Ford Ranger / B-Series :: 1997 - Fuel Injector Stuck Open?
I think a fuel injector is stuck open on my 97 Ranger 3.0. How can I check to see if I'm right and which one it is? I've heard about the "listening to the injectors" trick but I'm not sure what procedures to go through. Can I tell if one is open by taking them out and visual inspecting?
View 9 RepliesFord Ranger / B-Series :: Throttle Stuck Open Causing Truck To Move Forward When In 1st Gear
Have a 99 Ranger XLT, 4 cyl, manual transmission with 191K miles. Was running good as ever last night but went to start it this morning and throttle's stuck open, causing truck to move forward when in 1st gear. Even with clutch in, near impossible to get vehicle in or out of gear. Managed to get it into reverse, but truck was having none of it. What is the cause or causes of my trouble? Or how much the repairs might cost? I'm on the road so no chance of doing this myself.
View 2 RepliesFord F-150 - 1997-2003 :: Got Code P1518 - IMRC Replacement Or Actuator?
I have the P1518 code for Intake Manifold Runner Control. I can not seem to find if have the actuator itself only the electronic control which, I take connects to the actuator. Is the electronic portion the only thing that needs to be changed and clean the actuator butterfly with the manifold off, or does the actuator need to be found and replaced?
View 3 RepliesFord Ranger / B-Series :: IAC Open Up And Raise The Idle
My 04 ranger is back at it AGAIN. It started about 3 years ago.
- Cruising along on the highway and then come into town. Idles at 2000 RPM
- Shut it off. and restart it. Again, 2000 RPM.
- Shut it off and it idles normal
- Drive it 2-3 day and then it idles high again
- I have clean and functioned the IAC and it works fine
- Cleaned throttle body and I never can get it to stick.
- Replaced throttle cable
It still was idling high
- Replaced ECM and it idled normal for about 1 year
- Replaced em again and it idled normal for about 6 months
It is back at it again. For what ever reason the EM is telling the IAC to open up and raise the idle...
Ford Ranger / B-Series :: Heater Lever Stuck?
, my trucks heat selector lever, that controls the temperature in my truck, is stuck in the cold setting. by stuck I mean, I can try to move it, but it wont budge more than about 1/16" and no more. its really frustrating because of the cold weather here, and I want to have SOME heat in my truck without a bonfire to get it.
View 6 RepliesFord Ranger / B-Series :: 1983 With YFA - Inlet Gasket Stuck
I have a 1983 ranger with a YFA. I recently took it apart and in the process of the rebuild I noticed the metal gasket was still in the spot where the needle pin goes. It has adhered to the carb. Any way to get it un-stuck? Also, there is a module, and the gasket comes in the rebuild kit so I know it belongs, the part number begins with 2I3 but the rest came off with the dirt. What is it for and would it hurt anything if it wasn't plugged in? It hasn't been since I bought it.
View 2 RepliesFord Ranger / B-Series :: 1996 XLT - Ignition Key Stuck In Off Position
My ignition key is stuck / locked in the off position. The first time this happened I jiggled the key while moving the wheel back and forth and it turned. The next time in the truck nothing worked. I let it roll back a bit then tried, pushed the clutch in and put it in neutral, etc it did not move. (Just had the clutch and clutch hydraulics replaced.) The wheel is locked. The key removes from the cylinder.
I know it is easy to replace the Ignition Lock Cylinder when you can turn the key in the run position. How to remove it when locked in off?
Ford Ranger / B-Series :: 1997 - Harmonic Balancer Seems To Be Stuck?
I have been stuck at the tail end of the head gasket job on my 97 B2300. I have been working every day, so I haven't been able to get to this until today. The harmonic balancer seems to be stuck and I can't get it off. Regular 3 jaw pullers won't work (tried 4, rented one from the parts store that didn't work either) and tapping it from the back side while rotating the engine isn't working either. The pullers keep slipping off because the of the pulley's front ridge being slightly larger in diameter than the rest of the balancer.
Is there some kind of special puller that I don't know about? I don't want to be too rough with it as it seems no one carries this particular balancer if I happen to break it. Side question..... I was told that the crank/cam seals will also work on the oil pump as they are the same size. True? I happen to have 3 seals and wouldn't mind changing the oil pump seal as a precaution. (note this is a later 2.3 with a timing belt driven oil pump)
Ford Ranger / B-Series :: 1999 - Door Ajar Light Stuck On
Like the title says, my 99 ranger has the door ajar light stuck on, which in turn is making the dome light stay on. It's kinda been acting up lately, but would go out eventually. Today I washed it and had the doors open for a while. After I shut the doors and started it the light stayed on and hasn't gone off since. I pulled the negative cable tonight. And no, the doors aren't open! FWIW I cant pull the doors any tighter closed and make the light go out..
View 6 RepliesFord Ranger / B-Series :: 1985 - Shifter Really Loose / Stuck In Reverse
1985 ranger 2.3L TK5 tranny. Shifter was really loose and the tranny finally got stuck in reverse. I have opened up the bottom cover, but am not sure where to move the shift forks to get it back to neutral. I bought a new shifter, but I need to get the tranny back to neutral before I can install it.
View 2 RepliesFord Ranger / B-Series :: 1996 B2300 - Ignition Stuck In On Position
Took my 96 B2300 2WD SE (190k) to lunch. When I went to start it back up afterwards, the key turned but no starter engaged. All the dash lights came on, and now stay on. With the key in, I can turn the ignition freely...no clicking to different positions.
It springs a little when I turn it all the way, but still no starter. When I remove the key, the dash lights stay on, etc. So, since it was on, we were able to push-start it. I've parked it on a hill for now, and will disconnect the battery when I get it home.
Ford Ranger / B-Series :: 1987 2.3L - Seems Like Running On 3 Cylinder - Valve Stuck?
Having some trouble with my 1987 2.3L ranger - 2wd - Non AC - 107k miles.
The truck feels like its running on 3 cylinders and occasionally stalls. Motor has a pretty good shake to it while idling as well.
Recently replaced injectors, rotor, cap, wire, spark plugs. Timing belt was done approx 30k miles ago.
Put seafoam into it. Problem persists - where to go from here ?
Ford Ranger / B-Series :: Cruise Control Stuck On And Wouldn't Release
So I'm motoring along a country road with the cruise set at 50 mph and the truck starts to increase speed.
Tap the brake - nothing happens. I'm up to 65 mph! Knock it into neutral and it revs to around 3,500 rpms and then it unsticks.
What in the world is going on with that? After thinking on it, a few miles farther on and I set the cruise again.
It began immediately picking up speed. I hit the brake and nothing happened. Then I hit the off button and nothing happened.
So again I bumped it up into neutral and it did the same thing - revved for a moment and then kicked off.
The dealership where I get my service done can't get to it for several days. So I'm checking in the meanwhile to see possibilities to identify a cause.
Ford Ranger / B-Series :: 1993 - Tensioner Spring Is Frozen / Stuck
I have a problem with the serpentine belt tensioner, on a 1993 Splash; 4cyl motor. The tensioner spring is frozen/stuck, so it is set to where it is. Tried to 'exercise' to free it up, that did not work, and sorta' rounded out the 3/8 square hole doing that. So, ordered an new tensioner assembly. I felt around the tensioner mount at bottom, do not feel a bolt head. So it must be flat head allen or torx bolt, correct ?
View 9 RepliesFord Ranger / B-Series :: 2010 - Temporarily Disable Open Door Chime?
I tried moving a latch in the (driver) door to stop the chime from chiming when the driver door is open and the ignition is in the accessory position, but no luck. Looking for a solution for temporarily disabling the chime through some mechanical means? (2010 Ranger)
View 10 RepliesFord Ranger / B-Series :: 1994 B2300 - Grinding When Downshift To 4th / Stuck In 1st Gear
I bought the 94 B2300 from a guy that said he got it from an auction and didn't know much bout it. Got 30 mins down the road and went to down shift to 4th coming into town and all I got was grinding. Turned it off and it would go into other gears and start in gear with the clutch pushed in. Wen I tried to take off it wouldn't move and just died. Towed it home and installed a new clutch kit in it. Got the clutch bled and went to test drive it and now it is stuck in 1st gear. Can it be easily fixed or am I going to have to replace the transmission...
View 3 RepliesFord Ranger / B-Series :: 1996 - Fuel Gauge Stuck At Full Mark?
My fuel gauge is stuck at the full mark. What to check and where to start?
View 7 RepliesFord Ranger / B-Series :: 2003 - Heater Vent Selector Stuck On Defrost
There is always something.... I just drove my girlfriend's new 2003 ranger edge home from the seller. Real nice truck. I noticed the heater selector doesn't change the air flow. It is on full blast for the defrosters, and is also trickling out of the floor and dash vents. No matter where you put the selector, thats the only place the air comes out.
The temp control seem to work OK, when you turn it on cold, you get cold air and visa versa. Even on AC and MAx AC... air out the defrosters. It's cold when you turn the temp control to cold.
I did some searching here and gather some info on checking the vac lines etc. Everything looks in place but one detail. The vac ball under the hood under the air box has 2 ports on the front end, and only one grey line going into it. The other port has what looks like a rubber boot and part of a very short vac line broken off it.
I looked, I cant find any loose vac lines. I'd like to know if this second port is suppose to have a second line on it, and where does it go? What color is it? Is this the reason the vent selector isnt working?
Ford Ranger / B-Series :: 1998 Automatic - Shift Lever Stuck Sometimes In Park
It's a few times in the past 2 weeks, the shift lever won't come out of PARK easily. Sometimes I have to wiggle the shifter for quite awhile before I can get the shifter to shift out of PARK. It also doesn't start when that happens, like everything works but it doesn't start. It's like it's locked. It finally lets go and I can start it and put it in Drive and Reverse and go on my way. But there's not set thing that I can do to make it work.
It's just luckily let me go the few times it's happened. We replaced the shift cable about 1.5-2 years ago and of course the cable is out of warranty. But even if it's the cable, it's definitely going into park because you can hear the click when you stop the truck and turn it off, and throw it into PARK. But when the shift get's stuck it won't crank or make any kind of cranking noise, it's like the battery is dead but it isn't. When it happens you can't even shift it out of PARK to try and start it in D or R.
So I was thinking something could be going on with the NSS. Is there any kind of brake pedal interlock switch on a 98 Ranger? I notice when I start it and press the brake pedal it clicks loud under the dash, which I don't remember hearing always. But maybe it always makes that click when you hit the pedal because I usually always have the radio on. What I can do if the shift gets stuck when I go to leave work? What do I need to look at to determine the problem?