Ford Ranger / B-Series :: 2003 - High Idle And Shoot Up Between Shifts / No Codes
My '03 Ranger is having a high idle problem. It's a 3.0, manual, 2wd, 141,000 miles. When it's cold it will idle at about 1500 but once I drive it, even just to the end of the block, it will idle at about 3000 and shoot up towards that between shifts. At a traffic light it will idle at 3000 and maybe go down to about 2500. If I bog it down with the clutch it goes right back up once I put the clutch back in or put it in neutral.
I replaced the IAC, no luck. I cleaned the MAF and checked the voltage on the TPS and it is good. I replaced the PVC valve, but the old one was fine anyway. I've sprayed around with carb cleaner and don't notice any difference. I've plugged it into my dad's AutoTap which lets me monitor everything on my laptop and the only thing I can see that looks suspicious is that even with the engine off, the Absolute Throttle Angle reads 18.8%. If I step on the gas with the engine off it goes up to 91.8% so I would imagine that just has to do with the function of the TPS and probably isn't out of the ordinary, but I don't really know what that number means or what the Absolute Throttle Angle is or is supposed to be.
Short of taking the intake plenum off and physically inspecting it for cracks, I'm stumped.
Ford Ranger / B-Series :: 2003 - Clank Sound When The Truck Shifts From 1st To 2nd
I have an 03' Ranger and I assume it has the BW 1354 tcase. I am getting a "clank" sound when the truck shifts from 1st to 2nd. I am thinking its the rear output yoke on the t case. I can grab it and move it up and down but there is no fluid leaking or anything. Would this be a rear bearing problem?
View 2 RepliesFord Ranger / B-Series :: 1987 XLT - High Idle When Started For About 6 Minutes
My ranger 2.9 automatic 2WD has an high idle when started for about 6 min, engine can be hot or cold, still get the high idle, then it will drop to around 900-1000. I've changed the Idle control twice, checked EGR function. Replace temp sensor. Disconnected battery for 15 min. No code output.
View 7 RepliesFord Ranger / B-Series :: 1984 2.8L Started Then Revved Up High And Shut Off Immediately
I just rebuilt the carb on the truck, it has the 2.8L, and when I went go go start it, it cranked for awhile until fuel filled the bowl, then it started and revved up high, I shut it off immediately and it turns out the throttle linkage was binding for some reason, I fixed that but now it wont restart.
I was cranking it for a while and gas started spewing out of the top, so I took the top of the carb off and reset the float height and now it doesn't spew gas.
I pulled the plugs and checked for spark and it's a really bright blue spark. I'm thinking it's just flooded, lots of gas on the plugs? I'm just waiting for it to clear out now and trying to brain storm what could be wrong.
Ford Ranger / B-Series :: Started Revving Real High (about 4000 RPMs) And Getting No Power (20 MPH)
Two days ago, I was driving on a North GA steep, windy, mountain road in my 2002 v6 4.0 Ranger. All of a sudden, i started revving real high (about 4000rpms) and getting no power (20mph). I pulled over immediately and transmission fluid was pouring, by the quart, out of my truck. I didnt get to look exactly where it was coming from, since i backed away once i saw a small flame coming from the leak. i then called a tow truck (assuming it was a seal or a hose break) and had it towed to my house.
I started investigating the possible problems and didn't really see anything noticeable under the truck (not that I was expecting to). So what I did was put three quarts of transmission fluid in the dipstick hole and put in gear to see if I could spot a leak. nothing. then I drove it around the block to get it warmed up and put a little pressure on the transmission by driving up a semi-steep hill to see if that would spark the leak again. still no sign of the a leak.
And finally, when I went to go check the dipstick after my test drive, it read to be above the cross hatched area, hence being overfull. What my next step should be?
Ford Ranger / B-Series :: Runs Rough For About A Minute After Engine Started When Cold
This has been an ongoing issue for about a month. When I start the engine after it has been sitting and is cold it runs ruff for about a minute then smooths out and runs fine. I pulled a P0304 code (cyl.4 missfire) but I do not get a CEL.
I checked the plugs and they were ok but I changed them and the wires anyway as it just turned 50k and the plugs were original. I could live with a little cold ruff idle but the code throwing bothers me. The truck is a 2000 xlt 4x with auto trans. and 4.0 engine. This is my second 4.0 ranger but I have only had it for about 6 months.
Ford Ranger / B-Series :: Check Engine Light Started Blinking On And Off - Code 327 / 328 And 334
I've got a 1992 Ford Ranger 2.3L with about 240,000 miles on it. The check engine light started blinking on and off pretty regularly so I pulled the OBD1 continuous memory codes and came up with this.
327 - EVP/EPT circuit below minimum voltage
328 - EGR closed valve voltage lower than expected
334 - EGR closed valve voltage high
I can't say these codes mean a whole lot to me besides I've got issues with my EGR valve and possibly the EGR valve position sensor. I was thinking I'd start by replacing the EGR valve.
Ford Ranger / B-Series :: 2003 - Antifreeze Drip Coming From Up High Around
I have had a small antifreeze drip coming from up high around what I have been thinking was the water pump gasket. I have not pin pointed it exactly though. for the last 3 days i have been getting code po174 and now added po171 to that list. Also have something going on with my fuel fill vent or something as for a while now i have had to slowly squeeze in fuel to keep the pump from auto shut off on me like its full already. I have tried cleaning out that vent tube by spraying in carb cleaner even blowing on it but it seems to be a check valve, not able to blow in. i am thinking tonight that antifreeze leak may be related to those codes too. any thoughts? its on my 2003 ranger 3.0 flex fuel.
View 9 RepliesFord Ranger / B-Series :: 2003 3.0 V6 - High Idle In The Mornings When Cold About 2000 RPM
Truck is a 2003 Ranger EDGE 2wd auto w/140K miles (looks new) that was a one owner truck I recently bought. Came from Texas and is clean and was well maintained I got all service records up until I bought it in the fall last year. OK now the problems...
First...it has a high idle in the mornings when cold about 2000RPM. After it warms up it settles to about 800-900RPM but is VERY ROUGH to the point where it feels it will stall. I DID replace the spark plugs and the plug wires look newer and are not OEM. I DID remove and clean the IAC and it does not look very dirty but I did slightly clean it anyway.
When I did this I disconnected the battery for 20min. After I put it back together it ran smooth for about the first 10 minutes then same rough idle came back. I was told this truck has no EGR so that's not an issue. There are NO CODES and when I ran my pocket scanner nothing comes up either. Should I just go to NAPA and get a new IAC anyway? What else can I do?
Ford Ranger / B-Series :: 2007 - Shifts Into Gear But No Drive
My gf's dad said I could have his 07 Ranger 4.0 2wd with 230K on the clock if I fix the tranny 5R55E. One day he was driving home and all of a sudden had no drive. The tranny will run thru drive, neutral and reverse, but has no drive to it. Engine revs with nothing to show.
Tranny fluid was very dark and pan had nothing but the usual "metal flour" in it. I stopped there, did not pull the filter or anything else.
Ford Ranger / B-Series :: 2003 - Valve Cover Leak / Exhaust Smell Then Started Bogging / Dying And Shaking
I have a 2003 ford ranger 2.3 vin d 5 speed, this truck originally... Took it in for wires plugs front brakes fuel filter battery and added a small cold air intake. We discovered a valve cover leak and while repairing guy drops a screw into a valve and when finished he started it lodged the screw between the valve, shearing off a cam sprocket bolt. Throwing the timing. 2 valves on the exhaust side were bent and replaced. no damage to the head.
Timing was reset and the truck was running. 2 days later truck is running/had a hint of exhaust smell then started bogging dying and shaking, at which time we got an 02 bank2 lean code and fixed that. it cleared code and didn't fix it. From there we replaced coil, imrc intake bc of a crack, tried and check all vacuum, reset the timing. Timing would slip before but no longer than 10 minutes every time truck started.
Found the hole in the timing cover that holds the bolt to torque? to harmonic balancer was broke. replaced along with the diamond washers and cam sprocket bolts. timing finally held crank sensor was adjusted. truck came home for one day running good, we had removed the cold air intake and replaced the factory air intake. next day it was so slow outta first gear, you must baby the throttle, if you floor It, it sputters and kinda pops, truck stays slow all the way to about 10 mph and 2000rpm then it begins grabbing speed, 3000rpm is where this truck shifts the best, 2nd is better, third better than that.
As rpm increase the truck runs better, it idles steady at 1100-1200rpm at stops with an audible miss and then struggles again on takeoff. Here what im wondering, the truck has an abs sensor that just came on, but no codes showing now.tomorrow I wil run matko determinator 3.0 on it. and test the catalytic converter. first how do I check the timing belt to see if it stretched? do these trucks store the p.i.d.s. koer or kams that could cause one, all, or any of this and if so do I have to have it flashed from ford or can you manually do this without a drive cycle test.
Ford Ranger / B-Series :: 1989 Automatic Transmission Shifts Hard Into Second
I got this 89 ranger xlt with a 2.9 and automatic transmission. I mainly bought it because it was in such good shape and I was planning on putting a 5.0 in it. everything works on it. the a/c, radio, lights and it runs real nice. the only problem it has is it shifts pretty hard going into second gear. every once in a while it will shift smoothly into second but only like once or twice a day. he said he had recently changed the trans filter and fluid and the fluid does not smell burnt.
View 7 RepliesFord Ranger / B-Series :: 2003 V6 - Loud Shriek From Engine
Replaced serpentine belt and idler pulley today to stop this noise. Nothing changed but we eliminated anything near the belt. Tensioner had been replaced two years ago. Loud squeal starts slowly after starting then builds. It's constant and seems to come from the top of the engine where there are no turning parts. Both fans are running OK. Noise is synched with spinning of the engine. It's a 3.0 liter V6, vintage 2003. Appr. 63,000 mi. Any guesses?
View 7 RepliesFord Ranger / B-Series :: 2003 - Engine Knock On Cold Start
Specs: 2003 Ranger Edge / 3.0 V6 / 5-speed 4WD / 238,000 miles
Yesterday my truck was in the shop for repair. Intake gasket, Transmission fluid change, all heater hoses, thermostat, serp belt and coolant flush. When I picked it up from the shop, which was after closing, I noticed a knocking on start up. From past experience on a different truck, it sounds like a cam that isn't oiling. After a few minutes the knock goes away. I drove for a few miles, turned off the engine and started it back up and no knock this time. This morning I started it, knock was back but went away after a few minutes. Oil was changed about 1500 miles ago. Running pennzoil 5/20 with a K&N filter. Up until yesterday the engine has been completely quiet. Was wonder if something may have clogged the filter or the drain back valve.
Ford Ranger / B-Series :: 2003 - Engine Does Not Want To Start After Belt Replaced
I have a 2003 Ranger 2.3l with 327k miles on it. I recently replaced the belt and now it doesnt want to start. The belt is on correctly and tensioner is tight. The battery is fully charged its just not firing up and starting. All connections are good, the ac and power steering pulleys are relatively new. Now i have been stuck tryin to fix it for a week...
View 8 RepliesFord Ranger / B-Series :: 2003 - Check Engine Light Has Come On - DTC P2004
My check engine light has come on on my 2003 Ranger 2.3L 4V equipped Ranger. I have a Stinger code reader which shows a trouble code P2004. I havn't been able to find out what this code means.
View 14 RepliesFord Ranger / B-Series :: Missing When Started And CEL Came On
I have a 98 Ranger with a 3.0 (5 speed) that has 254,000 miles on it. I drove it to town this morning (8 miles) and it ran normally. I stopped for just a few minutes at a house and when I re-started the truck, it was missing very bad and the CEL came on. It wouldn't haul itself in anything higher than 3rd gear. I decided to try to make it back home. I drove it less than two miles and it cleared up and started running perfect again. I came home anyway and read the code with my scan tool.
It said that I had a miss fire on cylinder #5. I erased the codes and shut the CEL out and its been running perfectly ever since. (I have put about 150 miles on it so far) If it does it again, I will start by replacing the plug wires. I have already done that but its been a long time ago. The plugs have been replaced twice as well. I was wondering if it could be something other than electrical like a dirty injector or maybe the compression rings lined up and it momentarily lost compression.
Ford Ranger / B-Series :: 2003 3.0 - Misfire On Cylinder Six / Running Rough And Check Engine Light On
I have a 2003 ranger and have had ongoing problems with misfire cylinder six and have had three different mechanics diagnose the problem as a bad ground. I have replaced all plugs, wires, coil pack, injectors and am constantly pulling the plug on cylinder six, cleaning and often replacing, I also disconnect the battery so it resets the check engine light and it runs fine for about 100 miles and starts running rough again and on goes the check engine light. I have 134000 miles and have maintained it since new.....
View 4 RepliesFord Ranger / B-Series :: 2003 V6 - Squeal Sound Coming From Engine Compartment When Gas Pedal Pressed
Ok, my question is, when gas pedal is pressed half or more down-ward, a squeal sounding is coming from engine compartment. 2003 ranger v-6 3.0 flex....
View 1 Replies