Ford Ranger / B-Series :: 1989 Truck Jerked Really Hard - Lurch When Clutch All The Way Pushed Down
I have an '89 Ranger, Extended Cab, 2x4, 2.3l, Manual transmission with 255,000 on the odometer. I've owned it since 1990 and as far as I can remember it has either never had a clutch or only had one. I realize it's past due.
Everything has been fine up until this morning. 10 minutes after leaving the driveway this morning going a steady 55mph, no incline, it sounded almost as if I hit a deer. The truck jerked real hard, I put it back into 5th, and limped to my destination. Keep in mind for the next 30 or so miles there was absolutely no clutch slippage.
Here's the symptoms: No slippage, won't go into gears (I have to match rev's and shift without clutch, I drive a big rig and do this daily), when I do get it in 1st at a stop sign it wants to lurch with clutch all the way pushed down, I still have a great clutch pedal, and the most interesting thing to me is it sounds like something is being tossed around in my bell housing.
I'm almost 100% certain it's the clutch, however, I just wanted to come on here and report I have no slippage and it sounds like something being tossed around in the bell housing area. Is it possible a piece of the clutch could have "broke" off and that was what that huge jerk at 55 mph was? Approx. how much would a shop charge to put a clutch in on this model? I live in a rural area where prices are not inflated.
Ford Ranger / B-Series :: 1984 - Stalling When Approaching A Stop Sign Or Light
It's an oldie, 1984, but so far still kicking. 6 cyl 2.8, carb. I took a little couple hundred mile trip a few weeks ago. Rolled back into town no problems.
A few days later I took a ride and the ranger would stall when approaching a stop sign or light. I would hold the pedal down a little to keep it running but it sounded like it wanted to die if I didn't feather the pedal to rev a bit.
I drove a few days later, as I was going down the neighborhood road(25 mph), it acted like it wanted to just die. I mashed the pedal and it had no effect. It didn't stall and eventually I could rev the engine to continue.
It continues to do the same, then will all of a sudden take off like there was never a problem. If/when it does stall again, it can be hard to start until it does start and off I go again like there was never a problem. Other times, it will idle.
Another note: Sometimes when I go to start the engine it will stutter, intermittently turnover. It has done the same thing while actually driving, kind of a jerking deal.
Fuel filter, fuel pump, electrical? I'm going to first check/replace the fuel filter tomorrow.
Ford Ranger / B-Series :: 1999 - High Idle - ECM?
I have a 99 Ranger w/3.0. It idles about 1500 rpm cold,and 1200 warm. Here are the things that I have tried.
1.Checked ALL vacumn hoses/lines
2.Changed Air idle control sensor
3.Throttle position sensor
4.removed and completely cleaned throttle plate in throttle body.
5. removed top of intake manifold and checked for cracks and/or leaky gasket.
Nothing seems to change. Could it be a faulty ecm?
Ford Ranger / B-Series :: 1992 - Very High Idle At About 3500 RPM
My 92 ranger, 2wd, 6 cyl, manual trans, is running at about 3500 rpm at idle. I was wondering what might be the cause, maybe something with the throttle or could the gauge be screwed up.
View 14 RepliesFord Ranger / B-Series :: 1987 XLT - High Idle When Started For About 6 Minutes
My ranger 2.9 automatic 2WD has an high idle when started for about 6 min, engine can be hot or cold, still get the high idle, then it will drop to around 900-1000. I've changed the Idle control twice, checked EGR function. Replace temp sensor. Disconnected battery for 15 min. No code output.
View 7 RepliesFord Ranger / B-Series :: Stumbling And Sometimes Stalls After High Rev Coming Down To Idle
My truck has been doing this since I got it and I can't figure it out. It's a 2000 Ford Ranger XLT 2.5 5Spd. It runs fine if you don't rev it above 2500-3000 rpm. After you rev it that high coming down to idle it is stumbling real bad and sometimes stalls. I've been driving it like this since I got it, and it does fine other than this. It gets better the longer you drive it, but it still will do it if you rev it high enough.
Here are all the parts I personally have changed (previous owner said he did the plugs and wires and air filter, which it looks like he did but I'm about ready to change them myself):
-Fuel filter
-coil packs
-timing belt
-egr valve
-cleaned throttle body
-iacv
-tps
-thermostat
Ford Ranger / B-Series :: Extremely High Idle At 2500 To 3000 RPM
Ranger often wants to idle at 2,500 to 3,000 rpm. I'm glad its got a clutch! This is a long term intermittent problem that is getting worse. I have replaced the the IAC twice. I have unplugged the IAC when the engine is in high idle and the engine idles normally. But, starting the car with the IAC unplugged makes car run rough. That makes me think the IAC is not getting the right voltage input from the pmc (eec). Mine is a 2002 with the 3.0 engine. Throttle plate seems to be closed.
What sense inputs does PMC use to determine idle air position? Also replaced TPS sometime ago but that didn't work either. Sometimes turning off the a/c will knock the idle back to normal but not always. Turning the car off completely usually resets idle. But the high idle comes right back after accelerating. Drove the car today and idle would stick and stay high when clutch pushed in coming to a light. However. as the car slowed to a stop the idle would come down when rolling 1-2 mph. ??
Ford Ranger / B-Series :: 1999 - Rough And High Idle At 850 RPMs
1999 B3000 with a 3.0. The truck idles at 850rpms. When it starts it idles at around 1000 and runs very rough. When I disconnect the IAC the engine dies. The AC also has problems it blows cold at idle but at highway speeds after 7-8 minutes running the compressor kicks out. One can turn it off and it blows cold again after a few minutes.
View 5 RepliesFord Ranger / B-Series :: High Idle At Start Up / Revs Up Over 2000 RPM
I have 95 ranger 3.0L revs up over 2000rpm at startup then comes down slowly to a little over 1000... Changed the IAC valve still does it... When I let it warm up I unplug the IAC and idles normal and smooth about 750 RPM so I don't think it's a vac leak... What else could it be???
View 5 RepliesFord Ranger / B-Series :: 2003 3.0 V6 - High Idle In The Mornings When Cold About 2000 RPM
Truck is a 2003 Ranger EDGE 2wd auto w/140K miles (looks new) that was a one owner truck I recently bought. Came from Texas and is clean and was well maintained I got all service records up until I bought it in the fall last year. OK now the problems...
First...it has a high idle in the mornings when cold about 2000RPM. After it warms up it settles to about 800-900RPM but is VERY ROUGH to the point where it feels it will stall. I DID replace the spark plugs and the plug wires look newer and are not OEM. I DID remove and clean the IAC and it does not look very dirty but I did slightly clean it anyway.
When I did this I disconnected the battery for 20min. After I put it back together it ran smooth for about the first 10 minutes then same rough idle came back. I was told this truck has no EGR so that's not an issue. There are NO CODES and when I ran my pocket scanner nothing comes up either. Should I just go to NAPA and get a new IAC anyway? What else can I do?
Ford Ranger / B-Series :: 2003 - High Idle And Shoot Up Between Shifts / No Codes
My '03 Ranger is having a high idle problem. It's a 3.0, manual, 2wd, 141,000 miles. When it's cold it will idle at about 1500 but once I drive it, even just to the end of the block, it will idle at about 3000 and shoot up towards that between shifts. At a traffic light it will idle at 3000 and maybe go down to about 2500. If I bog it down with the clutch it goes right back up once I put the clutch back in or put it in neutral.
I replaced the IAC, no luck. I cleaned the MAF and checked the voltage on the TPS and it is good. I replaced the PVC valve, but the old one was fine anyway. I've sprayed around with carb cleaner and don't notice any difference. I've plugged it into my dad's AutoTap which lets me monitor everything on my laptop and the only thing I can see that looks suspicious is that even with the engine off, the Absolute Throttle Angle reads 18.8%. If I step on the gas with the engine off it goes up to 91.8% so I would imagine that just has to do with the function of the TPS and probably isn't out of the ordinary, but I don't really know what that number means or what the Absolute Throttle Angle is or is supposed to be.
Short of taking the intake plenum off and physically inspecting it for cracks, I'm stumped.
Ford Ranger / B-Series :: 1997 V6 - High Idle At 2500 RPM When IAC Is Plugged And Steady 1100 When Unplugged
I have a 1997 Ranger with a 3.0 v6 with a super high idle.
It idles at 2500 RPM when the IAC is plugged and a steady 1100 when unplugged. I have replaced the IAC twice now (dropped the first replacement. long story) and and have also checked for vac leaks with no results.
After about 2-3 minutes of idling at 2500 on a cold start it will drop down to 1100 (same as when IAC is unplugged), but after a 10 minutes or so drive it will idle steady at 2500 with minimal if any dropping in RPMs. This is driving me crazy not only because it sounds horrible but also because of the fact it's burning through fuel like it's going out of style.
I have checked the MAF sensor and it looks brand new (not the original owner) along with the O2 sensor. I have been meaning to check the TPS voltage to see if it's working correctly but without a working multi-meter it's making it difficult to do anything.
I'm at a loss with this right now and because of all the previous repairs i have done to it and the others that still need to be done i don't have the biggest budget to fix this problem nor the money the truck is using in gas.
Ford Ranger / B-Series :: 2000 - Fluid Coming Out When Pushed The Pedal After Blown Rear Line
A few weeks back just after buying a new front hub assembly (so I know I have Live Axle 4x4 and 4WABS), a dude on an excavator pulled out in front of me on a blind curve on an interstate exit ramp. Almost got him, then almost got got by the car behind. The hard stop caused a rear line to blow.
When I got home, fluid was still coming out when I pushed the pedal, so the first thing I did was top off the reservoir. I was surprised it was not empty.
I finally got lines that would fit, and replaced both sides. Fast forward a few weeks and I had time to bleed the system. I hooked my vacuum pump to the right-rear wheel cylinder port, opened it and began to pump. Pump, pump, pump, and still no fluid. Tried a few times. Left the pump on, opened the port, (charged the battery), started the truck and pumped the pedal - no fluid. Also, the fluid level did not change in the master.
Master cylinder bleed? Do I need to have the ABS motor bled?
Ford Ranger / B-Series :: Stumbling Idle And Check Engine Light On
So i have a 2000 ford ranger 2wd 4cyl .190k miles. My issue is the motor has a very rough/shaking idle,abs light on,and check engine light on.it also continues to blow fuses to the tail lights and dash, haha
Ive had it since it was at 40k and has been a great truck,although lately i have really neglected it.ive changed the spark plugs and new wires new timing chain. I would d love to start trouble shooting some of this stuff this weekend if the weather holds up.
Ford Ranger / B-Series :: Rough Idle - Check Engine Light Starts Flashing
My 3.0 with 216k miles has developed a rough idle and it progressively got better with new parts and cleanings. On startup it revs up to 2k then back down to 600. If I let it idle for about 8 or so minutes my Check Engine Light starts flashing. If I drive about for a little bit it stops and is just fine.
While the light is flashing I get codes P1000, P0305, P0306, and P0316. Which are OBDII Monitor Testing Not Complete, Misfire detected in Cyl 5, Misfire detected in Cyl 6 and Engine Misfire Detected on Startup (First 1000 Revolutions) respectively. Any other time the truck runs like a dream. Gets 20 city and 29.5 highway.
I cleaned my Mass Air Flow, replaced my Idle Air Control, SeaFoamed throttle body and vacuum lines, brand new coil pack, new wires, new plugs, new fuel filter, I've only ever run 91 octane, Chevron with Techron goes in at every oil change and B12 every other and I just ran 3 bottles of Lucas fuel injector cleaner.
Ford Fuel System :: 1991 F150 - Idles High At Around 2600 - 2800 RPMs
I just bought a 1991 F150 with a 302 (5.0). It idles at around 2600-2800 RPMs. The previous owners replaced the TPS and IAC, but it still idles fast. Ford dealership told them it was a vacuum leak. Are all the vacuum lines close to each other? How easy is it to locate/fix the problem?
View 2 RepliesFord Ranger / B-Series :: Clutch Would Not Disengage At Any Time
This morning, I shifted into neutral and left the truck running. When I got in it put it in reverse, the shifter peddle went all the way to the floor and the clutch did not engage. I turned off the engine, and the transmission shifted easily. I put it into reverse, started the engine, and when I tried to shift back into first, the same thing happened. Pedal to the floor with no resistance, and I could not get it into gear. I finally forced it into 1st to get back into the driveway, but had to stall the engine to keep from going through the garage door. The clutch would not disengage at any time. I checked the master cylinder and it is 1/2 full. Has my clutch gone out?
View 14 RepliesFord Ranger / B-Series :: 1999 XLT V6 - No Clutch / Can't Shift
When I got home today I went to back into my parking spot and couldn't get my truck in reverse, or any other gear for that matter.
I've been suspecting something was going to go wrong because the last few weeks or so when I push the clutch in it sounded like bb's rolling around in a metal coffee can. Since I have owned it (2 yrs) the clutch has seemed funny anyhow, as in I really have to feather it so it doesn't grab and stall out.
So I've visually inspected what I can so far. Master cylinder fluid is at a proper level and I pulled the inspection cover on the transmission. I didn't see any fluid and reached inside and there wasn't residue in there either. I observed the throwout bearing pushing the clutch cover fingers in when the pedal is pressed and that is about it.
Just wondering about some additional checks I can perform to pinpoint the problem, as well as how to fix it and get rolling again.
1999 Ford Ranger 4x4 XLT
3.0 V6
134,xxx miles
No modifications
Ford Ranger / B-Series :: AC System - Clutch Goes On And Off When Add Freon
2003 Ford Ranger .. ac:system is over pressurize when I add freon the clutch goes on and off.Is there a high pressure switch for something
View 1 Replies