Ford Ranger / B-Series :: 1987 2.9L - Which Transmission
Which transmission came with the 1987 Ranger 2.9L?
View 4 RepliesFord Ranger / B-Series :: Top 2 Bolts Removal Of Transmission?
How in the heck do you get the top 2 bolts off of the transmission housing? They seem to be positioned in such a way that they are impossible to remove.
View 14 RepliesFord Ranger / B-Series :: 1982 - Transmission Won't Engaging?
I've got a 1982 Courier 2.0 2wd 5speed pickup and it's been passed down through my family and has sat for quite a while so I started tinkering with it in my spare time.
I began with the motor and got it to run after 15 years of sitting around but am having issues with the transmission. When I first got it running a while back i had it in gear and when I let out on the clutch it lunged forward a little and stalled. I have since then towed it a short distance across my yard (in neutral of course), but now it seems like it isn't doing anything while it's in gear.
While its running I can put it in gear (even without the clutch) it doesn't grind jump or anything. Everything feels like it's okay as in going into all the gears. I was wondering if this is possibly clutch related or if it's the trans itself. Or maybe some electrical thing related. I haven't taken anything apart yet in hopes that it's something simple. I was curious if it might be low on fluid and maybe that would cause it not to engage properly?
Ford Ranger / B-Series :: 1990 - Can Convert 4x4 Transmission To 2x4?
I have a 90' Ford Ranger, rear wheel drive.
I can not find a 2 wheel drive automatic transmission and I was wondering if I can convert a 4 wheel drive transmission?
Ford Ranger / B-Series :: Transmission Goes Into Limp Mode When AC Turned On
Turn air conditioner on transmission goes into limp mode??
1999 ranger 2 door 2,5 engine long wheel base,,auto trans.
2wd no power windows no power seats....
Ford Ranger / B-Series :: Transmission Slipping / Won't Pull In Reverse
I'm having trouble with my auto tranny again. it is a 4r44e and is in a 1999 3.0 flex 2wd extended cab. It will not pull in reverse, seems to be slipping bad, and it won't pull in forward gears unless you switch OD off. Then it seems to pull fine but still not in reverse. I haven't drove it very much to see on changing gears and such for fear of burning it up.
Fluid is still like new no codes showing just started out of the blue while my son was driving. All electrical is hooked up tight and no leaks fluid is little overfull but not much. I am going outside now to adjust intermediate band to spec. had trouble with overdrive that had everybody stumped if you remember and it was overdrive band adjustment so going that route first.
Ford Ranger / B-Series :: 1987 4x4 V6 Transmission Slips Out Of Gear
I have a 1987 ford ranger 4x4 2.9l v6 but my transmission slips out of gear and its auto im not sure why but ive been told im missing a over drive gear is this a possibility or what???
View 1 RepliesFord Ranger / B-Series :: 1996 - Transmission Slipping When Cold
I have a 1996 Ford Ranger with 95k miles on it. Recently, my truck's automatic transmission has been slipping really bad. I'll be driving down my road and while going around a turn, the clutch feels like it randomly disengages, so when I press on the gas, it feels like I'm revving my truck in neutral, and then it will all of a sudden get back into gear, violently a lot of the time. However, once the truck is warmed up, the it runs perfectly and never slips. I've checked my oil multiple times and even changed the oil filter in the transmission. I am not sure if this has anything to do with it, but if I let my truck idle in park for a little bit, the RPMs will increase and if I shift in to reverse or drive while the RPMs are high, it'll do the same thing.
View 14 RepliesFord Ranger / B-Series :: 1997 - Transmission And Clutch Interchange
Will a clutch/flywheel and 5 spd from a 1997 ranger bolt up to an older 1980ish engine that had a 4 spd? What about the starter?
View 1 RepliesFord Ranger / B-Series :: Transmission Swap From 1996 To 2000?
Will the transmission from a 2000 fit a 96? They're both 3.0's.
View 3 RepliesFord Ranger / B-Series :: 1990 - Front Transmission Seal Went Bad
I've got a 1990 ford ranger 4.0 auto trans front transmission seal went bad, I've got everything unbolted abs ready to come put but the trans won't come over top of the front cross member, what could be the problem on why it won't come out?
View 3 RepliesFord Ranger / B-Series :: 1997 - Transmission Not Shifting Down Into First Gear Not Even Manually
I just had a 97 Ford Ranger with a 3 speed overdrive transmission in my garage that we replaced the transmission because it was not shifting down into first gear, not even manually!. The new transmission is doing the exact same thing as the original.
View 5 RepliesFord Ranger / B-Series :: Transmission Adjustment / Rough Downshift Into 2nd Gear About 15 Or 16 Mph
My 93' Ranger XLT extra cab 2wd, 4.0 engine and A4LD auto tranny with 126,600 miles has a rough downshift into 2nd gear about 15 or 16 mph. Down shift to 1st is real smooth and upshifting thru the gears is smooth. I just put a new modulator valve on it and upshifts smooth out, they were getting to be hard shifts before changing that valve. I do not know if there is any adjustment that can be made to smooth out the rough downshift when slowing down to a stop for red light. The U-joins are in good shape and new carrier bearing assembly on driveshaft and no extra play in the rear end. A band adjustment maybe or just have to live with it.
View 5 RepliesFord Ranger / B-Series :: Transmission Went Into Limp Mode With O/D Light Flashing
2001 Ranger 3.0 liter has developed a transmission casualty. I was driving along at 30 mph and the transmission went into "limp' mode with O/D light flashing and truck will only barely creep along with high engine rpm. When I got the truck home I was able to retrieve a p0720, output shaft speed sensor signal fault. I had hoped that replacing the sensor would solve this casualty.
Of course this was not the case. I have read all the posts I can find for this particular fault and realize that I must electrically trace the continuity of this circuit and also ensure that it's not grounded. I have been unable to find the needed wiring diagrams or pin out information.
Before I have to try and blindly start pawing through the connectors I'm looking for the pinout for the PCM and perhaps the bulk connector above the engine between the PCM and the transmission wiring harness. I am also keen to hear of any diagnostic tips that I may have overlooked.
Ford Ranger / B-Series :: 1989 Automatic Transmission Shifts Hard Into Second
I got this 89 ranger xlt with a 2.9 and automatic transmission. I mainly bought it because it was in such good shape and I was planning on putting a 5.0 in it. everything works on it. the a/c, radio, lights and it runs real nice. the only problem it has is it shifts pretty hard going into second gear. every once in a while it will shift smoothly into second but only like once or twice a day. he said he had recently changed the trans filter and fluid and the fluid does not smell burnt.
View 7 RepliesFord Ranger / B-Series :: 1996 - Transmission Grinds When Putting It In Reverse
I own a 1996 XL Ford Ranger 2wd 5 speed manual.
Last week I had it in for some service, which included bleeding the clutch lines and new fluid.
Since then when putting it in reverse the transmission grids. It is also very difficult to get into first gear - I really have to shove hard on the stick.
Better Description of symptoms: When the vehicle is moving it shifts fine. When I come to a stop, put it in neutral and let out on the clutch, it is then very difficult to get back into first gear. If I leave the clutch in, fter I come to a stop, I can shift around to all the gears no problem. It's only when I let out on the clutch, then push it back in to shift into first is the difficult part.
With reverse, I have to move ahead a bit, THEN I can shift to reverse without the grinding noise. I talked to my mechanic who check to ensure the fluid was NOT low (it wasn't) and no air bubble existed in the line. After that was checked, he said the clutch is worn and has to be replaced.
Well, then, why wasn't it doing this BEFORE I had him bleed the lines? It started the day I picked the truck up from service. He recommends the following to fix the problem...
- slave cylinder
- new line
- disc
- preasure
I am asking why this would happen after he bleed the lines? Is there another problem that can cause this?
Ford Ranger / B-Series :: 2003 - Hard Shift - Transmission Or Clutch?
The truck: 03 Ranger, 2wd, 2.3L, 5spd, 160k mi
I bought the truck two years ago and it's always been difficult to shift (especially into 1st, 2nd, 3rd). I don't drive it often and only put 5k mi on it since I bought it.
The problem: Someone more mechanically inclined than I once told me that the hard shifting is probably due to the clutch not fully releasing due to low hydraulic pressure brought about by a failing slave cylinder.
I just noticed today that there is a high-pitched squeaking coming from somewhere on the truck. At first, I thought it was the rear end, but now, after pulling it into the driveway, I noticed that the squeaking noise vanishes when I push in the clutch pedal and returns after I release the clutch pedal and drive in 1st gear.
The transmission oil level is good, but I've never changed it and I'm not sure if the previous owner ever did either. I'm hoping I haven't damaged the transmission.
After reading a few threads, it seems the problem might be the input shaft bearing. To replace it, I'd need to drop the transmission and borrow a couple of tools I don't have (feeler gauge and bearing puller). If the ISB is the problem, it seems like it would be a good idea to change it now before it seizes and leaves me stranded somewhere.
Ford Ranger / B-Series :: 2000 XLT - Transmission Slips When Starting From A Stop
2000 Ranger XLT 4x4 3.0L Auto
So a couple months ago I had a transmission problem. It shifts high and hard all times and after the "od" light gets going (after it gets warm), the transmission slips (like riding clutch) when starting from a stop. If I went from drive to 1st gear with the selector and back, it cleared the slipping problem for a bit. I did an oil/filter change and about 50 miles later the truck is running fine, no issues. One day I hopped in it to go to work and it was like nothing ever happened. Fast forward 1,500 miles later. I start to notice the transmission is subtly shifting weird, like a small jerk when shifting. It gets worse over 50 miles and now I am back to the above problem. Is there a way this could be a sensor or solenoid problem? I never heard of a transmission correcting an issue then starting at it again so much later.
I don't like fixing or working on an issue unless I am at least 95% sure what the problem is. I also don't have $2k to plop down on a repair at the moment. Would it be worth it to take this to a dealership and see what trouble codes I am getting? I would try a transmission shop but it's not guaranteed they will have the test equipment to check a ford transmission. Also a friend said that AutoZone and other stores can't check transmission codes. So what's the best option here?
Ford Ranger / B-Series :: 1993 A4ld Transmission Fluid Not Circulating
I have a 1993 ranger 3.0L/6cyl/automatic/ a4ld. I replaced the transmission and torque converter with one from a salvage yard that has approx. 76k miles. I added tranny fluid and idled the engine for approx. 10 minutes in neutral, but the fluid has not begone to circulate. I pulled off the trans line at the radiator and there is no flow with the engine running in park. Where should I start with the diagnostics for this problem?
View 4 Replies