Ford Ranger / B-Series :: 2001 - Driver Side Power Window Motor Won't Stop After Window In Upper Position?
2001 Ranger 4 liter 4 door My driver side window goes up and the electric motor does not stop running when the window reaches its normal upper position. Instead it goes bang-bang-bang until I take my finger off of the switch. I'm guessing there is a limit switch that should disconnect the motor but has failed. The bang-bang (again I'm guessing) probably is some sort of a spring loaded torque limiter to protect the motor. Other than that, the window goes up & down as it normally should. I have no problem digging into the door, except with the window, door lock and outside mirror switches, I don't have a clue regarding how to get the inside door panel off. I know to disconnect the battery 1st.
View 1 RepliesFord Ranger / B-Series :: PS Leak And Pump Goes Empty When Steering With Motor Off
My truck lost its exhaust a few months ago and it's on the back list of things for this truck so I've been running it without it. However, my neighbors do not like it so, I frequently shut the truck off and coast in down my driveway to park it when it's late. But anytime I do that, I will park the truck and notice a puddle of ATF(ps) on the ground and the PS pump goes empty. Nearly no loss for a weeks when I don't turn the wheel with the motor off.
View 2 RepliesFord Ranger / B-Series :: 1998 - Gas Leak / Smell Whenever Start The Motor
My ranger decided to start leaking fuel somewhere probably a few weeks ago. I can smell it whenever I start the motor, and sometimes while driving with the windows down. Last night, I finally looked into the problem. I took the intake air hose off. The hose, air filter, and whole intake smells like gas. I'm thinking that shouldn't be the case on a fuel injected engine. After seeing some people talk about the Fuel Pressure Regulator go bad, I pulled the vacuum line off of it, and it has a very strong gas smell. I don't see any gas coming out of it, though, even with the motor running. Everything I read says if the regulator is bad, then gas should come out of the vacuum line. Is there another check I can do on it to confirm this is the problem? Is there somewhere else I should be looking? It got two new heads right before this problem started, so its quite possible I knocked something putting it back together.
View 6 RepliesFord Ranger / B-Series :: 1997 - Oil Leak Near Front Engine?
I have a 1997 4.0L Ranger with an oil leak. It is near the front of the engine, I don't really see where it is. I was wondering if there is any common oil leaks near that general area?
View 4 RepliesFord Ranger / B-Series :: 1996 - Oil Leak Coming Off The Front Of Engine
Changed my oil today. Noticed oil coming off the front of the engine. Where this could be originating or do I need to take the belt cover off? I hate having a leak. Wanna get it to stop. Just need to know what I may be up against. 1996 2.3ltr.....
View 9 RepliesFord Ranger / B-Series :: Warmed Up While Driving - Fluid Leak From Front Of Transmission
I bought a 1990 ranger with only 38000 miles on it from a online auction from boing aircraft. it never left the flight line and never even had a title. I picked it up from the airport and found out that it didn't have AC like they said, I was a little ticked but that isn't the main problem. When I drive it and it gets warmed up it leaks Tranny fluid from the front of the transmission. The engine does not overheat. It is a 4 cyl AOD automatic with a real thin radiator and a transmission cooler. Without AC the truck isn't the good deal I thought I was getting, and with a bad tranny this is becoming a big OOPS. Why this is happening?
View 3 RepliesFord Ranger / B-Series :: 1998 - Torquing Upper Shock Mounting Nut
I replaced the front shock absorbers on my Ranger today and I have a question about torquing the upper mounting nut. The problem I have is that the threaded rod that is attached to the top of the shock turns when I put a socket on there and try to torque it to the proper spec. You can put a crescent wrench on the top of that threaded rod(it has flat spots) and tighten the nut some with a wrench, but the crescent wrench wants to slip and round off the top of that threaded rod. So my question is, how do you torque that upper nut without the shock spinning below?
It's a '98 2.5 ltr., 2 wheel drive with coil springs.
Ford Ranger / B-Series :: Polishing And Porting Upper Intake Manifold
So i was thinking about buying a intake manifold for my truck and porting it and polish it. Would it be worth doing. I've decided that trying to port the heads will take up to much time and money for gaskets. Now the only reason why I am buying another stock one is so i can take my time and do it right.
View 14 RepliesFord Ranger / B-Series :: 2001 4.0 SOHV Upper Intake Manifold Removal
It doesn't look anything like the illistration in my Haynes book.Where are the bolts located and how many?
View 14 RepliesFord Ranger / B-Series :: 1992 V6 - Upper Radiator Hose Gets Sucked Flat When RPM Is Higher
1992 3.0L V-6 RANGER
New thermostat
New Water Pump
I noticed the other day that the Upper radiator hose gets Sucked Flat when RPM is higher than Idle BAD it completely collapses IDK how it can circulate the coolant very well in this Condition. If the hoses have ever been changed But the Upper hose Really gets sucked flat. I've seen this a few times on vehicles that have been shutdown But they have always expanded upon startup and are fine....
The Lower Looks Fairly Old and only partly collapses under higher RPM.... I am going to change the Upper hose at a Minimum as its really Bad and probably a lot older than I am thinking and really Soft. I am just wondering if the radiator could be plugged up causing some of this.. Or anything else I should check into????
Ford Ranger / B-Series :: 1999 XLT - Rear Door Locked From Upper Side / Lower Looks Free
I have a 1999 XLT and i had a bad moment yesterday. I always put the toolbox in the back side of the cabin, while doing maintenance i tried to open the rear door and I couldn't. I noticed its locked from the upper because the lower looks free. The other thing i noticed the two wires going to the handle to open it feels loose. First time happened to me and i really use that door often.
View 2 RepliesFord Ranger / B-Series :: Dies / Won't Restart - Motor Stumble Every So Often
My MILaw Truck 1992 ranger isnt running good and I need to get it going
Only a P0111 at this time IIRC
We started the truck tonight and idel ok Could see the motor Stumble every so often. She went to drive it and it Cuts out under Load Or you must rev it up to keep it from Stalling.
And if it does Cut out you have to let it sit for 5 minutes to restart what is Weird is it dont Smell Flooded either I smelled the VAC Line to the FPR and it was DRY and Did NOT Smell like Fuel.
It was dark didnt do much trouble shoot as the Flashlight died. I wonder about Fuel Filters. And Also about the Idel Control. The Mis or Stumble seams Random
Any testing I can do I have a DVM and that Code Reader. Might have to find something to check fuel press with where would I check it at the fuel rail I assume. Going to try and go over the Basics tomorrow If there is Anything Specific I should check?
Ford Ranger / B-Series :: 1993 - Wiper Motor Removal?
How do you remove this clip holding the wiper linkage to the back of the motor? I can't see what kind of clip it is to know how to remove it. Ford says to remove the wiper pivot and let it drop. Is that necessary? I can't barely get to the back of the motor so I'm having to feel the clip and remove it but since I don't even know what kind of clip it is it makes it so much harder. Does the cowl cover not come off or is it just this access panel?
View 3 RepliesFord Ranger / B-Series :: 1996 - Motor Seems To Stumble When Going Through Gears
1996 Ranger 2.3. I bought it from a friend 2 months ago. 228,866 miles. The motor seems to stumble as I'm going through the gears. I've cleaned the mass air flow sensor and installed new air filter. Check engine light has always been on, O'Reillys hooked up their computer to it and said Emission Valve Malfunction. I see the charcoal canister, then I have 2 electrical sensors on same line. First one from canister looks like what Rockauto.com shows as a Vapor Canister Purge Valve. The photo has it with a yellow orangeish top. I don't know what this 2nd sensor is. It has a blue top.
View 2 RepliesFord Ranger / B-Series :: 2005 - ABS Motor Humming When Grabs
I just changed my front brakes in my 05 Ranger. New rotors, pads, bearings (packed), racers, new caliper on driver side, bleed all for brakes. Now when I am just about to stop it feels like the left front is grabbing. I also hear the ABS motor humming when it grabbs. Don't whats causing it?
View 4 RepliesFord Ranger / B-Series :: Motor Swap From 1994 To 1987 Model?
I have a 1987 ford ranger, it has a 2.0L carborated motor and I also have a 1994 ford ranger fuel injected motor I believe it's a 2.3L, I am wondering if the swap will work to put the 94 motor in the 87....
View 3 RepliesFord Ranger / B-Series :: 1997 - Blend Door Motor Removal?
My actuator/motor doesn't have the screws that hold it on. It's just clipped down. Can I just pry it up & off with out it breaking the clips that hold it down? It's a 97 Ranger.
View 2 RepliesFord Ranger / B-Series :: No Movement From Starter Motor When Key Is Turned To Start
I have a 2002 Ford Ranger with a 3.0L engine that is having some issues with starting, here is what is happening.
Every so so often when the key is turned to start there is no movement from the starter motor. The battery is fine and all of the dash lights stay on while the engine is not starting. I have replaced the starter with a remanufactured model (possibly a mistake), and also replaced the clutch interlock switch.
I have attempted to change the ignition switch but the replacement I received did not even try to turn the starter (after many tries), like possibly it was faulty out of the box. I am currently using the OEM ignition switch as it will at least turn the starter eventually. I just worry that this problem will develop further at the wrong time.
Ford Ranger / B-Series :: 1997 - Blower Motor Doesn't Work
I've got a new to me 97 Ranger that the blower has never worked in and I can't get it going. I've checked the fuse. That's good. Tested the relay. That's good. Did an ohm test on the power switch for the blower. It's open in the "OFF" position and closed in the other positions. I've got continuity through the speed selector switch. New resistor and pigtail because the other one was nasty looking. What seems odd to me is that I've only got power to the blower motor relay at one terminal with the switch on (number 30 I believe). In addition, when I test the plug for the motor itself with my test light, one of the wires (org/blk I think) has power only when the switch is off. And I ran power straight to the fan from the battery and it spun right up. What am I missing?
View 8 Replies