Ford Ranger / B-Series :: 1999 - P0135 O2 Sensor Heater Circuit (Bank 1 Sensor 1)
1999 Ranger 4x4 4.0 - P0135 O2 Sensor Heater Circuit (Bank 1 Sensor 1)
I have replaced the 02 Sensor, Passenger Side (Pre-Cat), with a Motorcraft DY831...
I reset the Check Engine fault codes, and took it out for a 50 mile journey... Check Engine light is back on, with the same exact code... What next?
I understand that it may be a fuse, and/or it may be a short in the wiring... Exactly how to test the wiring from the connector at the 02 Sensor all the way back to wherever I need to test?
I really need detailed directions, like wire colors, voltage required, or ohms, or whatever is included in this process...
Ford - Escape :: Dpfe Sensor Hose Blowing Off When Acceleration Occurs
I just had both manifold cats replaced and the egr valve which blew a hole thru the side of it and I replaced the hoses and the dpfe sensor due to the dealer said the 2 front cats were plugged this is what happened before cats were fixed the dpfe sensor blowing off and melting then the egr blew a hole in the side on my way to the garage and I also replace the fluid sensor for the master cylinder res because it looked broke and my brakes weren't working right either now that all this was fixed 3 days ago I drove it to the store this am 1/4 of a mile and the dpfe hose blew off again what is going on? ford says I should have the fuel pressure checked?
View 7 RepliesFord Ranger / B-Series :: Water Temp Sensor Leaking / Missing Vacuum Hose
Was fixing leaking water temp sensor today and noticed the nipple under oil fill cap didn't have hose on it. After further investigation I found open spot on air intake hose with nothing in it. Both places seem to have vacuum, what goes here. BTW it is a 1999 Ranger ext cab with 3.0 flex engine and auto trans. Will try to get picture n post also...
View 8 RepliesFord Transmission :: 1998 F250 - Code P0720 For Output Speed Sensor Circuit - No Reverse
I bought late 98 F-250, 5.4 G, 4WD. OHad to replace the steering flange because they messed up the ignition cylinder and flange. Truck didn't run for 4 years. 249K miles, no history available. Got the engine running, no DTCs. D, 3, 2, 1 barely moved the truck forward but, R hauled butt in reverse. Checked transmission fluid it was good and clean.
Came back to it a few days later it threw a P0720 (output speed sensor circuit) and I have no reverse, park feels like it wants to move, R is neutral, N is forward, D is forward, 3 is forward, 2 is forward, 1 is forward. The N is full drive. I cleared the P0720 code after it came up and it has not returned. The instrument gauges work but the odometer display is intermittent. Linkage? Fluid? Sensor? Wires?
Ford Ranger / B-Series :: O2 Sensor Heater Circuit Malfunction / Evaporative Emission Control System Detected Large Leak
I have some codes on my ranger 2000 here goes
P0141: o2 sensor heater circuit malfonction (bank 2 sensor 2 )
P0455: evaporative emission control system detected (large leak)
Now I will need to get that fixed cause I don't know where to look and what to look for ... For the leak I know there is a big crack on the plastic where the gas lid is could that be it ?
Ford F-150 - 1997-2003 :: 2001 - Got Code P0401 - Replace DPFE Sensor?
I have a p0401 generic exhaust gas recirculation flow insufficant detected code on my truck I was wondering what would be the first thing to check to get ride of this code? my truck hesitates from a stop while excelerating to several thousand rpm. should I try replacing the dpfe sensor? what does dpfe stand for? do they sell this sensor at oreilys or do you half to get this a the dealership?
View 9 RepliesFord Ranger / B-Series :: 1999 - Keeps Throwing P1401 - Replaced DPFE Thrice?
I have a 99 ranger with a 2.5L that keeps throwing the p1401 code. I have replaces the DPFE sensor 3 times (finally with the motorcraft one), the egr valve, the egr tube, EVR solenoid, DPFE Hoses, Ignition Coils and Gas Cap. I have scoured the internet trying to find an answer but it seems like people just continuously throw parts at it until the code goes away. What could cause the issue?
View 2 RepliesFord Excursion :: 2001 V8 - Code P1131 / Lack Of Upstream Heated Oxygen Sensor Switch
I have a 2001 Exrursion 5.4L V8. The code P1131 comes up and it says "Lack of upstream heated oxygen sensor switch - sensor indicates lean - bank #1". I hear it could be the sensor that is bad or there is a vacuum leak. It runs like a champ, no spitting, no sputtering, no missing, no ruff idle. What do I need to do to fix it or where do I need to start looking?
View 3 RepliesCamry :: 2004 - CEL Code For Upstream O2 Sensor / Idles Very Rough
I just bought an 04 camry 4 cylinder. It was running perfect when I got it but the moment we got home it threw a CEL. The code was for an upstream o2 sensor, however I did a resistance test and the heater circuit is fine. I did a voltage test on the blue and white wires and I got 3.3v and 2.9v. I don't remember which wire gave me which voltage at the moment. I would like to know if this data is a good thing or if it's broken. I do not have any data to go off of, and I couldn't find the factory service manual online. Its also worth mentioning that it idles very rough and the catalytic converter is giving a rotten egg smell but not all the time. When neither of these things happen the CEL goes away. I do not want to start throwing parts at it.
View 1 RepliesFord Ranger / B-Series :: 1998 - Cuts Out While Driving - Throttle Position Sensor
The Problem: When I start my Ranger it dies right away, I do this about 10 times or so (worse when it is wet or has rained) then I can finally keep it running, by hitting the gas. Once I get it running it will cut out while driving as well. The idle is normal and if fires properly, I just took it in to the shop (non-dealer) and they said it fires normal and has normal fuel pressure, and the their computer returned no error codes. Their sugestion was replace the throttle position sensor. Do you all think this part could be the cause and where is the this sensor and is it hard to replace?
View 12 RepliesFord Ranger / B-Series :: Code 157 For MAF Sensor
So here is what I got. Code 157 maf sensor below minimum voltage. Here is what the truck does. When the MAF is plugged in and I step on it, the truck surges and when it drops below 1k rpm it dies but I can start it back up. If I hold the throttle at 1k it stays alive. When I drive with the MAF unplugged it runs better no surging but it still dies. Here is what I have done. Reset codes no change, put new MAF in no change. I have traced all 4 MAF wires checked continuity from inside of plug to inside of plug.
All wires checked out good. No cuts breaks or anything. I have checked my battery, starter, and alternator ad all check out fine. I read that someone said if the corresponding transistor in the PCM took a dumb then it would cause not enough voltage to get to the plug because the transistor would dump the voltage from the battery leading to the MAF. I thought about running a direct power source from the battery to the voltage side of the MAF with a switch in the truck to just see if that would solve the issue but I don't know if that is possible or smart.
Camry :: 2006 - Check Engine Light Came On - Code P0032 For Upstream O2 Sensor
This issue pertains to a 2006 Camry LE 4-cyl.
My check engine light came on - code P0032 (upstream O2 sensor). I bought a new sensor from O'Reilly Auto Parts. After installing the new sensor, the car would jerk while accelerating. This continued to happen until roughly 30 miles or so when the engine light came back on and the jerking stopped! I re-scanned the car and it showed the same error - P0032. I then erased the code, and the jerking issue resumed.
I assumed this was caused by a faulty O2 sensor. I returned and got another one. Same issue.
Is this the result of not getting an OEM sensor from the dealer? Or is there something else I should be worried about?
Ford Ranger / B-Series :: Got Code P0162 - O2 Sensor Or MAP?
Just checked SES code and read P0162 I think. Stated rich fuel mixture bank 1 & bank 2 (3.0) Is this an O2 sensor or MAP issue?
View 8 RepliesFord Ranger / B-Series :: 2006 2.3L - Code P2195 / O2 Sensor
I have a 2006 Ranger 2.3l 4 cylinder that is have emissions problems the code the tech gave me was P2195 an I bought the o2 sensor just where it is, and the auto stores didn't have a manual for the year of my truck.
View 2 RepliesFord Ranger / B-Series :: 1998 - CEL On / Pending Code P0446
Today my Check Engine Light came on for the first time in years on my 1998 Ford Ranger. It has 363,000 miles on it. But the engine was changed about 150,000 miles ago. It's a 2.5 automatic. It runs good and has no problems until today. I was leaving a shop and when I started up the truck the Check Engine Light came on. It wasn't idling bad but when I went to take off it wouldn't hardly move. I wasn't even able to keep driving. So I stopped and turned it off and restarted it. Then the Check Engine Light was gone and it ran fine. I scanned it when I got home and it a Pending code of P0446.
I've never gotten this one before. It said something was wrong with the fuel vapor vent solenoid open or shorted. I've never replaced anything on the evaporative emission system except a hose under the hood 3 or 4 years ago. I've had to change the fuel pump a couple times. I've never had any wiring issues. I've never hacked into the wiring. I've owned it since it was new. Is it likely that solenoid is failing or the vapor canister is shot? I don't need this to happen again because even if it's in what was called limp mode. there's no way I could've driven it home like that. I couldn't even pull over. I was lucky I was still in a parking lot.
Ford Ranger / B-Series :: 1998 - Running Rough And Now Getting P1151 Code
1998 Ranger 4x4 4.0 Ltr - Runs rough ever now and then and CEL giving P1151 code. Upper and lower intake gaskets have been replaced.
View 14 RepliesFord Ranger / B-Series :: Code P0119 - Coolant Temp Sensor Intermittent
2001 3.0 XLT Ranger 2wd 4 door
Okay getting ready to trade in my Truck. So I removed all the extra things I put on there while I was in college, the amp, fog-lights, and analog oil pressure sensor along with their wiring. It was pretty easy minus removing the oil pressure sending unit part.
I had to unplug the MAF to move the intake out of the way while I was repairing a loose vacuum tank. But I forgot to plug it back in when i closed everything up. I started the truck and drive it about a half mile before I was able to pull over and plug it back in. Truck ran and shifted fine after that, but the CEL came on. P0119 Coolant Temp Signal Intermittent. Guy at Autozone said it was Intake Air Temp Sensor intermittent and I could just replace the part, but they were showing a separate part even though it is built into our MAFs.
So now the CEL is on, can get it to go away. Truck is a little jerky every once in a while, like a misfire, when between 50 and 60. Before all this the CEL was off. Now after I cleaned it up and removed some of the superfluous accessories, I get a CEL. I wanted to trade it in this coming weekend without having to take a loss because of the CEL or spend more money to fix it.
Ford Ranger / B-Series :: MIL P1444 Code - Faulty Purge Flow Sensor
So I had a post up saying "is MIL P1444 a urgent fix" and I got "no". On an other website though it said that it was an urgent fix. They said it was "similar to running a bad catalytic converter. You don't want to do it."
P1444:
Possible causes
- Faulty Purge Flow Sensor
- Purge Flow Sensor harness is open or shorted
- Purge Flow Sensor circuit poor electrical connection
So I located the purge flow sensor and look at the tube that connects to that,the canp solenoid, and the carbon canister. Nothing looks bad, but I did notice that the tube that connects to the carbon canister to the solenoid is not connected. The part that connects to the carbon canister dry rotted off. So I turned on my car to see if anything was coming out of that tube or air and there was nothing (not sure if that's good or bad). Also a week ago when I filled up my gas tank (before the check engine light was on) a lot of fumes were coming out of the tank while pumping.
The scanner i use also lists the secondary air system, the EVAP system, Heated catalyst, and the AC refrigenant has red X's, but they weren't continuous.
Ford Ranger / B-Series :: 2003 - Code P0708 For Transmission Range Sensor
Got a code of p0708 on 2003 ranger flex-fuel 3.0.. Which is I believe is Transmission Range (TR) sensor. Not sure where to find that on truck...
View 1 Replies