Ford Ranger / B-Series :: 2004 Truck Dies / Stalls While Driving
The problem : I bought a 2004 Ranger truck and after two days it started to hiccup, or stall or die while driving, then because the truck is manual, just start up and keep running. It was the strangest thing.
I gave it to a shop, and after checking the electrical, the ignition, the fuel system, the drive train, and ten hours of troubleshooting, they came up without an answer. So they gave me the truck back.
Answer, a few days after taking it back:
I had told the shop that it had been sitting for 6 months, May till January, but when I told a mechanic friend a bit later, he still suggested 2 bottles of gas line antifreeze in the tank, before the next tank fill. I did that, and there was some improvement.
Next, When I replaced the balding tires with new Nokian Winter tires, the tire shop, (Kal Tire), told me that the air cleaner was incredibly dirty, and asked me if I would like them to replace it. I said yes, thinking that it might just do the trick, as no one in the forums I read, had mentioned it.
Success! No hiccup or stalling and it has not died since.
Ford Ranger / B-Series :: 2004 2WD - ABS Light On And Code C1186
2004 3.0 auto 2wd. ABS light (and brake light) both on solid. I got the code C1186 - ABS power relay output open circuit pulled today at oreilly. He said there were no codes for the brakes. So, where to start and could it throw both lights for the same code?
View 2 RepliesFord Ranger / B-Series :: 2004 - Anti Theft Code B1602
I have an 04 ranger with a 4.0 and got a code b1602 ....
View 1 RepliesFord Ranger / B-Series :: 2001 - CEL On / Low RPM And Stalls
My Ranger has been acting funny lately. My check engine light is on. I stopped by an Autozone and the guy read the codes - I don't remember exactly what the code was but he said I just needed to use some fuel cleaner - he recommended Seafoam. Now, I assume he was just trying to sell me something. But I've tried that, Gumout and STP in the tank with no luck.
If I'm driving and come to a stop, my RPM dips down to about 600 or lower, my truck starts shaking and will eventually stall if I don't step on the gas. This only happens with a warm engine - If I start the car up and go a mile down the road, it won't happens. But if I go 10 miles down the road, it will. I assumed I had a bad throttle position sensor so I just ordered the part and replaced it but the same behavior exists.
It's been a while since I've replaced the fuel filter - it might just be that.
Ford Ranger / B-Series :: 1999 - Stalls Out Under Load
So my 99 2.5 rcsb has been stalling out under loads, particularly when the A/C is on. It's stalled when warm, cold, engaging Drive or Reverse, and it steering does it at least once a day. There's a missing elbow to a vacuum line at the driver side (looks RABS related). The truck had the CAT melt off and now it's laying in my bed with the O2 sensor, don't know if that relates.
This truck sees 100 miles a day through the mountains, 5-7 days a week. It only has 140,000 miles on it, I put 40,000 on it in the last year with no issues. The truck is very much showing age (needs almost everything), but I'd like to keep the basics going.
Ford Ranger / B-Series :: Truck Stalls While Driving
1994 FORD RANGER stalls while driving - differant speeds ...differant miles ...no rhyme or reason to it - cranks right back up ...can even pop clutch and cut it back on. Already replaced Ignition Start Module - Dpes sensor - temp sensor - and scan shows all codes are clear and truck passes. We are clueless to whats causing this. 4 cyl 2.1
View 12 RepliesFord Ranger / B-Series :: 1987 - Stalls Out While Idling?
so I have a 1987 2.9L Ranger that likes to stall out when its idling after reaching temperature. Ive replaced all sorts of sensors (IAC, Coolant Temp, and PCV) and so far no luck. I was trying to figure out what the relearn procedure was for the IAC or get an input on any other possible sources of error. I haven't changed TPS yet.
What the engine does is when it gets up to temp, the engine will start to loose speed, and will start to shutter. Then it'll kick back up run fine for a few seconds and drop again, it'll do this for a few minutes then completely just choke out.
Ford Ranger / B-Series :: 2003 XLT Stalls When Put It Into Gear
2003. Ranger xlt with the 4.0.... So I just bought this truck and was informed that the vacuum might not be functioning correctly. And here's the symptoms. It idles a little rough, nothing major. When I put the truck into gear either drive or reverse, it stalls out almost every time unless I give it some gas and hold the brake. But after that I could drive it all day with out a problem, as long as I don't put it into park. And last it starts a little hard. But the damn thing runs great while driving it. It's still very snappy even having high miles.
View 4 RepliesFord Ranger / B-Series :: 2003 - Stalls / Shutters On Acceleration
My 2003 ranger, 4.0l, 5 spd manual with 295K miles has no power on acceleration. Engine shutters/stalls. The following have been replaced in last 20k miles; fuel pump, plugs/wires, mass flow sensor and fuel filter. Last week left for work and could not go faster than 50 mph. Condition has gotten worse (barely goes past 40 mph).
Changed filter with no improvement.
Checked fuel pressure - constant at 65 psi.
Changed coil - no change.
The tank of gas I put in just before problem was from station with tanker dumping while I pumped. That tank is out of truck; filled from different station. Also put can of seafoam in tank. No change.
Ford Ranger / B-Series :: 1998 - Battery Died Now Stalls?
98 Mazda B4000 4.0 4x4
I bought this truck about two months ago and it has been great no problems starts right up and runs like a top. I was installing a 4 channel amp yesterday on and off and the dome light was on all day as the doors would periodically be opened or closed so it never did that cycle of 10 min or whatever when the lights turns off. This is what killed the battery.
I had my neighbor jump me and after a few minutes of charging it started right up and idled for about a minute long enough he left and parked, then it stalled. I started it about another 6 times before the battery died again. Every time it started fine then would idle between 1-10 sec then start to sputter and eventually die. Pressing the accelerator pedal only killed it faster.
I got a new battery today as the other charges so that I could fix it today without missing work again tomorrow. Unfortunately it does the same thing I was hoping that the voltage was just low or the polarity flipped or something on the other battery.
To sum it up the truck never gave previous symptoms just simply ran too low (battery never DIED the lights came on just clicked when starting) on power and now stalls when started which it does immediately no long cranking.
The twist; truck has an aftermarket alarm by Python. Problem is I don't know anything about the alarm or if it comes with an immobilizer. I am in the process of trying to figure this out but need to pull dash or something to find the "brain"? Never had an alarm like this I disconnected the clear square that adjusts the sensitivity hoping that was it but I don't know where or what I assume the brain of the alarm is.
Ford Ranger / B-Series :: 2003 4.0L Idles Fine But Stalls When Given Gas
I'm having a bit of trouble with my fathers '03 Ranger Edge 4.0L. It has about 100k miles on it, and we keep it very well maintained. This is the first major problem we've had with it.
When the problem first occured, it had been driven about 30 miles on the highway and about 5 miles after getting off the highway, he pulled up to an intersection and stopped. As he started accelerating again, it all of a sudden started sputtering, surging (almost exactly as if it were running out of gas), and then stalled. It continues to exhibit this behavior. It will start and idle fine, but struggle and then stall when given any amount of throttle. It's also an automatic transmission if that makes any difference.
Fast forward to this past week after we had it towed home. We have checked the fuel pressure, and its dead on at about 64psi. We changed the fuel filter, changed the PCV valve, changed the upstream O2 sensor, put in a new air filter, cleaned the MAF sensor, and cleaned the intake of the throttle body. We're now at a loss as to what could be causing the problem. The CEL is not on, and there are no codes being shown when we plugged it in. We also thought it may have been bad gas, so we drained the tank and put fresh gas in from our preferred station. The plugs and wires are also fairly new, only about 4k miles on them.
Are we missing anything here? What else we could try? The absolute last resort is taking it to a shop, we're going through a rough patch with finances.
Ford Ranger / B-Series :: 1999 - Stalls In Hot Weather / Low Idle Otherwise
I have had my '99 Ranger since 2002. Since it has started getting hot in Texas, the truck has decided to stall at horrible times. When driving on the interstate, there is no problem, but as soon as I get in town and have to let off the gas to turn or stop, the whole truck dies. Unless it sits for a long time, it will continue to die at every stop. It is harder to start each time. I have changed the fuel filter and added STP to the last tank of gas. Also, it is tough to start and keep running until it has warmed up on any day. I have to sit in the truck and keep the idle up so it won't die.
View 1 RepliesFord Ranger / B-Series :: 1986 - Stalls When Hot / Won't Restart Until Cool
I have a 86 Ranger with the 2.3L fuel injected 4 cylinder and a 5 speed manual transmission. I can drive it for hours on the highway but if I get caught in stop and go traffic, it stalls and won't restart for about 10 minutes. When trying to restart it acts as if it is fuel starved. Spraying carb cleaner in the throttle body does make it run for a second or two. I was getting a code 18 & 67 before I changed the ignition module, now I just get code 67 or 11. I have done the following:
-Changed both fuel pumps, tank and frame rail pump (did one at a time, no improvement)
-Changed all fuel filters (in line filter, fuel reservoir filter and tank filter)
-Changed ignition module on distributer
-Changed both relays that control fuel pumps
-Cleaned battery terminals and body ground connections.
-New gas tank fill cap
I'm at a loss now as to what to do. I have been checking the codes with my multi-meter. I do not have a OBD1 diagnostic tool.
Ford Ranger / B-Series :: 1992 - Starts And Stalls / Won't Run More Than 3 Seconds
The truck started acting up while driving. It would shut off (no miss or anything), but would start again. Now it is sitting in the driveway and wont run more than 3 seconds. The fuel pump has been changed and did not work. The fuel pump relay is new and did not work. I read that the fuel pump goes to another circuit after start up. Could it be running to start and then shutting off? Inertia switch is not tripped. Where to look next. 1992 Ranger 6 cylinder ....
View 10 RepliesFord Ranger / B-Series :: Stumbling And Sometimes Stalls After High Rev Coming Down To Idle
My truck has been doing this since I got it and I can't figure it out. It's a 2000 Ford Ranger XLT 2.5 5Spd. It runs fine if you don't rev it above 2500-3000 rpm. After you rev it that high coming down to idle it is stumbling real bad and sometimes stalls. I've been driving it like this since I got it, and it does fine other than this. It gets better the longer you drive it, but it still will do it if you rev it high enough.
Here are all the parts I personally have changed (previous owner said he did the plugs and wires and air filter, which it looks like he did but I'm about ready to change them myself):
-Fuel filter
-coil packs
-timing belt
-egr valve
-cleaned throttle body
-iacv
-tps
-thermostat
Ford Ranger / B-Series :: Easy Start / Rough Low Idle And Stalls
My 2005 2.3l Ranger ran great. I moved a trailer about 150 feet and stalled the truck backing it up. Stick shift. Unhooked the trailer and pulled back into the parking area....all the sudden the truck has extremely rough idle and stalls. It runs good on the highway. AutoZone ran a OEM number to cross: P0171.
I cleaned the IAC with intake cleaner. No Luck
I unhooked battery for 15 min. No Luck
I sprayed intake with 1/2 can of intake cleaner. No Luck
I did not have a tamper torx to remove the MAF. What next.
Ford Ranger / B-Series :: 1989 V6 Stalls / Dies / Powerless After Warm Up
I've recently acquired a 1989 ford ranger xlt 2.9L V6 and iv got my elbows deep already..... starts right up and scene its an older truck i let it warm up for a few minutes seems to sound alright so i jump in and take off... well i make it about two blocks and as soon as the truck seems to warm up it starts to sputter and die out... starts back up and idles for a min and i try to take off, but it seems to have NO power and jerks and dies.... so i push to a street parking spot and get situalated start the truck up again and take off only to make it about half a block tell it does the same....
First i think iv run outta gas witch i might of not sure so I walk to station and get three gallons. put in truck and same is happening. so i start kicking myself for not haven any tools with me and i leave tell next day... that night do a little research and get some idea's of what could be the problem'(s) so i start out with things that look like they need tending Badly WIRES, PLUGS, ROTOR, CAP, MAP SENSOR, and now after a whole day in the rain (Northwest BTW) and grease to elbows? 2.9 V6? What step's should i take next?
Ford Ranger / B-Series :: 2000 - Stalls At Stop Lights / No Codes
I have a 2000 ford ranger 2.5 automatic. runs fine except when stopping at lights and intersections it stalls. I have changed the MAF, TPS and hasn't made a difference.Truck only has 64,000 miles. What to look at next. no codes...
View 14 RepliesFord Ranger / B-Series :: 1999 - Stalls / Rough Idle And Engine Dies
I have a 1999 B4000 4.0L with 160K miles on it. Bought the truck new. Up until about a year ago it ran perfect but has developed an idle, stalling and occassional jerky ride problem. It occurs at any temperature, engine hot or cold, A/C clutch on or off and in Park, Drive or Neutral. When you start the engine it will not idle unless you keep your foot on the gas. The idle speed will drop to 200-300 rpm and the engine dies. Sometimes you can barely tap the gas pedal and the rpm will shoot up to normal idle speed (about 900 rpm) and stay there a few seconds then begin to drop again. If the engine is cold it will often die a couple times after starting even with the foot on the gas and then about the 2nd or 3rd time run with your foot on the gas.
At stop signs and red lights you have to keep your foot on the gas to keep it running. If you are approaching a stop sign and take your foot off the gas to coast to a stop and brake, the engine rpm will drop and the engine will die. It always starts fine though. Once you are driving it generally runs just fine at low or high speed. You can generally set the cruise control on the expressway and cruise right on. However, sometimes all of a sudden the truck will start bucking and jumping as if it has a terrible misfire. It usually lasts a few seconds and quits. Often if you step on the gas it quits. Even less occasionally the engine will begin to slow as if it is starved for fuel and slow down. You can press the pedal to the floor and it sputters a bit then picks up and runs fine.
I have read about all the threads in this forum and others and tried some of the suggested fixes but it still has the problem. I have tuned it up with new plugs, wires, fuel filter, air filter and PCV valve. Based on some of the forums advice I have replaced the IAC valve, the EGR valve and EGR Pressure Feedback Sensor, and cleaned and inspected the MAF sensor with MAF cleaner. I have checked all my vacuum lines and no leaks there and checked the engine timing which is fine. Fuel rail pressure and engine compression are also fine. Spark plugs show no clues, exhaust is clean and the engine uses virtually no oil. There has been no tear down on the engine like removing the heads, cam, timing gears or any of that and the engine is completely stock.
It shows no codes related to the problem. Two or three months after the problem started I showed a code that indicated an injector problem, traced the problem to a bad injector, replaced the faulty injector and it was fine. That took care of that code but didn't solve the idle problem. In my younger days I was into drag racing and I rebuilt engines, swapped transmissions, etc. and still do my own tune-ups today so I am fairly familiar with auto repair and have most of the tools for testing newer cars but this one stumps me. As a last resort I'm about to take it to the dealer.