 1988 - Headlights Won't Turn On At All?
I have a 1988 ford ranger and my headlights won't turn on all my fuses are fine but no headlights! All the other lights work fine blinkers, parking, brake ,and tail lights! What do I need to look for????
View 14 RepliesFord Ranger / B-Series :: 1988 - Overheats While Idling?
My 88 2.9 ranger keeps heating up badly while idling. Was waiting in the drive-thru at Wendy's and it was taking them longer than usual, the temp guage started climbing closer and closer to 'H'.. I revved it up a bit to a fast idle (1500-2000rpm) and it did not work much... figured the gauge was being screwy. But when i finally got my food and started moving the truck was pinging..it really was hot..
But as soon as I got her moving at a steady 40mph, engine cooled back down to normal temp as if nothing ever happened..i put an extra wide two row aluminum radiator from a 4.0 explorer in it, fan clutch is not very old, no coolant leaks that i can see.. can't figure out why it heats up so much so fast at idle. Not enough air or coolant flow?
Ford Ranger / B-Series :: 1988 - Won't Start - No Spark
Any way to tell if the ECU is faulty? I hooked my analyzer up to my friends 1988 Ford ranger 2.3L and it wouldn't even detect that the ignition switch was on. He was driving it the other day and is shut off on him while he was making a turn and it wouldn't start back up. We have rebuilt the distributor by replacing the pick-up, rotor button and cap, and we had the ignition module tested and found it was good. We have also replaced the coil. When the ignition is turned to the on position, the fuel pump comes on and never cycles off.
View 8 RepliesFord Ranger / B-Series :: 1988 - Won't Idle - Starts Right Away Then Die?
88 ranger. 2.9L manual. Just bought this truck. It ran great when I bought it. After a day or 2 it would idle rough. Almost die but it wouldn't. No check engine light. It seemed to do this intermittently. Some times I'd start it and it be fine. Other times I'd start it and I'd expect it to die at each stop light.
Now for the last couple days it dies on every start up. It won't idle. It'll start right away and then die. I can keep it going by keeping the engine rev'd but the check engine light is one. If I keep it running and start driving down the road it'll drive with the check engine light on for about 5 minutes. Then the light goes out and it runs like normal, even at idle, until I shut it off. Then it's the same story at next start whether it's right after I shut it off or hours later.
It doesn't seem to matter whether the engine is hot or cold. When the check engine light is out, it runs great the rest of the time whether at speed or at idle. To me it sounds like a sensor is on it way out. I figure if it was vacuum, it happen at every idle, and if it was fuel it happen all the time or at least every idle. Tried to get a code at parts store but the reader wouldn't work. It couldn't tell it was plugged in the the truck for some reason.
Ford Ranger / B-Series :: 1988 XLT V6 Won't Start Just Crank
I have tried about everything i know about cars on this truck!! It ran great when I got it until a head gasket got blown so I tore into it and replaced them both torqued heads to specs. Made sure valves wasn't to tight. Distributor is in correct spot timing is correct had ignition module tested good!!! Coil tested good replaced both fuel pumps and put new tank and sending unit in the truck b/c it needed it new fuel filter replaced return line firing order is correct 1 4 2 5 3 6 it is getting fire it will crank and crank sometimes act like it is going to start then not also I can get it to run for about 3 sec on 3 or 2 cylinders it seems to have plenty of compression as well!! only thing really I can think of that could be wrong is computer? Also one last detail tried pull starting it as well still wouldn't go.... V6 2.9L...
View 9 RepliesFord Ranger / B-Series :: 1988 - How To Tightened The Valve
It's an 88 2.9 and sounds like a little diesel! The fellow I purchased it from said the valves need tightened, I thought perhaps a timing chain, but figured valves would be an easier place to start. Yet, I'm not sure where to begin? Or how tight the valves need to be, are there torque specks?
View 2 RepliesFord Ranger / B-Series :: 1988 - Turn Signals Not Working
I have an 88 ranger with the 2.9l. The headlights work and the markers do to. The brights don't though. and also none of the turn signals work, the brake lights work though but i don't think the reverse do, I can't see them. Do the turn signals and brights share a fuse on there own? How to diagnose it or what it may be?
View 9 Replies