Ford Ranger / B-Series :: 1996 - Transmission Grinds When Putting It In Reverse
I own a 1996 XL Ford Ranger 2wd 5 speed manual.
Last week I had it in for some service, which included bleeding the clutch lines and new fluid.
Since then when putting it in reverse the transmission grids. It is also very difficult to get into first gear - I really have to shove hard on the stick.
Better Description of symptoms: When the vehicle is moving it shifts fine. When I come to a stop, put it in neutral and let out on the clutch, it is then very difficult to get back into first gear. If I leave the clutch in, fter I come to a stop, I can shift around to all the gears no problem. It's only when I let out on the clutch, then push it back in to shift into first is the difficult part.
With reverse, I have to move ahead a bit, THEN I can shift to reverse without the grinding noise. I talked to my mechanic who check to ensure the fluid was NOT low (it wasn't) and no air bubble existed in the line. After that was checked, he said the clutch is worn and has to be replaced.
Well, then, why wasn't it doing this BEFORE I had him bleed the lines? It started the day I picked the truck up from service. He recommends the following to fix the problem...
- slave cylinder
- new line
- disc
- preasure
I am asking why this would happen after he bleed the lines? Is there another problem that can cause this?
Ford F-150 - 1997-2003 :: New Starter Won't Disengage?
The starter on my kid's truck doesn't disengage and continues to turn over after the ignition is off. I have seen a few posts on this but have yet to find a clear troubleshooting path and it seems a lot of money wasted on new starters, solenoids and new ignitions.
View 4 RepliesFord Ranger / B-Series :: 1998 - Won't Disengage Out Of 3 Gear?
I have a 1998 ford ranger and it will not disengage out of 3 gear. The truck still starts but if you let of the cutch. Of course, It stalls. I'm doing the work myself but where I should start looking.
View 1 RepliesFord Ranger / B-Series :: Clutch Would Not Disengage At Any Time
This morning, I shifted into neutral and left the truck running. When I got in it put it in reverse, the shifter peddle went all the way to the floor and the clutch did not engage. I turned off the engine, and the transmission shifted easily. I put it into reverse, started the engine, and when I tried to shift back into first, the same thing happened. Pedal to the floor with no resistance, and I could not get it into gear. I finally forced it into 1st to get back into the driveway, but had to stall the engine to keep from going through the garage door. The clutch would not disengage at any time. I checked the master cylinder and it is 1/2 full. Has my clutch gone out?
View 14 RepliesFord F-150 - 1997-2003 :: 1999 - New Starter Won't Disengage
Starter problem with my 1999 Ford 5.4 f150. Last few days I’ve had to cross the solenoid terminals in order to start up. After replacing the solenoid the starter would not disengage. Put the old solenoid back on, crossed term and the starter did the same thing. Bought new starter (what a job finding the upper bolt) replaced old one, and I’m still hearing the starter running along with the motor. What else?
View 11 RepliesFord Ranger / B-Series :: 1989 - Disengage Electronic Shift?
I recently acquired a 1989 Ford Ranger midsize pickup with an electronic shift button/console between the visors. I put it in 4WD and the manual does not indicate the procedure to take it out of 4WD. What is the procedure?
View 3 RepliesFord Ranger / B-Series :: 2003 V6 Hard Time Starting
I own a 2003 3.o v-6 ranger, after a short or long drive, my truck has a hard time starting.. Starts fine before any driving..
View 12 RepliesFord Ranger / B-Series :: 1993 - Cruise Will Not Disengage With Brake Pedal
1993 Ranger XLT 4.0 AT. Initially replaced ECM for other problems and then noticed Cruise w/n disengage when brake depressed unless pedal is pushed several times and with more pressure. Put in another ECM and have same problem. Have replaced the brake switch and lights come on as they should. When pedal is pushed the vacuum dump valve on the pedal will dump the vacuum to the servo but when you release the brake pedal the cruise control kicks back in and speeds truck back to set speed.
So this tells me that the dump valve is only a fail-safe feature for when pedal is depressed and does not actually deactivate the servo. Everything else with the cruise works fine: On/Off switch, Set/Accelerate, Resume, Coast. How to proceed next? Like where to find speed control module and how to test it? How to check servo to see if it is getting or dropping voltage that will electrically disengage it, etc? Don't want just throw parts at it. The new ECU's that I used came from ECU Exchange in Florida and there still remains the possibility that they are still the problem.
Ford Ranger / B-Series :: Shifting Hard / Clutch Won't Disengage At All After Master Cylinder Replaced
My Ranger had been shifting hard for quite awhile. I recently opted to go ahead and replace the clutch, throwout bearing, had the flywheel turned and replaced the pressure plate.
This just seemed to make the problem slightly worse. I thought it was possible that my master cylinder needed to be replaced (the slave was replaced two years ago and didn't appear to be leaking when I had the tranny off). I replaced the master cylinder and now the clutch won't disengage at all. I've spent several days trying different things to bleed the clutch, and I just can't get it to bleed. I took it back off and bench bled it, then put it back on and bled through the whole system. This isn't working. I've tried numerous suggestions-jacking up the back end of the truck, jacking up the drivers side of the truck, I even bought a vaccuum bleeder and used it for 2 hours just having an assistant fill up the reservoir while I sucked fluid out the bleeder valve. The best I could ever get was some resistance on the pedal, but not enough to push the disc away from the flywheel.
I took the pickup to Ford, they said they bled it and charged me 90 bucks and still couldn't get the clutch to release
Ford Ranger / B-Series :: Vacuum Lines Bad On Driver Side / Actuators Won't Disengage Properly
I noticed that one of my vacuum lines was bad on the driver's side. I've done a lot of reading on the 4WD systems and frankly I'm confused now. My understanding is that when in 2WD the solenoid is open pulling a vacuum on the actuators (IWE) which keeps them disengaged. When you switch to 4WD the shift motor on the transfer case sends power to the front wheels and the solenoid turns off the vacuum which engages the actuators sending power to the wheels. Therefore if there is a vacuum leak the actuators won't disengage properly.
Through my trouble shooting I've determined that I think the solenoid is working properly because I'm getting a vacuum when in 2WD and no vacuum in 4WD. I believe that both actuators are engaged and working properly when in 4WD. However, I must not be getting a vacuum to the driver's side actuator (hub) because the line is totally busted up and can't possibly hold a vacuum. However the passenger side line looks good to me. Does this mean that I've been driving around in "3WD"??? I don't seem to have any problems when in 2WD turning (no tire skip or hop).
Ford Ranger / B-Series :: Clutch Start To Engage / Disengage At Half Way Point On The Pedal Travel?
So I just had my entire clutch replaced while another repair was taking place. What I've noticed is the "clutch engagement" has changed. Where as I would have the clutch start to engage/disengage at the 1/2 way point on the pedal travel is now the last 1/4 of the pedal. Is this a "normal reaction to a new clutch that just takes getting used to or is there an adjustment I can fine turn it with? Do I just have to wait for it to "break in"? When I replaced the clutch on my dearly departed 94 ranger, I replaced the bearings & disc only reusing the pressure plate and did not have this issue.
View 3 RepliesFord Ranger / B-Series :: New Starter / Turns Over But Won't Fire
So my sister has a 2000 Ranger 2.5L. I put in a new starter today for her today, and the second I re attach the battery terminal it turns over but wont fire.?
View 4 RepliesFord Ranger / B-Series :: 2002 Truck Won't Start At All Even After New Starter
I have a 2002 Ford Ranger, and it wont start at all. Ive replaced the starter, had the battery checked. Not the battery, took starter out, had it checked too, its not the starter either. Someone said it maybe a fuse? This is totally frustrating, and I need to get it figured and fixed asap. Its been going on for weeks., I had it fixed and then it just stopped. It wont even take a jump anymore.
View 4 RepliesFord Ranger / B-Series :: 1995 - Truck Would Not Start / Starter Locked Up
I have a 95 Ford Ranger 2.3L with a five speed. I recently had a starting issue were I parked the truck, went into a store came back out and the truck wouldn't start. Figured it was the solenoid as I couldn't jump across it to get the truck to start. Replaced the solenoid. Still no go. Found a fuse in the starting circuit blown. Replaced the fuse and got it started and drove home. Next morning, I go to leave for work and the truck would not start. Got a ride to work came home and checked it over and found the starter locked up. I replaced the starter. Truck started for a few days and now I am having problems again.
Here is the problem I am having now. Starter is good. Proved that as I can start the truck by jumping across the starter relay. Checked the solenoid with a voltmeter and it is doing what it is supposed to do when the truck starts normal. Here is where I am scratching my head. I can start the truck sometimes and it starts just fine. Next time I try to start it, the fuse will blow.
Replace the fuse and it might work for a couple of starts and then the fuse will blow again. I jumped pass the fuse with a piece of wire for diagnostic purposes. Out of 20 starts, it only started normally 4 or 5 times. I have checked every wire I can see under the dash and have not found any obvious issues. I am at a point where I am so frustrated that I just want to push this 400k mile truck into the back forty and put it out of its misery like a lame horse.
Ford Ranger / B-Series :: No Movement From Starter Motor When Key Is Turned To Start
I have a 2002 Ford Ranger with a 3.0L engine that is having some issues with starting, here is what is happening.
Every so so often when the key is turned to start there is no movement from the starter motor. The battery is fine and all of the dash lights stay on while the engine is not starting. I have replaced the starter with a remanufactured model (possibly a mistake), and also replaced the clutch interlock switch.
I have attempted to change the ignition switch but the replacement I received did not even try to turn the starter (after many tries), like possibly it was faulty out of the box. I am currently using the OEM ignition switch as it will at least turn the starter eventually. I just worry that this problem will develop further at the wrong time.
Ford Ranger / B-Series :: 1987 - No Power / Starter Died And Solenoid Was Just Clicking
Well it all started when I was having starter issues my starter died and my solenoid was just clicking and after time there was no power at all to anything in the truck i have replaced the solenoid and starter and check battery and cleaned post and terminals. I am going to replace my negative cable as it was pretty bad but if this still does not work, so what to look for. The truck is an 87 ford ranger 4x4 5 speed with a 2.9....
View 9 RepliesFord Ranger / B-Series :: 1986 2WD Not Running - Shift Linkage In Way To Change Starter?
But here's too my question. I recently bought a 2wd Ford ranger 2.9 automatic. Bought not running. They said it wouldn't turn over that there was something wrong with the starter. I figured it was the neutral safety switch turned out it was there's a wire broke on it. I can get in there touch the wires together and it'll turn over. But I can't fix it because the shifting linkage is In the way. I'm wondering how too take it off. I've never worked on one before. And I don't wanna mess up my gears.
View 1 RepliesFord Ranger / B-Series :: Truck Started On Its Own / Wouldn't Shut Off And Starter Engaged In Park
So I turned off my truck the other day, got out, and it started again on its own. Confused, I looked in my hand to see my key. I got back in, and tapped the brake thinking the command start had engaged, even though I did not have the remote with me. It continued to run. So I put the key back in the ignition, turned it to ON and back OFF. It still ran. I had to run inside for a half a minute so I left it running.
Came back and drove away with no issues. When I stopped again about 2 minutes later and shifted to PARK, the starter engaged making it's terrible 'hey stupid, I'm already running' sound. I tried shutting it OFF quickly but it still ran and made it's skinning crawling noise. So I quickly shifted back to DRIVE. All the gears worked fine but PARK and NEUTRAL had the starter engaging. I also could not shut the truck off from DRIVE as the key would not turn.
I drove over to a local garage and called them from the truck as I was effectively trapped in the truck with my foot on the brake, unable to shift to PARK or turn it OFF. No supporting staff. So I drove back to work where I had a co-worker remove the battery cable at which point I was able to shift to PARK and turn OFF the truck. I let it sit like that for about 10 minutes and haven't had a problem since.
What happened?? And for the record I can put gas in the tank and changed my own oil, but that is the extent of my vehicle knowledge.
Ford Ranger / B-Series :: 1992 - Truck Will Fire While Starter Engaged But Stalls When Key In Run Position
My truck will fire while the starter is engaged ,but stalls when the key is in the run position. This is my plow truck and I don't want to go through the winter without it.
View 14 Replies