Ford Ranger / B-Series :: 2008 B2300 With Fault Code P1633

I have 2008 mazda B2300 pickup with P1633 fault code. Is this a mazda code (battery overcharge) or ford code (KAM voltage low) since it's a re-badged ranger? Alternator output measured at battery is 14.4 vdc.

View 8 Replies

Ford Ranger / B-Series :: 1994 B2300 ECU Relay Intermittently Does Not Come On

Ok I have 94 B2300 and about every 3rd or 4th start the ECU relay will not come on / energize which the the fuel pump relay doesn't come on either to prime the fuel system... so no start! It's very intermittent and sometimes the only way I can get the truck started is by pulling out the ECU relay and plugging it back in even sometimes that doesn't work too. Is it a bad relay or bad base the relay plugs into or is the ECU/computer going bad or is there wiring messed up in my ignition switch? Is there a known problem like this with these trucks?

View 7 Replies

Ford Ranger / B-Series :: 1996 B2300 - Ignition Stuck In On Position

Took my 96 B2300 2WD SE (190k) to lunch. When I went to start it back up afterwards, the key turned but no starter engaged. All the dash lights came on, and now stay on. With the key in, I can turn the ignition freely...no clicking to different positions.

It springs a little when I turn it all the way, but still no starter. When I remove the key, the dash lights stay on, etc. So, since it was on, we were able to push-start it. I've parked it on a hill for now, and will disconnect the battery when I get it home.

View 6 Replies

Ford Ranger / B-Series :: Mazda B2300 Turns Over But Doesn't Start

Mazda B2300 2.3L 1995 model... About a week ago I ran my B2300 out of gas (or so I was convinced I was out of gas) because the engine quit running. After adding gas was unable to start it back up. It turns over but doesn't start.

Here's what we did to try and fix it:

1.) Replaced Fuel Filter
2.) Check the fuel pressure, and it was at 35 psi when the key was on
3.) Replaced all 8 spark plugs (4 cylinder truck btw)
4.) Checked spark of all 8 coil pack slots and 1st and 3rd slots (exhaust side) were not sparking. After replacing coil pack we received spark but truck still didn't start.

We're speculating on the possibility of it being the PCM (ECC).

View 2 Replies

Ford Ranger / B-Series :: 1994 B2300 - Gas Gauge Reads Empty?

Any known problems with '94 Ranger/B2300 gas gauges? I just got a '94 B2300, and gas gauge reads empty with the key ON, and about 1/4 tank with the key OFF. Was told by previous owner it occasionally works, but I've never seen it work. Am starting to procure manuals and dig around the truck myself, but don't want to re-solve the problem if it's a known one. Haven't seen mention on the net of it being a recurring problem, but just starting to dig.

View 6 Replies

Ford Ranger / B-Series :: 1994 B2300 - Grinding When Downshift To 4th / Stuck In 1st Gear

I bought the 94 B2300 from a guy that said he got it from an auction and didn't know much bout it. Got 30 mins down the road and went to down shift to 4th coming into town and all I got was grinding. Turned it off and it would go into other gears and start in gear with the clutch pushed in. Wen I tried to take off it wouldn't move and just died. Towed it home and installed a new clutch kit in it. Got the clutch bled and went to test drive it and now it is stuck in 1st gear. Can it be easily fixed or am I going to have to replace the transmission...

View 3 Replies

Ford Ranger / B-Series :: 2.3L Mazda B2300 Died And Wouldn't Start Back Up

I am working on a 96 Mazda b2300 auto 2wd for a friend. His son was driving it when a loud noise, it died and wouldn't start back up. He had it towed to my house, I started to tear into to it and found it slipped the timing belt. So a rebuilt head, gaskets, timing belt, fuel injectors, water pump, thermostat, plugs, and fluids; tried to start it and nothing. Started troubleshooting and found the primary coil pack was out of spec, replaced and still nothing.

Changed out the CKPS still nothing? I have spark, I have fuel, I'm going to check compression tomorrow but the way the cylinders and pistons looked I don't think that is the issue but I going to check anyway, rechecked the timing marks they all lined up. Checked the fuel inertia switch not tripped. Could the PCM, or ICM cause a no start, and still be able to get spark and fuel?

View 2 Replies

Ford Ranger / B-Series :: 2002 B2300 - Lower Hose That Comes Off Of Coolant Reservoir Leaking

I'm about to tear into a friends 2002 B2300 4 cyl. The lower hose that comes off of the coolant reservoir is leaking in the metal part of the line. Close to where it bolts to the block. At a glance, it looks like I have to pull the whole top of the motor apart to get it off since the line runs around behind the motor. Is there a trick to removing this coolant line without a lot of teardown? I'm not finding it at parts stores so I guess it's a stealership part.

View 2 Replies

Ford Ranger / B-Series :: 1997 - CEL With Code P0133?

I have a 1997 Ford Ranger with a 4.0L 2WD. The check engine light just turned on with a code of p0133. I know that this is something with the bank 1 sensor 1. I tried doing some research and I think that it is on the passenger side before the cat converter. Now, I don't know what to do from there. How do I go about fixing this? What part do I need? How do I fix it?

View 1 Replies

Ford F-150 - 1997-2003 :: Check Engine Light Came On - Error Code P0420

I was driving along today and my Check Engine light came on. I stopped at the nearest Advance Auto to have them pull the code and it came up with the P0420, Catalyst Efficiency Below Threshold (Bank 1). I asked what could cause this and they mentioned that the fuel that was put in could be causing it. They didn't mention any other possible causes. Any others? I'm thinking it could be the fuel because the last gas station that I stopped at and filled up at is one that I never go to, and maybe just got a bad batch of fuel.

View 14 Replies

Ford Ranger / B-Series :: Code 157 For MAF Sensor

So here is what I got. Code 157 maf sensor below minimum voltage. Here is what the truck does. When the MAF is plugged in and I step on it, the truck surges and when it drops below 1k rpm it dies but I can start it back up. If I hold the throttle at 1k it stays alive. When I drive with the MAF unplugged it runs better no surging but it still dies. Here is what I have done. Reset codes no change, put new MAF in no change. I have traced all 4 MAF wires checked continuity from inside of plug to inside of plug.

All wires checked out good. No cuts breaks or anything. I have checked my battery, starter, and alternator ad all check out fine. I read that someone said if the corresponding transistor in the PCM took a dumb then it would cause not enough voltage to get to the plug because the transistor would dump the voltage from the battery leading to the MAF. I thought about running a direct power source from the battery to the voltage side of the MAF with a switch in the truck to just see if that would solve the issue but I don't know if that is possible or smart.

View 7 Replies

Ford Ranger / B-Series :: 2001 - Airbag Code 29

What airbag code 29 on a 2001 ranger means? I have not seen that number on any code lists. I triple checked the code and it is 29.

View 9 Replies

Ford Ranger / B-Series :: Got Code P0162 - O2 Sensor Or MAP?

Just checked SES code and read P0162 I think. Stated rich fuel mixture bank 1 & bank 2 (3.0) Is this an O2 sensor or MAP issue?

View 8 Replies

Ford Ranger / B-Series :: 1995 - CEL Came On - P0340 Code - CPS Bad

I am having an engine issue with my 1995 Ranger with a 2.3L. I have been having a P0340 code that kept appearing after several attempts at resetting the PCM. I gave up and took it to a Ford dealer for diagnostics and they called the CPS bad. They changed it, but the CEL light immediately came on with the code still kept coming up. The service rep. showed me the old sensor, it had a spot on the head of it where it looked like something was rubbing it. I'm assuming it's slightly rubbing on the gear it points to, which is the oil pump gear, correct? The truck runs fine, no performance issues whatsoever. Is it possible my oil pump shaft has developed play in it's shaft, causing this?

View 1 Replies

Ford Ranger / B-Series :: Getting Code Pesky P1443 With CEL?

I've been getting this code for a while. Changed the Purge solenoid and valve, replaced the hose from the canister to the two units, didn't change the hose to the intake.

Is there anything else to check? Could it be a bad gas cap? the one on the truck is a replacement.

View 3 Replies

Ford Ranger / B-Series :: 1994 - How To Check Code For CEL

1994 Ranger xtra cab
4x4
v6 4.0
5-speed
113K miles

Just bought this truck. When I test drove it no "check engine" light came on, but after purchase driving home is came on and then off many times. It only comes on at high rpm/speed. I have my trusty ODBII scanner but realize that this 1994 was pre-ODBII. How can I figure out what the CEL is about?

View 3 Replies

Ford Ranger / B-Series :: 1997 - Possible 4.0 To 5.0 Conversion?

I recently purchased a 1997 Ford Ranger with a blown 4.0 with a 5 speed , I have a 5.0 with a Carb and 5 speed out of a 80s mustang . Is it possible to use this in the 97 Ranger , I understand I need a different fuel pump but motor mount wise I was hoping it would fit.

View 2 Replies

Ford Ranger / B-Series :: 1997 - Won't Go Into Park?

Went to work one day and went to put my truck in park and it went as far as reverse. It has alot of play in the shifter. I have had a couple of people look at it and said that they would not touch it because of the air bag. I am not afraid to work on it myself if I just knew what to do. I am a single mom and on a budget, I would rather do it myself.

View 6 Replies

Ford Ranger / B-Series :: 1997 4X4 SXT - 4 Lo Won't Engage

97 automatic 4x4 SXT 4.0L. 4Hi will engage, but when I shift to neutral, press foot on brake, and shift to 4lo, nothing happens. No light, no sound. Occasionally it will make a sound, and even more rarely will light up, but it does not feel like 4Lo is engaged even when indication says it is. I pulled the shift motor and replaced, as well as verified that the transfer case could be shifted to 4 hi and lo by using an adjustable wrench. I have not put truck on stands yet, but I'm pretty sure 4 hi is truly engaging. I did attempt to engage with shift motor connected electrically but not mechanically, and it shifted. What is keeping 4 Lo from shifting? If it's a vacuum issue, wouldn't 4 hi not shift? I did check the vacuum lines and the vacuum reservoir and they seemed to be okay.

View 3 Replies