Passat (B5) :: Temp Gauge Staying Pinned At Cold
Alright so noticed the other day that my temp gauge was staying pinned at cold. every once in a while it will jump up to the normal range but not for more than a few seconds to a minute before it drops back to cold. I just bought the car so I've still got a warranty from the dealer and im fairly convinced that I don't have to bee too concerned with it over heating because when the gauge DOES register its saying normal. just thought id ask here before i drive the 2 hours back to where i bought the car.
View 11 RepliesFord Ranger / B-Series :: 1994 V6 - Oil Pressure Gauge Does Not Work
My oil pressure gauge does not work. I was told that it's most likely the sensor. Where would I find this to change it out?
View 3 RepliesFord Ranger / B-Series :: Temp Gauge Hardly Moves At All
I have a 94 Ford Ranger, 2WD, 5-Speed, with 2.3 engine. My temp gauge hardly moves at all... It actually appears as if it doesn't move it you don't pay close attention and were to just glance at it. I'm thinking it is most likely the temp sensor that is on the engine block as I understand there is also one that is in the line that controls the fans for the radiator. Am I approaching this in the right direction or is there something else I might need to do?
View 3 RepliesFord Ranger / B-Series :: 1994 B2300 - Gas Gauge Reads Empty?
Any known problems with '94 Ranger/B2300 gas gauges? I just got a '94 B2300, and gas gauge reads empty with the key ON, and about 1/4 tank with the key OFF. Was told by previous owner it occasionally works, but I've never seen it work. Am starting to procure manuals and dig around the truck myself, but don't want to re-solve the problem if it's a known one. Haven't seen mention on the net of it being a recurring problem, but just starting to dig.
View 6 RepliesFord Ranger / B-Series :: 1997 - Water Temp Gauge Does Not Work
Water temperature gauge doesn't work. Assumed the problem was the sensor so bought a new one. Installed it, still nothing registering on the gauge after I know the water is heated up (drove it for 45 minutes, heater blowing hot).
So crossed the ground on the sensor and the gauge shot to the top so gauge is working.
Pulled wiring diagram and that sensor is SUPPOSED to register 79ohms for cold and 8 ohms for hot.. So bought a 10ohm resistor from radio shack and attached the water temp lead to it and the gauge read correctly about 1/8 inch from the H mark on gauge. This confirmed for me that gauge is not at fault.
Next I attached the ohmmeter to the sensor itself, boiled some water, placed the sensor tip into it and it read 86 ohms, in freshly boiled water! So at boiling the sensor isn't anywhere near to tripping the gauge to even start reading cold! So I tested the old sensor that I was replacing and in boiling water it shows 94 ohms?
What am I doing wrong, is there an assumption I am making here in error? I want to conclude the new sensor is bad, but the old sensor reads nearly the same reading under same conditions.So yes maybe they are BOTH bad but that seems to be pushing probability.
If it matters this sensor is the type that is inline from radiator to heater core, not the type that is in the engine block, at some point ford changed their sensor setup but didn't change the schematic drawing. Which doesn't matter the only difference is the one in-line has a ground wire to it rather then grounding off the engine block.
Vehicle is a 97 Ford Ranger with the 2.0 liter engine.
Ford Ranger / B-Series :: 1998 - No Heat Only Cold Temp?
98 ford Ranger 2.5L.
I have not heat from the vents, doesn't get warm at all. If I idle the enginer in 30 Degree weather it gets to almost the C.
Upper Radiator hose is hot, I have verified the thermostat is new and it opens at 192 degrees as it should. Replaced the Water Pump, Fan spins freely.
I have attempted to burp the system, it isn't kicking out anymore air from the lines that I can tell. I used a large funnel and filled it with Anti-freeze, it filled the radiator, burped the system and the reservoir filled to overflowing. All with the engine hot. (To be specific the funnel was always full of fluid so no air could get sucked backwards)
The heater core hose on the left when looking from the front of the vehicle does not get hot, the one on the right gets warm. I theorize that the heater core is clogged up somehow and that is why that left line doesn't get hot. There is no fluid in the cab of the truck from the core.
Ford Ranger / B-Series :: 1994 - Idles Rough / Stalls When Cold But Runs Great When Warm
I have a huge problem. My 94 ranger 2.3L 5 speed manual transmission, has problems with idoling while it's cold, has no power going uphill and stalls when I slow down to stop. This is all after putting a new motor in. The old one was running ok with 310,000 but lagging bad. I figured with the driving I do, a new motor wouldn't be a bad thing. Boy, was I wrong. It has been a nightmare. But once the truck is up to operating temperature, it runs so smooth you wouldn't think there was a problem. But let it cool off, restart, and boom! There it is. We have changed so many parts and sensors with absolutely no change to the original problem. It's very frustrating. I just can't let this problem win. I will figure it out.
View 13 RepliesFord Ranger / B-Series :: Temperature Gauge Not Raising Stays At Cold
I have a 2001 ford ranger xlt 2.3L and the temperature gauge has been staying a cold. And my heat doesnt heat well. I'm guessing I need to replace the thermostat. Before I do that could it be anything else?
View 9 RepliesFord Transmission :: 2002 - Temp Gauge Move To Running Temp In Cold?
02 6.8 4x4 excursion. When I start the truck cold, the trans temp gauge immediately moves to "running" temp. Not really sure how this happens, I'd figure that if the xducer was trash it would ride all the way high or all the way low. What's happening here? I'd sure like a functional gauge...
View 6 RepliesFord Aerostar :: 1994 - Temp Gauge Reading Low?
It is a garage queen 1994 4.0 AWD with 42,000 miles in nearly perfect shape. Except for the dent in the rear on the passenger side.
I have posted a picture of the dash when going down the road. As you see the engine light is on. It comes on intermittently, pulled the codes, indicated MAF, 02 sensor, running lean/rich. Runs like a champ, no hesitation, still gets up and goes, gets the appropriate gas mileage. I replaced the 02 sensor with the original Ford Part. Didn't cause the engine light to stop going on after about 20 to 60 minutes driving, sometimes it doesn't come on at all.
Could this thermostat be running too cool and causing the engine to throw those codes? Would gladly take it to a mechanic, but seems like it might be a fishing trip with my dollars for them. Next I was going to replace the MAS myself, easily done with the original remanufactured part at a cost of 150.00, 70 for the core, but don't want to chase my tail with these engine lights on when it runs nearly perfect.
Have sprayed the MAF. Checked for air leaks anywhere. Done all the things I could do by just lifting the hood.
So the picture shows the Temp gauge barely touching the N flying down the road at 70 on a level surface, outside temp about 60. Reading the posts says they all run in the cool section of the temp gauge.
So the question is, do they run this cool? Heater works fine and the gauge goes up past the N resting before the O when going up hills on the way to Tahoe. Is this a thermostat problem on a 20 year vehicle with low mileage, or am I going to have to bite the bullet and let the mechanic go wandering through the vehicle?
Ford Ranger / B-Series :: 1999 - Got Code P0455 - CEL Staying On?
99 2.5L. P0455. I'll just be driving and the CEL will come on and stay on. I pull the code and get a P0455. Gas cap is brand new and I can wipe the code and it will come back a few days later.
View 2 RepliesFord Ranger / B-Series :: 1990 - Check Engine Light Staying On
1990 ford ranger.. I just bought this truck, check engine light stays on.. What can I do to find out what's the problem?
View 3 RepliesFord Ranger / B-Series :: 1997 - Dome And Door Ajar Lights Staying On
The dome light and door ajar light on my 97 Ranger stay on. The switches are good, is there a relay or other device in the circuit?
View 9 RepliesFord - Ranger :: 1994 - Battery Is Not Charging And The Temp / Oil Gauges Spike
While driving at any speed my temp gauge and oil pressure gauge spike well above "H" and stay there. The red battery light sometimes flickers too. The Battery gauge is low. I replaced the terminal to then negative battery cable because It was loose. I have also replaces the alternator. I had the battery checked and it was good, it just at 45% charge. That's why I replaced the alternator. After I did that, It seemed to have fixed the issue. But after 3 days, it has come back again. Now this morning on the way to work, driving down the freeway, my speedometer jumped to 85 MPH and there was a squealing like noise coming from the engine. I am not sure if the two are related issues.
View 10 RepliesCamry :: 1994 - Overheated Engine / Temp Maxed Out The Gauge And Coolant Was Gone
My radiator gave way on the highway, and by the time I noticed it the temp had maxed out the gauge and all the coolent was gone. So, I only have 90k on my '94 Camry and I'm debating whether to tackle repairs and perhaps a rebuild if necessary. What's the likelihood that there's damage to the rings, bore, crank, valves, etc due to the overheat? How much repair am I potentially looking at and what can I check without a tear-down? I'd like to get it running again since I just invested in new struts, brake calipers and MS and tires (not to mention that it has been pretty-much worry-free until now), but I want to know whether it's even worth my while.
View 6 RepliesFord Ranger / B-Series :: 1994 - Jerking Below 3k RPM?
My 94 ranger, 3.0 v6 began to sputter and jerk about a month ago. It does this when ever give more then lite throttle up until about 3000 rpm. I have replaced plugs, wires, coil and cleaned the air flow sensor. I feel like this has worked a little but the problem is still definitely present. When I hit 3k rpm if feels lie the truck begins to run correctly and almost like it had a power ban much like a dirtbike, but again it's just the truck running correct.. And above 3k rpm it runs great... and every so often the problem will completely disappear for 5 minutes or so, then come right back.
View 1 RepliesFord Ranger / B-Series :: 1994 - Mpg Dropped - Fix?
I have a 94 2wd 4.0 auto 3.08 rear end it has 195,000 im gettin 15 city 18 hwy I used to pull 24+ hwy I changed plugs and wires no change? It has the 4.0 tick but its always had it....
View 7 RepliesFord Ranger / B-Series :: 1994 - Got Codes 218 And 998?
Working on a friends 94 ranger, 2.3 L with codes 218 and 998. Chiltons manual does not even show this code. Code is for Loss of Ignition Diagnostic Monitor (IDM)/left side. What exactly is this? Can't find anything that explains the IDM.
998 means a hard fault.
Ford Ranger / B-Series :: 1994 - Low To No Heat
1994 ranger 3.0 .. New: water pump, htr. hoses, radiator, thermostat, pulled & flushed htr. core. (2 year time frame) ....
View 5 Replies