Ford Ranger / B-Series :: IMRC Stuck Open - Code P1537
2002 Ranger 2.3L, 5 spd, 108,000 miles
This has been from about 10,000 miles now. I have cleared the codes, sometimes it will go away for a day or two, but usually is back almost immediately. Finally last week I removed the solenoid and two vacuum lines hoping I would find a cracked hose like others have. No go there, but I replaced the vacuum lines anyway and dosed the vacuum ports on the solenoid with a little carb cleaner. Started truck up and revved it a few times, light stayed out. Next morning the check engine light was back on again.
Guess it must be in the actuator or the IMRC itself. Any success story about using some kind of cleaner to try to degunk this first (assuming it is stuck, that is...) without having to tear it apart?
Ford Ranger / B-Series :: Throttle Stuck Open Causing Truck To Move Forward When In 1st Gear
Have a 99 Ranger XLT, 4 cyl, manual transmission with 191K miles. Was running good as ever last night but went to start it this morning and throttle's stuck open, causing truck to move forward when in 1st gear. Even with clutch in, near impossible to get vehicle in or out of gear. Managed to get it into reverse, but truck was having none of it. What is the cause or causes of my trouble? Or how much the repairs might cost? I'm on the road so no chance of doing this myself.
View 2 RepliesFord Ranger / B-Series :: 1996 - Fuel Gauge Stuck At Full Mark?
My fuel gauge is stuck at the full mark. What to check and where to start?
View 7 RepliesFord Ranger / B-Series :: 1997 - Harmonic Balancer Seems To Be Stuck?
I have been stuck at the tail end of the head gasket job on my 97 B2300. I have been working every day, so I haven't been able to get to this until today. The harmonic balancer seems to be stuck and I can't get it off. Regular 3 jaw pullers won't work (tried 4, rented one from the parts store that didn't work either) and tapping it from the back side while rotating the engine isn't working either. The pullers keep slipping off because the of the pulley's front ridge being slightly larger in diameter than the rest of the balancer.
Is there some kind of special puller that I don't know about? I don't want to be too rough with it as it seems no one carries this particular balancer if I happen to break it. Side question..... I was told that the crank/cam seals will also work on the oil pump as they are the same size. True? I happen to have 3 seals and wouldn't mind changing the oil pump seal as a precaution. (note this is a later 2.3 with a timing belt driven oil pump)
Ford F-150 (2004-2008) :: 2005 - Injector Stuck Open - Shake Really Bad - Got Codes?
Well I believe I finally had the opportunity to experience the wide open injector issue. I was driving to work and all of a sudden at a stop light my truck started shaking bad. It went away but as I took off every so often it would shake. I thought it was a tire or front end component so I pulled over and just got overwhelmed with the smell of gas. I drove 30 miles back home and check engine light blinked the whole way and truck ran . Also wasted at least a 1/4 tank of gas and the a/c wouldn't blow cold air either. Hooked it up to read DTC codes and got P0172, P0300, P0303, P0304, P0316 and P2196.
View 14 RepliesFord Ranger / B-Series :: 1998 3.0L V6 - Injector Rail Leak
I bought a '98. At the front passenger side of the engine, the injector rail is leaking fuel (a fair stream of it). I have done some googling, and browsing around the forums, and can't find much in the way of specific info on where to start with this.
Whatever the device at the front of the rail - Without digging too far, it seems that the leak is coming just below it.
Questions:
Am I obliged to change injectors with the rail?
What is involved with changing the rail? Removing upper intake only? At all?
What is the box shaped device at the front of the rail, passenger side? Test port? Pressure Regulator? Both?
I won't have a chance to work on this again until next weekend, but thought I'd try to do some homework beforehand.
Ford Ranger / B-Series :: 1997 - Spit / Sputtered And Died - Fuel Pump Fuse Blown
I drove my truck 2 times the day it stopped running. The 3rd time I tried to leave it started moved about 2 ft, spit and sputtered and died. It had blown the fuel pump fuse. I changed it and checked the fuel shut -off in the cab, passenger side. It was not tripped. Tried to start it and as soon as I turned the key it blew the fuse again. I changed the fuse again and this time I changed the fuel relay and the switch in the cab. Turned the key and it blew the fuse right away. Went to AutoZone because they are close to the house described what it was doing to them and they said sounds like a short in the fuel pump.
I purchased a new pump put it in turned key blew the fuse, pump just clicked...I found this site and my son noticed a thread where it said wires under the cab are good for wearing through and grounding out. I looked and it did wear through one wire coating. We taped it up, put extra cover over it and now it does not blow any fuses. Fuel pump still just clicked. Took fuel pump back for an exchange.....same thing. Turns over but fuel pump will not pump fuel. What am I missing?......
Ford Ranger / B-Series :: 2005 Has Spark And Injector Pulse But Will Not Fire
I have a 2005 ford ranger, 4.0 auto, 4x4, 60psi fuel presser, has spark and injector pulse, will try to start if you hold the throttle a little over 3/4 the way down, but will not fire on starting fluid.
View 3 RepliesFord Ranger / B-Series :: 2000 - No Change In Idle When Pull The Injector Plug
Its a 2000 flex fuel 3.0... Its not the actual injector. I think its wiring or computer. No change in idle when I pull the injector plug. But I think I can feel the injector opening and closing. Compared to nearby injector diagnostic light flashes less brightly. but that's pretty hard to quantify
When I pull the plug on another injector it idles about the same but I can tell it surge up and down as I disconnect and reconnect it. Fuel injectors were backflushed and swapped same problem cylinder. Where do I go from here just take apart the loom and look for abraded wires? Its the number one cylinder, passenger front.
Ford Ranger / B-Series :: 1990 - Broken Fuel Line At Fuel Pressure Regulator?
I have a 1990 Ranger with a 4.0L that I just changer the intake gasket on. I broke the fuel line at the Fuel Pressure Regulator. Cant seem to find one anywhere. It is a nylon inside/rubber outside with a cloth mesh and quick connect fitting line. Where to get one? Can I hose clamp it the FPR by cutting off the connector that broke?
View 1 RepliesFord Ranger / B-Series :: IAC Open Up And Raise The Idle
My 04 ranger is back at it AGAIN. It started about 3 years ago.
- Cruising along on the highway and then come into town. Idles at 2000 RPM
- Shut it off. and restart it. Again, 2000 RPM.
- Shut it off and it idles normal
- Drive it 2-3 day and then it idles high again
- I have clean and functioned the IAC and it works fine
- Cleaned throttle body and I never can get it to stick.
- Replaced throttle cable
It still was idling high
- Replaced ECM and it idled normal for about 1 year
- Replaced em again and it idled normal for about 6 months
It is back at it again. For what ever reason the EM is telling the IAC to open up and raise the idle...
Ford Ranger / B-Series :: Heater Lever Stuck?
, my trucks heat selector lever, that controls the temperature in my truck, is stuck in the cold setting. by stuck I mean, I can try to move it, but it wont budge more than about 1/16" and no more. its really frustrating because of the cold weather here, and I want to have SOME heat in my truck without a bonfire to get it.
View 6 RepliesFord Ranger / B-Series :: 1983 With YFA - Inlet Gasket Stuck
I have a 1983 ranger with a YFA. I recently took it apart and in the process of the rebuild I noticed the metal gasket was still in the spot where the needle pin goes. It has adhered to the carb. Any way to get it un-stuck? Also, there is a module, and the gasket comes in the rebuild kit so I know it belongs, the part number begins with 2I3 but the rest came off with the dirt. What is it for and would it hurt anything if it wasn't plugged in? It hasn't been since I bought it.
View 2 RepliesFord Ranger / B-Series :: 1996 XLT - Ignition Key Stuck In Off Position
My ignition key is stuck / locked in the off position. The first time this happened I jiggled the key while moving the wheel back and forth and it turned. The next time in the truck nothing worked. I let it roll back a bit then tried, pushed the clutch in and put it in neutral, etc it did not move. (Just had the clutch and clutch hydraulics replaced.) The wheel is locked. The key removes from the cylinder.
I know it is easy to replace the Ignition Lock Cylinder when you can turn the key in the run position. How to remove it when locked in off?
Ford Ranger / B-Series :: 1999 - Door Ajar Light Stuck On
Like the title says, my 99 ranger has the door ajar light stuck on, which in turn is making the dome light stay on. It's kinda been acting up lately, but would go out eventually. Today I washed it and had the doors open for a while. After I shut the doors and started it the light stayed on and hasn't gone off since. I pulled the negative cable tonight. And no, the doors aren't open! FWIW I cant pull the doors any tighter closed and make the light go out..
View 6 RepliesFord Ranger / B-Series :: 1985 - Shifter Really Loose / Stuck In Reverse
1985 ranger 2.3L TK5 tranny. Shifter was really loose and the tranny finally got stuck in reverse. I have opened up the bottom cover, but am not sure where to move the shift forks to get it back to neutral. I bought a new shifter, but I need to get the tranny back to neutral before I can install it.
View 2 RepliesFord Ranger / B-Series :: 1996 B2300 - Ignition Stuck In On Position
Took my 96 B2300 2WD SE (190k) to lunch. When I went to start it back up afterwards, the key turned but no starter engaged. All the dash lights came on, and now stay on. With the key in, I can turn the ignition freely...no clicking to different positions.
It springs a little when I turn it all the way, but still no starter. When I remove the key, the dash lights stay on, etc. So, since it was on, we were able to push-start it. I've parked it on a hill for now, and will disconnect the battery when I get it home.
Ford Ranger / B-Series :: 1987 2.3L - Seems Like Running On 3 Cylinder - Valve Stuck?
Having some trouble with my 1987 2.3L ranger - 2wd - Non AC - 107k miles.
The truck feels like its running on 3 cylinders and occasionally stalls. Motor has a pretty good shake to it while idling as well.
Recently replaced injectors, rotor, cap, wire, spark plugs. Timing belt was done approx 30k miles ago.
Put seafoam into it. Problem persists - where to go from here ?
Ford Ranger / B-Series :: Cruise Control Stuck On And Wouldn't Release
So I'm motoring along a country road with the cruise set at 50 mph and the truck starts to increase speed.
Tap the brake - nothing happens. I'm up to 65 mph! Knock it into neutral and it revs to around 3,500 rpms and then it unsticks.
What in the world is going on with that? After thinking on it, a few miles farther on and I set the cruise again.
It began immediately picking up speed. I hit the brake and nothing happened. Then I hit the off button and nothing happened.
So again I bumped it up into neutral and it did the same thing - revved for a moment and then kicked off.
The dealership where I get my service done can't get to it for several days. So I'm checking in the meanwhile to see possibilities to identify a cause.