Ford Ranger / B-Series :: Truck Stalls While Driving
1994 FORD RANGER stalls while driving - differant speeds ...differant miles ...no rhyme or reason to it - cranks right back up ...can even pop clutch and cut it back on. Already replaced Ignition Start Module - Dpes sensor - temp sensor - and scan shows all codes are clear and truck passes. We are clueless to whats causing this. 4 cyl 2.1
View 12 RepliesFord Ranger / B-Series :: 1989 V6 Stalls / Dies / Powerless After Warm Up
I've recently acquired a 1989 ford ranger xlt 2.9L V6 and iv got my elbows deep already..... starts right up and scene its an older truck i let it warm up for a few minutes seems to sound alright so i jump in and take off... well i make it about two blocks and as soon as the truck seems to warm up it starts to sputter and die out... starts back up and idles for a min and i try to take off, but it seems to have NO power and jerks and dies.... so i push to a street parking spot and get situalated start the truck up again and take off only to make it about half a block tell it does the same....
First i think iv run outta gas witch i might of not sure so I walk to station and get three gallons. put in truck and same is happening. so i start kicking myself for not haven any tools with me and i leave tell next day... that night do a little research and get some idea's of what could be the problem'(s) so i start out with things that look like they need tending Badly WIRES, PLUGS, ROTOR, CAP, MAP SENSOR, and now after a whole day in the rain (Northwest BTW) and grease to elbows? 2.9 V6? What step's should i take next?
Ford Ranger / B-Series :: 1999 - Stalls / Rough Idle And Engine Dies
I have a 1999 B4000 4.0L with 160K miles on it. Bought the truck new. Up until about a year ago it ran perfect but has developed an idle, stalling and occassional jerky ride problem. It occurs at any temperature, engine hot or cold, A/C clutch on or off and in Park, Drive or Neutral. When you start the engine it will not idle unless you keep your foot on the gas. The idle speed will drop to 200-300 rpm and the engine dies. Sometimes you can barely tap the gas pedal and the rpm will shoot up to normal idle speed (about 900 rpm) and stay there a few seconds then begin to drop again. If the engine is cold it will often die a couple times after starting even with the foot on the gas and then about the 2nd or 3rd time run with your foot on the gas.
At stop signs and red lights you have to keep your foot on the gas to keep it running. If you are approaching a stop sign and take your foot off the gas to coast to a stop and brake, the engine rpm will drop and the engine will die. It always starts fine though. Once you are driving it generally runs just fine at low or high speed. You can generally set the cruise control on the expressway and cruise right on. However, sometimes all of a sudden the truck will start bucking and jumping as if it has a terrible misfire. It usually lasts a few seconds and quits. Often if you step on the gas it quits. Even less occasionally the engine will begin to slow as if it is starved for fuel and slow down. You can press the pedal to the floor and it sputters a bit then picks up and runs fine.
I have read about all the threads in this forum and others and tried some of the suggested fixes but it still has the problem. I have tuned it up with new plugs, wires, fuel filter, air filter and PCV valve. Based on some of the forums advice I have replaced the IAC valve, the EGR valve and EGR Pressure Feedback Sensor, and cleaned and inspected the MAF sensor with MAF cleaner. I have checked all my vacuum lines and no leaks there and checked the engine timing which is fine. Fuel rail pressure and engine compression are also fine. Spark plugs show no clues, exhaust is clean and the engine uses virtually no oil. There has been no tear down on the engine like removing the heads, cam, timing gears or any of that and the engine is completely stock.
It shows no codes related to the problem. Two or three months after the problem started I showed a code that indicated an injector problem, traced the problem to a bad injector, replaced the faulty injector and it was fine. That took care of that code but didn't solve the idle problem. In my younger days I was into drag racing and I rebuilt engines, swapped transmissions, etc. and still do my own tune-ups today so I am fairly familiar with auto repair and have most of the tools for testing newer cars but this one stumps me. As a last resort I'm about to take it to the dealer.
Ford F-150 - 1997-2003 :: 2001 - Truck Stalls / Dies While Driving Down The Road
Got this truck used, it is a 2001 F150 4 door lariat 5.4, 4x4. It now has around 108k miles on it. The truck dies while driving down the road every couple weeks or so. It will restart after a minute or so and then seems to be fine. The ABS light is on, no codes or CE light.
The last couple months while your going down the road it revs up to 4k rpms or so while your driving like the OD is turning off. The other day it wouldn't start in the morning, I changed the fuel pump relay and it fired right up. I put the old relay back in and it still fired up!!!!
I decided to take it to the dealer today and on the way to town it shifted out of gear while driving at speed, the speedo turned off and the odometer turned off as well. I shifted to N and then back to D, nothing, I hit the OD button and it flashed but still no go so I coasted to a stop, truck was running at idle.
I turned it off, restarted and everything worked just fine again and went on my way to the dealer. Still no CE lights.
Ford Ranger / B-Series :: 1990 - Rough Idling / Truck Dies
1990 Ranger 2.3L 4 cylinder. The truck idles so rough it dies. It runs fine going down the road it just seems to "load up" at idle. I know there are hundreds of things that it could be, I just hate to start throwing parts at it. It is definitely running rich at idle.
It is one of those trucks that we have replaced a lot of parts. The scan tool said something about setting the timing??? Is there a way to set the timing? There is no distributor, and it is the one with 2 coils and 8 plugs.
Ford Ranger / B-Series :: Truck Almost Dies And Starts Sputtering - Spark Plug Caps Pop Off
My 2003 2.3L used to run bad... it had a lot of lag to it when i would try to accelerate. The check engine light was on so i got it checked, and the reading said o2 sensor high voltage or something like that... anyways, i purchased a new sensor (i researched, and found there is only an upstream o2 sensor), replaced it, and the truck ran WAY better, no more lag during acceleration, it was crisp. As i was driving home one day, i was accelerating up a hill, and at about 4000 RPM, the truck almost dies and starts sputtering.
The check engine light started flashing, so i new it was serious, but luckily i was able to make it back to my house. When i got home, i looked under the hood and noticed that #2 & #3 spark plug caps had popped off the spark plugs. What I don't understand is what would have caused that to happen in the first place.... Is it a clogged Catalytic convertor, or is the o2 sensor bad.... Ive read different opinions and technical diagnostic possibilities, but man, i don't want to throw a bunch of money at a truck that I'm really going to have for a few more months. but I need to get it fixed in the mean time.
Ford Ranger / B-Series :: 1992 - Truck Will Fire While Starter Engaged But Stalls When Key In Run Position
My truck will fire while the starter is engaged ,but stalls when the key is in the run position. This is my plow truck and I don't want to go through the winter without it.
View 14 RepliesFord Ranger / B-Series :: 1985 - Bogs And Dies While Driving
I have a 1985 ranger 2.3l efi and it bogs and dies while while driving, it can sit and idle all day long but when you go to drive it, it works great for 3-4 minutes then out of nowhere starts bogging sometimes I can keep it going a little longer but in the end the truck always dies . I know I'm loosing fuel pressure , I hooked a gauge up to it and drive it down the road when the truck died it showed 10 psi , from here I'm lost . It has a new fuel pump in the tank and I can hear the other one running when I click the key on , Also two new fuel filters .
View 3 RepliesFord Ranger / B-Series :: 1987 - Engine Dies While Driving
Recently, today in my 87 Ranger suddenly the engine dies and all electronics in the cab fail.
I noticed under the hood that the fusible link connected to the battery and an orange and black wire was smoking. Tracing this line i found that it leads to the ignition switch, as well as some other places.
There is another fusible link and the junction between the yellow ignition wire and the orange and black wire from the battery. This fusible link also was failed.
I'm planning on replacing the fusible links tomorrow but in case that does not fix it, where to look next.
The problem only occurs when the key is in the ON position. I'm thinking maybe I could do some tests with a multimeter on the ignition switch but am not sure of the details of what I should test for.
Summary: Fusible Links C, and E burn out when the ignition is in the ON position.
Ford Ranger / B-Series :: 1992 - Engine Dies Randomly While Driving
I have just inherited my recently deceased father's 1992 Ranger with the 2.3 liter engine. He was a Ford Mechanic but got to ill to worry about fixing the Ranger. So, let me begin, the engine dies randomly, (at idle or in gear driving doesn't matter what gear or speed), turning key to off and then to on will allow vehicle to restart every time. No "Check Engine" light has ever lit, I do have an "Antilock" light that comes and goes. The engine codes I keep getting are: 10, 218 and 222.
Code 10 is a computer check code,
Code 218 is "Loss of Ignition Diagnostic Monitor (IDM) signal/left side, and
Code 222 is "Distributorless Ignition System - Loss of right side ignition diagnostic monitor (IDM) signal.
These codes were from my Innova reader. I have read where other similar problems were fixed with a new Crankshaft Position Sensor, replaced mine, no change. Another symptom I just noticed is my temp gauge stays near the cool end when it should be higher.
Ford Ranger / B-Series :: 2004 XLT Stalls While Decelerating - Code P0733
I have a 2004 Ford Ranger XLT 4.0L that is fully stock. Back in December the truck stalled while braking to a stop at a red light. No check engine light, no O/D light flashing, just died. I restarted it and it ran as if nothing happened. It ran fine for a few weeks and just when I am thinking it was an isolated incident it happened again, restarted, ran fine. It seems to be shifting normally through all gears, every once in a while it feels like it might shift from 2nd to 3rd a little pre-mature but that may just be my imagination. A month ago I felt a VERY slight jerk, almost unnoticeable, while pulling into a parking spot and the O/D light started flashing. A couple days ago (which was a little over a month since it last happened) it done it at 3 consecutive red lights. Been running fine since. Had the code read and it was P0733 Gear 3 Incorrect Ratio. I changed trans fluid in February and fluid level is fine.
View 3 RepliesFord Ranger / B-Series :: 1992 - Truck Stopped Running While Driving / Started Again Then Died
I have a 92 ranger 6cyl 4L. The truck stopped running while driving then kicked on again, it did this several times over about 20 minutes then finally died and now I can't get it started. I recently replaced the fuel pump and filter and spark plugs and wires. I get spark if I ground the plug and some gas will pour out of the fuel pressure test valve when I stick a screws driver in. When I check engine codes I get an all pass. Truck will turn over and sometimes run for 2 or 3 seconds but that is it.
View 2 RepliesFord Ranger / B-Series :: Truck Idles With Very High RPMs When Driving And Shifting Gears
1999 ranger, 2.55 speed. truck idles with very high rpm's when driving and shifting gears. have changed the AIC, mass air sensor. Throttle position sensor and still does it. the AIC has been changed 5-6 times in 6-8 months as parts store kept telling me it was that. What can i look at, check, etc...
View 6 RepliesFord Ranger / B-Series :: 2004 Truck Won't Start After Slow Down Or Quick Stop
This has happened 3 times.
1st) pulled quickly over to side of road, shut off truck. It would not start then. Towed it to service station and it started the next morning (with no repair made). I wonder if tow ride dislodged the the blockage in fuel line(?). Always sounds like it's going to turn over, but like not getting fuel.
2nd) Went to leave work, truck wouldn't start. Towed to my mechanic and he replaced fuel pump. Thought it was fixed because it ran fine until just the other day.
3rd) Slowed down to complete stop in heavy traffic and it stalled. Would not restart. Again sounded like it was going to start but didn't seem to be getting fuel. Good samaratins pushed me off road. Had it towed to mechanic. Started the next morning without any repair or service. It's like the tow ride and bumps getting it off the tow truck dislodges what ever is blocking the fuel line.
My mechanic replaced the fuel pump, but I don't think her replaced the fuel filter.
Ford - Ranger :: 2004 - Truck Does Not Pull To One Side Or The Other While Driving
i have a 2WD 2004 Ford Ranger regular cab. I have replaced the rotors three times in the last year due to warpage. What is causing this? The truck does not pull to one side or the other while driving. applying the brakes don't cause it to pull to one side either. According to my mechanics, neither caliper is sticking. the right brake pad does show some signs of heat damage (cracking). There is no uneven tire wear. I have a buddy who thinks it may be a bent wheel hub, but my mechanic says no because no uneven tire wear. They are leaning to a faulty brake hose, but can't say for sure.
View 3 RepliesFord Ranger / B-Series :: 2004 - 4 Wheel Drive Kick In And Out When Driving
My 2004 Ford Ranger has 220,000 miles, runs great, and when I bought it this summer the 4 wheel drive worked great. Starting when the weather got cold when I engage the 4 wheel drive (no lockouts electronic engagement). I will drive and it will kick in and out of 4 wheel drive when it starts to slip or I have to accelerate.
When the 4 wheel drive kicks out I will let off the gas then it will engage again on its own, but will slip out again when on ice or I start to slip. When the 4 wheel drive engages it does NOT make any strange sounds, no clunking or nothing, it engages smoothly, and disengages properly.
What it could be? a connection? Any way to fix or diagnose the problem? I have been told that it probably is not the transfer case, because if it were it would not engage or stay in 4 wheel drive at all.
Ford - Gasoline - Thunderbird :: Stalls And Dies After A Few Minutes Of Driving
I have a "56 thunderbird with a mid-60"s ford 390 engine w/ 4 bbl holley. I just had engine completely rebuilt and everything else is new: carb, distributor, electric fuel pump, fuel tank, etc.
Problem: car stalls and dies after a few minutes of driving. Generally restarts after waiting about a half hour, but not always. I have a fuel filter with clear bowl in fuel line just ahead of carb. The bowl is usually about 2/3 full of fuel, but general appears empty when the car stalls.
After waiting a while, the bowl refills and the car restarts.
Ford Ranger / B-Series :: 2001 - CEL On / Low RPM And Stalls
My Ranger has been acting funny lately. My check engine light is on. I stopped by an Autozone and the guy read the codes - I don't remember exactly what the code was but he said I just needed to use some fuel cleaner - he recommended Seafoam. Now, I assume he was just trying to sell me something. But I've tried that, Gumout and STP in the tank with no luck.
If I'm driving and come to a stop, my RPM dips down to about 600 or lower, my truck starts shaking and will eventually stall if I don't step on the gas. This only happens with a warm engine - If I start the car up and go a mile down the road, it won't happens. But if I go 10 miles down the road, it will. I assumed I had a bad throttle position sensor so I just ordered the part and replaced it but the same behavior exists.
It's been a while since I've replaced the fuel filter - it might just be that.
Ford Ranger / B-Series :: 1984 - Dies While Turning Right?
I didn't really know where else to turn (no pun intended) every time I turn my wheel to the right the truck sputters out and dies, i checked the ignition switch, tightened her up and shes still killing the engine when i turn right. All other power remains on stereo, car charger etc. its not so bad on continuous turns i can just pop the clutch but for stopping and turning its a huge issue. Why turning left is fine but right kills the engine..wondering if maybe the prongs on the ignition switch may be bad?
View 7 Replies