Ford Ranger / B-Series :: 2001 4.0 SOHV Upper Intake Manifold Removal
It doesn't look anything like the illistration in my Haynes book.Where are the bolts located and how many?
View 14 RepliesFord Ranger / B-Series :: 2003 - Intake Manifold Leaking?
'03 Ranger, 2.3L. Runs great except at idle. Code p0171. Replaced IAC, no luck.
Brake cleaner leak test definitely results in engine rpm change right around "butterfly rod" plug in front of intake manifold near no. 1 cyl. I'm pretty sure that's the problem - the plastic plug blew out. I watched a video showing repair, but it seems lacking.
I do not want to loosen up intake for access - I'd rather remove steering pump and gain some access to plug it up. There still isn't much access but, but eyeballing it, enough to plug, I think.
Three steering pump bolts came out easy. The fourth one is behind fluid line - extremely difficult to access, imo.
Somehow try to remove pump for access to intake hole, or bite the bullet and remove intake manifold for access?
Ford Ranger / B-Series :: 1987 V6 - Intake Manifold Removal?
I was working on my friend's '87 Ranger with 2.9 L V6, and a little bit of dirt fell into the intake manifold through the injector ports and intake ports. I should've cleaned the top of the engine with a shop vac first. Anyway, should I remove the intake manifold, or try to vacuum the bits out? It's pretty oily inside, and they might be stuck to the inside of it, so the vac might not do much. If I have to remove it, do I have to de-mesh the distributor gear to remove it, or does the distributor attach to a splined shaft? After looking at the diagrams, the answer was unclear.
View 1 RepliesFord Ranger / B-Series :: Antifreeze Leak - Tightening Intake Manifold Fasteners
I am mixed up in which fasteners I have to tighten to stop my antifreeze leak. For this, I got some pictures. Do I have to tighten these bolts? Or these? Is this the upper intake intake manifold?
I am just really lost and want to tighten the right bolts and find the torquing specs of the bolts. In the first picture, we can clearly see there is a leak there of what must be antifreeze. The stuff I have been loosing slowly over months.
Ford Ranger / B-Series :: 1996 4.0 - Loud Whistle Intermittently From Intake Manifold Area
Just bought this truck and no check engine light was on, went to get it smogged so I could register it and it had the following fault codes: P1443, P0401, P1131, and P1132. The truck seems to run great in my opinion and even gets really good gas mileage. There is a whistle intermittently from the intake manifold area though that is at times pretty loud.
Smog tech told me these trucks are "notorious" for the check engine light going bad and that usually the entire instrument cluster has to be replaced in order to fix it. I'm a very experienced motorcycle /small engine tech but do not have much experience with car/truck engines and especially not with emissions control systems.
Again it is a 1996 Ford Ranger 4.0 V6, 4 wheel drive STX with 185,000 miles on it. Where to start or what might be the source(s) of these error codes?
Ford Ranger / B-Series :: 1994 - Sputtering Started Suddenly - Vacuum Leak Behind The Intake Manifold
I have a 94 ranger and all of a sudden it started sputtering, i can hear a vacuum leak behind the intake manifold found what appears to be a pcv valve not hooked up is that the way it's supposed to be?
View 2 RepliesFord :: Escape - Coolant Spilled On Upper Intake Manifold / White Smoke On Startup
Coolant spilled on my upper intake manifold. I washed it off to the best of my ability but when i started the car white smoke came from tge exhaust. What my next move should be?
View 3 RepliesFord Super Duty (1999-2016) :: F250 - Hole At The Back Of Upper Intake Manifold
1999 F-250 LD 5.4... There is a hole on the back of the upper intake manifold, just below the back of the throttle body, is a vacuum hose supposed to be attached here? Have a serious vacuum leak, no coolant loss, no overheating, just had cop's and spark plugs done, now she backfires, stalls and will not stay running, mech. says its an intake gasket but the gasket and lower intake manifold look new.
View 7 RepliesBonneville :: 1995 Pontiac GM 3.8 Upper Intake Manifold Replacement
Just today,when replacing the UIM on a naturally aspirated 95 Pontiac Bonneville 3.8 with a Dorman upgraded type from my local auto parts, I ran into an issue. When following specified torquing sequences and specs , be very careful with the 1 long stud (#7), as it will split your new manifold there if you try to torque to 89 in/lbs. Took 1st back for replacement ,and the second new one started to split at the same place. Was using a brand new Craftsman in/lb torque wrench set correctly and following instructions exactly. I've seen a lot of excellent info on this UIM issue with the GM 3.8 ltr 1995-2004 years, but never this issue with the replacement ones. If I have to change this again will definitely go with the aluminum one.
View 1 RepliesFord Ranger / B-Series :: 2011 - Oil Leak On Upper Right Front Of Motor
I saw a nice very clean 2011 ranger with 63,000 miles on it . But there looks like it has a oil leak on the upper right front of the motor. Behind the pulley that does not have any groves in it . It could be a gasket or a oil seal I don't know. Is this oil leak something common with the 2.3 engine?
View 4 RepliesFord Ranger / B-Series :: 1998 - Torquing Upper Shock Mounting Nut
I replaced the front shock absorbers on my Ranger today and I have a question about torquing the upper mounting nut. The problem I have is that the threaded rod that is attached to the top of the shock turns when I put a socket on there and try to torque it to the proper spec. You can put a crescent wrench on the top of that threaded rod(it has flat spots) and tighten the nut some with a wrench, but the crescent wrench wants to slip and round off the top of that threaded rod. So my question is, how do you torque that upper nut without the shock spinning below?
It's a '98 2.5 ltr., 2 wheel drive with coil springs.
Ford Ranger / B-Series :: 1992 V6 - Upper Radiator Hose Gets Sucked Flat When RPM Is Higher
1992 3.0L V-6 RANGER
New thermostat
New Water Pump
I noticed the other day that the Upper radiator hose gets Sucked Flat when RPM is higher than Idle BAD it completely collapses IDK how it can circulate the coolant very well in this Condition. If the hoses have ever been changed But the Upper hose Really gets sucked flat. I've seen this a few times on vehicles that have been shutdown But they have always expanded upon startup and are fine....
The Lower Looks Fairly Old and only partly collapses under higher RPM.... I am going to change the Upper hose at a Minimum as its really Bad and probably a lot older than I am thinking and really Soft. I am just wondering if the radiator could be plugged up causing some of this.. Or anything else I should check into????
Ford Ranger / B-Series :: 1999 XLT - Rear Door Locked From Upper Side / Lower Looks Free
I have a 1999 XLT and i had a bad moment yesterday. I always put the toolbox in the back side of the cabin, while doing maintenance i tried to open the rear door and I couldn't. I noticed its locked from the upper because the lower looks free. The other thing i noticed the two wires going to the handle to open it feels loose. First time happened to me and i really use that door often.
View 2 RepliesFord Ranger / B-Series :: Broken Bolt At Downpipe On Exhaust Manifold
This is for a Pontiac Vibe. I broke one of the bolts that connects the exhaust pipe to the exhaust manifold. Need to get some type of nut/bolt/spring that I could use to fix it. The bolt is sticking out of the flange about 3/4" if I had a long nut to screw onto that?...........
View 6 RepliesFord Ranger / B-Series :: 2011 - Installing Cold Air Intake?
I would like to install a cold air intake in my 2011 Ford Ranger. What brand should I go for? Volant or K&N?
View 4 RepliesFord Ranger / B-Series :: 2002 - Popping Sound Coming From Intake Air Filter?
My 2002 2.8 diesel ranger has recently been serviced replacing the turbo and a complete overhaul on the engine performed. I road tested it and it runs smooth... However, I am hearing a popping sound coming from the intake air filter. I was told it is because of the new turbo installed.
View 2 RepliesFord Ranger / B-Series :: 1987 - Antifreeze Leaking At The Rear Of Engine Where Intake Attaches To The Block
Son has a 1987 ford ranger 2.9 engine 5 speed 4x4 truck. See anti freeze leaking @ the rear of the engine where the intake attaches to the block. How long to re & re the intake, ect. Is it just gaskets or what? Is it a big job?
View 9 RepliesFord Ranger / B-Series :: 2001 - Driver Side Power Window Motor Won't Stop After Window In Upper Position?
2001 Ranger 4 liter 4 door My driver side window goes up and the electric motor does not stop running when the window reaches its normal upper position. Instead it goes bang-bang-bang until I take my finger off of the switch. I'm guessing there is a limit switch that should disconnect the motor but has failed. The bang-bang (again I'm guessing) probably is some sort of a spring loaded torque limiter to protect the motor. Other than that, the window goes up & down as it normally should. I have no problem digging into the door, except with the window, door lock and outside mirror switches, I don't have a clue regarding how to get the inside door panel off. I know to disconnect the battery 1st.
View 1 RepliesExplorer :: 1999 Ford 4.0L - Removing Upper Intake
I went thru a 100 posts on "Intake gasket" search but I couldn't find any repair information on the 4.0L intake gasket replacement. I'm having difficulty pulling the upper intake off. All nuts and connections have been removed except for the egr tube that's connected to the upper intake.
According to another site, u should be able to just pull straight up, clear the intake studs, turn the intake to the left and then up due to the fact the egr tube is curves inside the intake towards the front of the upper intake. No luck. egr tube won't separate from the intake. This is a little long but everything has been disassembled to this point. BTW this is a 4.0L OHV engine