Ford Ranger / B-Series :: 2003 - Engine Knock On Cold Start
Specs: 2003 Ranger Edge / 3.0 V6 / 5-speed 4WD / 238,000 miles
Yesterday my truck was in the shop for repair. Intake gasket, Transmission fluid change, all heater hoses, thermostat, serp belt and coolant flush. When I picked it up from the shop, which was after closing, I noticed a knocking on start up. From past experience on a different truck, it sounds like a cam that isn't oiling. After a few minutes the knock goes away. I drove for a few miles, turned off the engine and started it back up and no knock this time. This morning I started it, knock was back but went away after a few minutes. Oil was changed about 1500 miles ago. Running pennzoil 5/20 with a K&N filter. Up until yesterday the engine has been completely quiet. Was wonder if something may have clogged the filter or the drain back valve.
Ford Ranger / B-Series :: Truck At Times Cranks But Does Not Start - Hot Or Cold
Removing fuel injectors-coolant contamination.. How is this done? I need to see if they are any good-or clean/replace them-after I accidentally left the clip off the hose running out of the thermostat housing when I drained my coolant last week and the first time I drove, coolant leaked onto the top of the engine/manifold depressions, getting onto and into the fuel injectors.
I tried to clean it up as much as possible the first time(finally got it going) but still a few days later the truck at times cranks but does not start-hot or cold. I assume my idiocy is the cause or maybe it is just coincidence of something else? From what I read from my symptoms it could also be the fuel pump relay, pressure regulator, coolant temp sensor, crank sensor.. among other things. My fuel pump is 1.5 years old, so hopefully that isnt it. Have the injectors possibly been contaminated to where I should just replace them?
Ford Ranger / B-Series :: 1990 Truck Won't / Hard Start When Cold
My 1990 4.0 refuses to start when the air temperature outside is at approx 40 degrees or below. It will crank until the battery runs dead if I let it. At approx 50 degrees farenheit the truck takes forever to start and always backfires out of the tailpipe and intake manifold (blowing off a hose on the vacuum tree) before it starts. If I can get it to backfire, it will start eventually. If it does not backfire, then I can run the battery dead and the truck still refuses to start. This condition has grown from a little problem to a huge problem over the past 6 months. Here is what I have done so far, including regular maintenance items.......
KOEO test checked OK
KOER test returned code 77 multiple times (TPS).
Replaced Throttle pos. sensor
Replace Idle air bypass valve
Subsequent KOER test came back with no more codes except 11 - OK
Load tested battery
Made new heavy gauge battery cables for + and -
New plugs, wires
newer starter
Changed coil pack for known good one off my explorer
Visually inspected hoses for vacuum leaks, replaced 1 cracked hose
1990 Ranger ext cab 4X2 4.0L, K&N air filter in stock airbox, Pacesetter headers, single 2 1/2" exhaust, stock cat no muffler, 260K on truck, 104K on good used engine from my 1994 Explorer. Purchased Ranger brand new in 1990. A4LD w/ shift kit.
Ford Ranger / B-Series :: 2003 - A/C Start Working Properly And Blowing Cold Air
I have an 03 Ford Ranger 4x4. Great truck and runs great just with one small problem. For whatever reason, every single time, the a/c only blows un-cool air (not hot) when I start the truck. Then, and only then, after about 30-40 mins of constant driving around does the a/c start working properly and blowing COLD air. After that it works great but it always takes about 30 mins after I start the truck for it to work correctly.
View 4 RepliesFord Ranger / B-Series :: Truck Won't Start In Cold / Security System Light Comes On
We have a 2007 Ranger. When the temps hit 32 degrees F or below, the truck won't start. The security system light comes on. We have to run through the security system reset process, sometimes a few times, before it will start. Afraid all this key turning is going to burn out the ignition. Don't have a lot of confidence in my Ford dealer as they replaced the brakes and put the shims in wrong. Local mechanic says it's probably electrical. Is there anyway to bypass the security system or can it be removed?
View 1 RepliesFord Ranger / B-Series :: Shaking Really Bad When Get To 35 MPH
I have a 1994 ford ranger 4x4 that I just put on and 35's and when I get to 35 mph it shakes really bad. What the problem is. Have been told that I need a steering stabilizer.
View 9 RepliesFord Ranger / B-Series :: 1999 - Shaking When At Idle In Gear
I just got a 99 2.5 rwd auto and it shakes when it's at idle in gear. I'm pretty sure its because the AC pulley is engaging drawing power. I was thinking about turning the idle screw up a blonde-one because when I hold the brake and give it slight gas it goes away.
View 3 RepliesFord Ranger / B-Series :: 1986 - Power Steering Shaking Then Spinning On Itself To Hard Left?
My 40 Ford pickup is on an 86 Ranger chassis and uses the stock Ranger steering gear. My question is about the connections on the steering box. I'm using a GM power steering pump and several steering gear vendors have told me that outside of needing to adjust the pressure for the correct feel, the combo works. I fired the truck for the first time tonight but the steering wheel went crazy, shaking around and finally spinning on it's own to a hard left.
Some quick research leads me to believe that I have the lines reversed but it would be great to know for sure. I did manage to find on e diagram of a Ford PS box on Google and it shows the lines reversed of what I have set up on my truck and I can't for the life of me remember how I figured out what the plumbing should be when I installed it. Which port on the box is the inlet and which is the return?
Ford Ranger / B-Series :: 2003 - Valve Cover Leak / Exhaust Smell Then Started Bogging / Dying And Shaking
I have a 2003 ford ranger 2.3 vin d 5 speed, this truck originally... Took it in for wires plugs front brakes fuel filter battery and added a small cold air intake. We discovered a valve cover leak and while repairing guy drops a screw into a valve and when finished he started it lodged the screw between the valve, shearing off a cam sprocket bolt. Throwing the timing. 2 valves on the exhaust side were bent and replaced. no damage to the head.
Timing was reset and the truck was running. 2 days later truck is running/had a hint of exhaust smell then started bogging dying and shaking, at which time we got an 02 bank2 lean code and fixed that. it cleared code and didn't fix it. From there we replaced coil, imrc intake bc of a crack, tried and check all vacuum, reset the timing. Timing would slip before but no longer than 10 minutes every time truck started.
Found the hole in the timing cover that holds the bolt to torque? to harmonic balancer was broke. replaced along with the diamond washers and cam sprocket bolts. timing finally held crank sensor was adjusted. truck came home for one day running good, we had removed the cold air intake and replaced the factory air intake. next day it was so slow outta first gear, you must baby the throttle, if you floor It, it sputters and kinda pops, truck stays slow all the way to about 10 mph and 2000rpm then it begins grabbing speed, 3000rpm is where this truck shifts the best, 2nd is better, third better than that.
As rpm increase the truck runs better, it idles steady at 1100-1200rpm at stops with an audible miss and then struggles again on takeoff. Here what im wondering, the truck has an abs sensor that just came on, but no codes showing now.tomorrow I wil run matko determinator 3.0 on it. and test the catalytic converter. first how do I check the timing belt to see if it stretched? do these trucks store the p.i.d.s. koer or kams that could cause one, all, or any of this and if so do I have to have it flashed from ford or can you manually do this without a drive cycle test.
Ford Ranger / B-Series :: 1998 - Rough Idle At Cold?
I understand there is not much adjustable on my 98 Ranger (2.5L) as far as idle speed and mixture. It runs rough when started cold. Is this a sign to replace spark plugs?
View 2 RepliesFord Ranger / B-Series :: 1998 - No Heat Only Cold Temp?
98 ford Ranger 2.5L.
I have not heat from the vents, doesn't get warm at all. If I idle the enginer in 30 Degree weather it gets to almost the C.
Upper Radiator hose is hot, I have verified the thermostat is new and it opens at 192 degrees as it should. Replaced the Water Pump, Fan spins freely.
I have attempted to burp the system, it isn't kicking out anymore air from the lines that I can tell. I used a large funnel and filled it with Anti-freeze, it filled the radiator, burped the system and the reservoir filled to overflowing. All with the engine hot. (To be specific the funnel was always full of fluid so no air could get sucked backwards)
The heater core hose on the left when looking from the front of the vehicle does not get hot, the one on the right gets warm. I theorize that the heater core is clogged up somehow and that is why that left line doesn't get hot. There is no fluid in the cab of the truck from the core.
Ford Ranger / B-Series :: 1996 - Transmission Slipping When Cold
I have a 1996 Ford Ranger with 95k miles on it. Recently, my truck's automatic transmission has been slipping really bad. I'll be driving down my road and while going around a turn, the clutch feels like it randomly disengages, so when I press on the gas, it feels like I'm revving my truck in neutral, and then it will all of a sudden get back into gear, violently a lot of the time. However, once the truck is warmed up, the it runs perfectly and never slips. I've checked my oil multiple times and even changed the oil filter in the transmission. I am not sure if this has anything to do with it, but if I let my truck idle in park for a little bit, the RPMs will increase and if I shift in to reverse or drive while the RPMs are high, it'll do the same thing.
View 14 RepliesFord Ranger / B-Series :: 2011 - Installing Cold Air Intake?
I would like to install a cold air intake in my 2011 Ford Ranger. What brand should I go for? Volant or K&N?
View 4 RepliesFord Ranger / B-Series :: 1989 - Engine Sluggish When Cold
I have an 89 Ranger 2.3l with 255,000 miles on original engine. The engine runs like brand new. I'm just curious as to why it's extremely sluggish when cold. Example, it was 3 degrees this morning and I literally couldn't get over 45 mph for 5-10 mins. Everyone was passing me. No knocks or other strange noises just doesn't have any power. Once warmed up its completely normal. Obviously my '01 4.0 Ranger doesn't do this so I was mainly interested in why? Do they use different metal materials, is engine wore out (obviously it is to an extent), or something else?
View 2 RepliesFord Ranger / B-Series :: Ice Cold Air Goes Away Whenever Slow Down To Turn Or Accelerate
Whenever I slow down for a car to turn or accelerate after a stop sign the ice cold air goes away and is replaced by warmer air but then it never turns back cold. Only when I kill the engine and start back up does it return. I just had the Freon refilled and there are no leaks.
View 3 RepliesFord Ranger / B-Series :: 1992 - Fuel Pump Does Not Work When It Is Cold Outside
I have inherited a 1992 Ford Ranger 4.0 with an unusual problem. When the temp drops outside the truck will not crank. The relay is coming on for a sec or 2 to bring the system up to pressure but the pump never turns on. This happens every time the outside temp drops below 60. I can wait until later in the day or until a warm day, hit the key and drive it till it runs out of gas. A week later (and another cold front) and it is sitting dead in the front yard. I have traced the grounds, checked the power thru the relay (and replaced the relay too), but it still does this. What I want to know is am I the only one to ever run into this and if not then what is causing it. Pump shows no sings of trouble on a 70 degree day, even runs the proper pressure and volumes. I am stumped at this point and I am ready to try replacing the pump (though the one in it looks brand new). comments?
View 11 RepliesFord Ranger / B-Series :: 1998 - Missing On One Cylinder During Cold Startup
1998 4.0 ... She only misses about 30 seconds during stone cold startup. I figure it's probably the plug thats hardest to reach ? Isn't that the way it always is? From the hood I can see only one spark plug, so I figure I'll do all the plugs. Is there any right or wrong approach to the plugs? I did the thermostat today, but this plug job looks like it's gonna be a bitch. Time for some skinned knuckles Next is the right side O2 sensor, that looks like fun too. But I gotta say, this little truck is sweet. Great visibility and easy to park in the city. I really like her. She's a keeper. She needs some new sway bar bushings too, but no surprise with 127 K on the clock.
View 5 RepliesFord Ranger / B-Series :: Temperature Gauge Not Raising Stays At Cold
I have a 2001 ford ranger xlt 2.3L and the temperature gauge has been staying a cold. And my heat doesnt heat well. I'm guessing I need to replace the thermostat. Before I do that could it be anything else?
View 9 RepliesFord Ranger / B-Series :: 1994 2WD - Temp Gauge Is Staying On The Cold
My 94 Ranger 3.0L 5speed 2wd temp gauge is staying on the cold side but the heater is working good and I used a laser pointing thermometer at the thermostat housing and got 180* after running for a while and I also noticed that the fuel economy had gone down along with the power. I was getting 340 miles to a tank but now I'm getting 280 per tank.
View 12 Replies