Ford - Suspension :: Pressure In Fill Line Keeps Shutting Off Gas Pump
I have 2002 Ford Explorer and I have trouble filling it with gas. The pressure in the fill line keeps shutting off the gas pump. I have to slowly drizzle the gas in to fill the tank. Sometimes the problem is better, sometimes worse.
View 4 RepliesSaturn :: 1995 - Gas Pump Keeps Shutting Off When Try To Fill
The gas pump keeps shutting off when I try to fill my '95 Saturn, like it would when the tank is full, even when the tank is empty. This is a recent phenomenon, and it does it at every gas pump. I have to keep pulling the handle to get gas in the tank. I took off the filler tube and checked both it and the vent line. Both are clear. What could be causing this?
View 2 RepliesFord Super Duty (1999-2016) :: Hard To Fill Up At The Pump After Canister Replacement
My 06 f250 with the 5.4 has a hard time being filled at the pump. So I followed the tsb and replaced the carbon canister, filter box and solenoid with the kit from my local ford dealer. Before it was impossible to get fuel in. Now it is way better but I have to fill it up with the gas nozzle upside down in order to fill at full speed. I have blown out the vent with compressed air.
View 6 RepliesFord Ranger / B-Series :: 2002 - Shutting Down While Driving
Our Ranger, 2002, 4 cyl. 2.3 5 speed is shutting down while driving. This has happened twice very recently. Both times on interstate at highway speed. First it loses power then completely shuts down. After stopping, turning key "off" it restarts and runs fine. It does take a longer time to crank before starting.
It is not throwing any codes and the CE is not coming on. I suspect the fuel pump is shutting down. Seems like fuel pressure loss is reason for loss of power? Then extended cranking to restart is the initial build up? What else could it be? If not the pump itself, is there something that would take away power from the pump then get reset?
Ford Ranger / B-Series :: 1993 - Location Of The Fill Plug?
Where is the location of the fill plug for a 93 Ranger transfer case? The damper is off and I see the drain plug. Is the fill plug behind the electric motor that shifts the case? I can see what may be a plug there that looks plastic with a very small hex head in the center of it. Is that it?
Also, my Haynes manual says to use Mercon ATF in the transfer case. I see where Valvoline has a Mercon equivalent. What do ATF brand people here recommend?
Ford Ranger / B-Series :: Vacuum Hose Diagram?
Where I might be able to find a vacuum hose routing diagram for a 2.9? I have searched high and low but with no luck.
View 14 RepliesFord Ranger / B-Series :: Fan Only Work At High Speed / Blower Motor Hose?
I recently bought a 96 ranger.I noticed the fan did not work but for high. I search the internet and found how to remove it and discovered a mouse nest(village) which basically took over the housing where the evaportor core,blower motor resides. I bought a chilton but cannot remove the housing around the core so I cleaned it the best I could(air compressor and vacuum and disinfectant)...
I had to buy a new blower motor and resistor. However, I cannot find the hose that attached to the blower motor?-mouse had chewed a hole in the one- I've looked and found serveral differents names for it but seems I cannot find it at my local parts store.
My question is- is this intake hose? vent hose? I'm guessing I will have to go to dealer or, if I know the name I can look it up in a salvage yard?
Ford Ranger / B-Series :: 1989 - Heater Hose Leaking Around Behind The Valve Cover
Found a tee on the heater hose leaks when it warms up. Appears the PO had noticed it but put a hose over it and now is leaking around behind the valve cover. This is a hard plastic line around 5/16. No online parts show it as being available. Is there a fix for this ?
I would bet several others have had this problem as it lays right on top of the flange of the valve cover where I think it would rub a hole pretty quick.
1989 Ranger 4X4 4 cylinder....
Ford Ranger / B-Series :: 2002 B2300 - Lower Hose That Comes Off Of Coolant Reservoir Leaking
I'm about to tear into a friends 2002 B2300 4 cyl. The lower hose that comes off of the coolant reservoir is leaking in the metal part of the line. Close to where it bolts to the block. At a glance, it looks like I have to pull the whole top of the motor apart to get it off since the line runs around behind the motor. Is there a trick to removing this coolant line without a lot of teardown? I'm not finding it at parts stores so I guess it's a stealership part.
View 2 RepliesFord Ranger / B-Series :: Water Temp Sensor Leaking / Missing Vacuum Hose
Was fixing leaking water temp sensor today and noticed the nipple under oil fill cap didn't have hose on it. After further investigation I found open spot on air intake hose with nothing in it. Both places seem to have vacuum, what goes here. BTW it is a 1999 Ranger ext cab with 3.0 flex engine and auto trans. Will try to get picture n post also...
View 8 RepliesFord Ranger / B-Series :: 1992 V6 - Upper Radiator Hose Gets Sucked Flat When RPM Is Higher
1992 3.0L V-6 RANGER
New thermostat
New Water Pump
I noticed the other day that the Upper radiator hose gets Sucked Flat when RPM is higher than Idle BAD it completely collapses IDK how it can circulate the coolant very well in this Condition. If the hoses have ever been changed But the Upper hose Really gets sucked flat. I've seen this a few times on vehicles that have been shutdown But they have always expanded upon startup and are fine....
The Lower Looks Fairly Old and only partly collapses under higher RPM.... I am going to change the Upper hose at a Minimum as its really Bad and probably a lot older than I am thinking and really Soft. I am just wondering if the radiator could be plugged up causing some of this.. Or anything else I should check into????
Ford Ranger / B-Series :: 1998 - Code P1405 - DPFE Sensor Circuit Upstream Hose
I just bought a '98 Ranger 2.5l 2wd. After driving it for a week or so I got a P1405 Code. After a quick google search I got :
P1405 Ford - DPFE Sensor Circuit Upstream Hose
Possible Causes: - Faulty Differential Pressure Feedback Electronic (DPFE) sensor (EGR pressure sensor)
- Plugged or damaged EGR tube
- Differential Pressure Feedback Electronic (DPFE) sensor harness is open or shorted
- Differential Pressure Feedback Electronic (DPFE) sensor circuit poor electrical connection
Now, I have done my research between forums and youtube and have found this EGR system to be quite. I've gone ahead and replaced my DPEF. I took an air hose and blew out all the small lines coming into the DPEF. I still have the engine light. My next move is to get a volt meter and see if I'm getting power to the sensor.
My question is about this particular code and is it possible I need to look farther into this EGR system (EGR Valve, EGR Hose, etc.)
Ford Ranger / B-Series :: 1993 - Power Steering Or Gear Box / Return Hose Leaking Where Rubber Meets The Crimp
Either one of my power steering hoses or the gear box is leaking on my 93 Ranger. It appeared the return hose was leaking where the rubber meets the crimp. So I decided I would go ahead and change the return and pressure hose to see if it stops the leak. It was a disaster. It's 2.3L manual transmission 4x2. I got the return hose off ok. I put the wrong size wrench on the pressure hose fitting at the pump but thought it was loosening but it was rounding the nut off. So I couldn't even change that hose. I installed the new return hose and retightened the pressure hose at the gear box.
Well it was a pain getting the flare fittings of the hoses into the steering box so I could tightened the flare nut down. I finally got them tightened, I think, but then when I started the engine fluid shot out of there like a water hose. It's coming from the fittings at the gear box that I thought were tightened. I reloosened and retightened them again and still it's shooting out everywhere. There is so little room getting a wrench on the hose fittings, it was slow going. What do you need to remove in order to get a good straight shot and installing these flare nut fittings and tightening them down right? If I remove the pump will it be easier to install the hoses on the gear box? I have to remove the pump now to change the pressure hose.
Ford Ranger / B-Series :: No Power To Fuel Pump
The fuse and relay have been tested. There actually is 5 volts at the fuel pump. The truck was running OK when the clutch went out. It wouldn't start after the clutch was replaced. The inertia switch is OK. I don't know where to look now....
View 14 RepliesFord Ranger / B-Series :: 1999 - New Fuel Pump Still Wants To Die?
Anyway just got a new fuel pump put in my 99 3.0 Ranger and now after it's warmed up from a few miles it starts to choke and almost die. No CEL comes on and I just put new Motorcraft plugs in and still the same thing. I read something about maybe cleaning EGR.?
View 13 RepliesFord Super Duty (1999-2016) :: Slow Fuel Fill Or Gas Nozzle Keeps Shutting Off
I notice the gas nozzle clicks off all the time when I am filling my truck. Normally I just hold the nozzle up more and it seems to work.
F250. Slow fuel fill or fill nozzle keeps shutting off....
[URL] .....
Ford Ranger / B-Series :: 1987 - Fuel Pump Won't Shut Off
1987, 2.9 ... I got all my wiring repaired and replaced both the intank pump and the high pressure pump, for a few days it would fire right up as soon as you hit the key but it had a miss (the pumps shut off after a second or two with the key on "RUN"). I tore the throttle body off and cleaned all the carbon out of it, when I put the throttle body back on I noticed that the engine to body ground was loose so I ran a new piece of 4ga from the intake manifold bolt to one of the master cylinder bolts.
After I did this I went to start the truck and no go, the fuel pump turns on with the key but then it wont shut back off until you turn the key off. if you try and start the truck it will crank but wont fire, after about a half hour of cycling the key and cranking it will start to put a little bit then a few tries later it will start but sounds rough when it first fires. I thought it may be a stuck injector so I ran some cleaner through the Schrader valve on the rail. Still have nothing, both pumps do run but still don't shut off after a few seconds like they should and now it wont even try to start.
Ford Ranger / B-Series :: Intermittent Fuel Pump Relay?
My '94 4.0L XLT has hesitated to start a couple times lately. Then, after sitting for a week while we were on vacation, the truck would not start at all today.
[URL]
I read about the fuel pump relay, so since I am not made of money, I decided to change that first ($16 vs. $100). After installing the new relay, the truck started! I put the old relay in the box and tossed it into the glove box.
After lunch, and some thought, i decided I wanted to put the old relay back in and see what happened. Guess what! It started with the old relay as well! I also noticed that the humming/buzzing sound the fuel pump makes when the switch is turned on was different with the new relay vs the old one. I put the new relay back in, but now I am unsure where my real problem lies. Intermittent relay, or fuel pump on its way out??
Ford Ranger / B-Series :: 1991 - No Power To Fuel Pump?
I can't get power to the fuel pump on my 91 ranger 3.0 5 speed. I just bought the truck and replaced all the relays checked all the fuses under the dash and under the hood. If I jump the relay it comes on and wont go off.
View 14 Replies