Ford Ranger / B-Series :: Ball Hitch Won't Remove?
I know this sounds pathetic but i cannot get the ball hitch off of my truck. That thing is on there and i cant get it loose because the ball keeps turning when i try to break the nut loose. I have tried several ways to keep the ball still but they don't hold it enough for me to get the nut loose. I dont care about keeping the hitch i am trying to put a smaller one on and don't need it so if i have to break it to get it off i don't care.
View 4 RepliesFord Excursion :: How To Remove The Cup-holder Cover
I need to send my cup-holder cover and trash hook to Clay so he can color match my F650 dash and I can't figure out how to get the damn side clips on the cup-holder to let go!
I got the top clips and the bottom clip to let go but the side clips will not slip through the slots... I've been near the point of breaking them trying to slide them through...
Ford Ranger / B-Series :: 1996 - Removing Bed - Should Remove Spare Tire Too?
Broke one of the shackle brackets. Planning on pulling the bed and doing all four. I've searched and read as much as I can in a short period of time. I have a few questions about bed removal.
1. How hard is it to remove the factory plastic bed liner?
2. Do I need to remove the spare tire to get to any of the bed bolts.
One reason I decided to remove the bed is I can't get the spare out. I figure I'll be able to fix that as well once I have the bed off.
Passat (B5) :: 2000 - How To Remove Cup Holder
My cup holder sticks and will not come out like it should. I believe me brother had spilled some coke on accident. How to remove it. Or maybe give me a "how to" link they know about. I tried searching for this but, I could not find anything. I have a 2000 passat.
View 2 RepliesFord Super Duty (1999-2016) :: 2008 - Fold Down Console - How To Remove Cup Holder Part
I was wondering how do you remove the cup holder part of the console dose it just pop off or are there metal clips or screws hidden some how?
View 4 RepliesPhaeton :: How To Remove The Ash Tray / Coin Holder
I'm trying to install an iPod dock inside the coin tray. How to remove the coin tray? The iPod dock fits in it perfectly width wise, but the length is a bit long so I need to remove it so I can drill a slot inside it.
View 4 RepliesPrius V :: How To Remove The Center Console Cup Holder Drawer
I have a 2012 Prius V, and somehow A tin of Altoids has fallen behind the drawer, (hidden drawer) of the center console. How to remove the drawer to access behind it?
I can't see any catch or release to trigger releasing the drawer. I also think accessing it by opening up the whole console from the top is risky as the EV, ECO, and PWR mode buttons are wired into it.
Ford Ranger / B-Series :: 1988 - Press Key Lock To Remove Key - Disable Key Lock?
On my '88 Ranger, there is the key lock that needs to be pressed to remove the key. When I changed the ignition cylinder, I darn near went ahead and removed it. I though I better check here first, and see if I was going to disable some other function I don't know about.
View 1 RepliesFord Ranger / B-Series :: CEL On After Oil Change?
I just changed my Oil, added a FRAM filter and bought some good Quakerstate High Mileage and my truck runs good. However, I noticed that my Check Oil light is constantly on. I also recently changed my Oil Sender, and I wonder if that has got something to do with it.
View 3 RepliesFord Ranger / B-Series :: Transmission Is Going Out
I have a 1994 2.3l 4cylinder xlt ford ranger regular cab Manuel transmission. My transmission is going out. I found an 04 ford ranger Manuel transmission off a v6 will this be compatible? And if not what years will be?
View 2 RepliesFord Ranger / B-Series :: Shaking Really Bad When Get To 35 MPH
I have a 1994 ford ranger 4x4 that I just put on and 35's and when I get to 35 mph it shakes really bad. What the problem is. Have been told that I need a steering stabilizer.
View 9 RepliesFord Ranger / B-Series :: AC Cycles Off And On
I need to change the AC relay. What is the location of the relay.
View 6 RepliesFord Ranger / B-Series :: Throttle With A/C On?
I have a weird issue. When I'm running AC on my 2.3l ranger sometimes the idle wont go down but rather hold its current RPMs till i either turn the AC off or place the truck back in gear. What that could be?
View 6 RepliesFord Ranger / B-Series :: 3.0 VS 4.0 Engine?
Opinions welcomed...thinking of taking a gamble on an '04 with 248k miles on it.....not sure what engine is in it.
View 14 RepliesFord Ranger / B-Series :: One Hub Locked In 4X4
Hello. I never did this before but could you lock one hub in 2wd and leave the other unlocked. Also can you leave one hub locked while in 4wd? I was thinking if you have one hub locked would all the power would go to that wheel? Or will this do damage?
Thanks
Ford Ranger / B-Series :: 2wd To 4wd Conversion
I fit explorer rear axle to my 2wd ranger. But now I have fromt x-member with front suspension and front drive axle from explorer. Can I fit all this stuff to my ranger?
View 2 RepliesFord Ranger / B-Series :: 1997 - Possible 4.0 To 5.0 Conversion?
I recently purchased a 1997 Ford Ranger with a blown 4.0 with a 5 speed , I have a 5.0 with a Carb and 5 speed out of a 80s mustang . Is it possible to use this in the 97 Ranger , I understand I need a different fuel pump but motor mount wise I was hoping it would fit.
View 2 RepliesFord Ranger / B-Series :: Code 157 For MAF Sensor
So here is what I got. Code 157 maf sensor below minimum voltage. Here is what the truck does. When the MAF is plugged in and I step on it, the truck surges and when it drops below 1k rpm it dies but I can start it back up. If I hold the throttle at 1k it stays alive. When I drive with the MAF unplugged it runs better no surging but it still dies. Here is what I have done. Reset codes no change, put new MAF in no change. I have traced all 4 MAF wires checked continuity from inside of plug to inside of plug.
All wires checked out good. No cuts breaks or anything. I have checked my battery, starter, and alternator ad all check out fine. I read that someone said if the corresponding transistor in the PCM took a dumb then it would cause not enough voltage to get to the plug because the transistor would dump the voltage from the battery leading to the MAF. I thought about running a direct power source from the battery to the voltage side of the MAF with a switch in the truck to just see if that would solve the issue but I don't know if that is possible or smart.
Ford Ranger / B-Series :: Blinkers Would Only Flash Once
Ok first I am not super-mechanically inclined but i'm pretty smart and a fast learner, lol. That said I have a 1999 Ford Ranger and two nights ago first one blinker stopped working and then an hour later the other one stopped. What I mean by "stopped" is they weren't turning on at all.
Ok so, the flasher lights are all working when turned on. I went to the auto parts store and they said I needed a new flasher. I bought it but they weren't sure which one to replace. Well there were only 3 that size in the box under the hood so I used the process of illumination. Except the new one didn't exactly fit the first one so i tried the two others. Well when I think I had it in the right one.
The Blinkers would only flash once and then that was it. The guy at the store said the flasher may be faulty but he did not have another one so he gave me my money back. I noticed on the way home that the blinkers would still flash once even with the old flasher in place. The 4 way flashers still work normally so all bulbs are working.