Ford Ranger / B-Series :: CEL On After Oil Change?
I just changed my Oil, added a FRAM filter and bought some good Quakerstate High Mileage and my truck runs good. However, I noticed that my Check Oil light is constantly on. I also recently changed my Oil Sender, and I wonder if that has got something to do with it.
View 3 RepliesFord Ranger / B-Series :: 1996 - When To Change The Timing Belt On A 2.3L
What is the recommended interval for the timing belt change? I have a '96 B2300 with ~85K on it and he original timing belt. I wanted to change the serpentine belt and my mechanic said he'll take a look at the timing belt. It's not cracked or anything but he says that after 8 years it should be changed.
View 14 RepliesFord Ranger / B-Series :: How To Change Front Rotors An Auto 4X4 Hub
Looking for a good write to change the front rotor (BIG CRACKS IN IT) on a 97 auto locking 4X4 hubs? Any special tools etc...?
View 7 RepliesFord Ranger / B-Series :: Change Shifting Points - Shift Into 5th At 45 - 50 Instead Of 55?
I have a 2002 3.0 with the 5R44E. I don't like how late it shifts into 5th gear. Is there a way to make it shift into 5th at 45-50 instead of 55? I feel like I have to let off the gas half of the time to make it shift and I don't have a heavy foot. If anything, driving with a light foot seems to make it shift into 5th later.
View 8 RepliesFord Ranger / B-Series :: 1986 2WD Not Running - Shift Linkage In Way To Change Starter?
But here's too my question. I recently bought a 2wd Ford ranger 2.9 automatic. Bought not running. They said it wouldn't turn over that there was something wrong with the starter. I figured it was the neutral safety switch turned out it was there's a wire broke on it. I can get in there touch the wires together and it'll turn over. But I can't fix it because the shifting linkage is In the way. I'm wondering how too take it off. I've never worked on one before. And I don't wanna mess up my gears.
View 1 RepliesFord Ranger / B-Series :: 2000 - No Change In Idle When Pull The Injector Plug
Its a 2000 flex fuel 3.0... Its not the actual injector. I think its wiring or computer. No change in idle when I pull the injector plug. But I think I can feel the injector opening and closing. Compared to nearby injector diagnostic light flashes less brightly. but that's pretty hard to quantify
When I pull the plug on another injector it idles about the same but I can tell it surge up and down as I disconnect and reconnect it. Fuel injectors were backflushed and swapped same problem cylinder. Where do I go from here just take apart the loom and look for abraded wires? Its the number one cylinder, passenger front.
Ford Ranger / B-Series :: 2002 - Changing Coolant Sensor?
I removed what I could, plastic cover and thermostat housing. Looks like I have to pull the intake to get the little bugger out of there. What's the procedure to remove and replace?
View 2 RepliesFord Ranger / B-Series :: 2002 V6 Slightly Over Heated - Oil In Coolant
My 2002 4.0L V6 Ranger, 4x4 overheated *slightly* this past weekend. I added some water and limped it home with a couple stops, trying not to let it get too hot. I since noticed there is oil in the coolant, so jumped to the first non mechanic's assumption the head gasket was bad. I have had (auto) tranny troubles with this truck in the past and started looking inside today and noticed some red fluid under the truck. I think the tranny fluid cools through the main radiator on this one, yes? If so, do I likely have a bad radiator, or is there another likely possibility?
The only wet areas I can find look like where the hard lines come into the right side (looking from the front) back of the rad. If we can determine that, would I need to replace the radiator, or is there any way to plug the tranny lines and run through a separate cooler? I think this also has a tranny, or oil cooler in front of the main radiator but not sure if that is correct, or what exactly that is. This is my daily driver work truck and will bring work to a stop until I can figure it out.
Ford Ranger / B-Series :: Burning Oil / Coolant In Cylinder 3 On Driver Side
I have a '90 Bronco II w/ the 2.9L V6 with a head/gasket issue leak. Its burning oil/coolant in #3 cylinder drivers side. I would ask this in the B2 section, but the Ranger section seems to have alot more activity.
I'm wondering what my options are. I'd like to replace the head with a better aftermarket design if possible. I've seen World Products mentioned as a good replacement, but they are no longer making them anymore. Nearest I cant tell, that leaves King and Odessa aka Clearwater heads. On the 'bay Odessa doesn't have the greatest feedback. King looks like a good product, but kinda spendy also. Short of those two, re-man is the only other option.
The casting # on my head doesn't line up either, is the 86TM the better Euro head for the Merkur?
If I keep this engine, w/o doing a 4.0L conversion, I'm tempted to replace both cylinder heads because of the amount of work to tear it down to that point.
This motor has had some valve ticking also, but I've read it can be injectors instead. What should I do? This will only be used as an off highway light trail rig.
Ford Ranger / B-Series :: 1991 - Bad Head Gasket - Leaking And Coolant In Oil
I have a 91 Ranger V6 4WD with 150K that has been sitting for 7 years. The last time I drove it (7 years ago) to a mechanic, who diagnosed it with a bad head gasket - leaking coolant and coolant in the oil.
What am I looking at as far as a project: besides redoing the head gasket, what else will I most likely need to do given that its been sitting 7 years?
Ford Ranger / B-Series :: 1999 - Losing Coolant Internally / No Water In The Oil
1999 3.0. Been losing coolant internally. No water in the oil. Been back and forth on doing a full engine swap (its got 250k on it). So finally decided to just try the head gaskets. Anything out of the ordinary on these? Anything to look out for? Any special tools?
View 14 RepliesFord Ranger / B-Series :: 1996 - Coolant Leak Just Above The Bell Housing
My '96 ranger, 4.0, auto transmission has developed a coolant leak. It is at the rear of the engine, passenger side, at or just above the bell housing. I can't quite see where it is leaking from even using an inspection mirror from on top or underneath. The engine runs great. I just finished replacing the power steering pump, ac compressor, dryer and hoses. What is back there? Freeze plug? Do I fear the worst and that the head or block warped? I may drill a hole from the passenger compartment to try and get a better view.
View 4 RepliesFord Ranger / B-Series :: Ammeter And Coolant Temperature Gauges Not Responding?
My ammeter & coolant temperature gauges have quit responding. Any "easy" ways to check these circuits before I disassemble the dash? And, if the gauges DO turn out to be bad, where can I get replacements?
View 4 RepliesFord Ranger / B-Series :: 1997 - Coolant Disappearing - No Leaks And No Smell
1997 Ford Ranger XLT 4x4 3.0L. So I've replaced my thermostat thinking that would fix the coolant vanishing problem, turns out it did not. Make tank became dry once again and my temp gauge keeps going back and forth from cold to hot.
View 2 RepliesFord Ranger / B-Series :: 1998 V6 - Little Bit Of Coolant On The Bottom Of Bell Housing
I changed the oil on my '98 Ranger 4.0L V6 yesterday and noticed a little bit of coolant on the bottom of the bell housing. It wasn't much (yet), but it was trickling down from above on the driver's side. I couldn't see clearly behind the engine on top without removing some stuff, but I could see where it looked like it was dripping onto the bell housing, ca.3/4 of the way up on the driver's side. Where the leak may be and how to fix it? As I said, it's only a couple drops now, but I'd like to nip it in the bud.
View 4 RepliesFord Ranger / B-Series :: 1994 - Coolant Loss / Head Gasket Leaking
I am working on my buddy's 1994 Ranger with a 2.3L I4 that has been going thru a large amount of engine coolant. The trucks has approximately 180,000 miles on it. When I had it parked on concrete I have not seen any signs of coolant on the concrete or any signs of coolant leaking. The next place I checked was inside the cab to see if there was any coolant from the heater core and there was not. The water pump has been replaced a couple of years back. I replaced the spark plugs today and did not see anything on the plugs that I would have thought were signs of coolant in the combustion chambers.
With that being said I have not worked on a vehicle with a leaking head gasket before. Would there be any visible signs on the sparks plugs? If so what would I be looking for? When standing in front of the vehicle with the engine running there is a slight smell of antifreeze being "vaporized". Are there any noted issues with this engine that would cause this? Are there any other things I should check? Could it be a leaking head gasket causing this? If so how can I check for that?
Ford Ranger / B-Series :: Code P0119 - Coolant Temp Sensor Intermittent
2001 3.0 XLT Ranger 2wd 4 door
Okay getting ready to trade in my Truck. So I removed all the extra things I put on there while I was in college, the amp, fog-lights, and analog oil pressure sensor along with their wiring. It was pretty easy minus removing the oil pressure sending unit part.
I had to unplug the MAF to move the intake out of the way while I was repairing a loose vacuum tank. But I forgot to plug it back in when i closed everything up. I started the truck and drive it about a half mile before I was able to pull over and plug it back in. Truck ran and shifted fine after that, but the CEL came on. P0119 Coolant Temp Signal Intermittent. Guy at Autozone said it was Intake Air Temp Sensor intermittent and I could just replace the part, but they were showing a separate part even though it is built into our MAFs.
So now the CEL is on, can get it to go away. Truck is a little jerky every once in a while, like a misfire, when between 50 and 60. Before all this the CEL was off. Now after I cleaned it up and removed some of the superfluous accessories, I get a CEL. I wanted to trade it in this coming weekend without having to take a loss because of the CEL or spend more money to fix it.
Ford Ranger / B-Series :: 1993 - When Engine Warms Up Coolant Overflow And Spills Out?
1993 ranger, 3.0 V6 203,000 miles. As engine warms up coolant in blown into over flow and spills out. At that point system is low and truck runs hotter than norman, 3/4 way across gage. What would be causing overflow to overfill from engine. Could it be a bad rad. cap? Just replaced head gaskets at 200,000 miles. Truck runs good. No oil in water, no sign of visible leakes other than overflow tank overfilling and loosing coolant.
View 10 RepliesFord Ranger / B-Series :: Coolant Leak From Timing Chain Cover Gasket?
I have 2000 V6 3.0 Ranger and it has sprung a small coolant leak from timing chain cover gasket. I think just few drips after driving a while since I don't see significant drop in coolant level (Took a month to notice level dropped in reservoir) and did not see an active leak while idling. No water in the oil.
The proper repair would be to replace the gasket, but for the age and condition of the truck, I don't think it is worth it. Searching for a cheaper solution, I found K-Seal and see lots of reviews with success. Will it damage the cooling system in anyway? I think it would be worth a try even if it doesn't fix the leak as long as it does not cause any harm.