Ford Ranger / B-Series :: Slight Squeak Noise Only Heard At Idle Some Of The Time
I have a slight squeak noise that is only heard at idle some of the time. I replaced the belt, idler, and tensioner when I noticed just spinning the alternator gives the sound I'm hearing. Is it something I should be concerned about? It isn't noisy all the time, only sometimes. I don't want to fix what isn't broken, but I don't want it to leave me stranded one day either.
View 3 RepliesFord Ranger / B-Series :: 2002 - Transmission Taking Time To Shift Into Drive
I have a 2002 Ranger with a 2.3 lt engine and a 5R44E Transmission. Has 120,oookms (75,000 miles) I have an issue.
Here is what was happening: Would not shift into Drive...took a long time to do so.... and had a 2 to 3 gear flare.
Here is what I did: Replaced the valve body gaskets. Improved a lot. The 2 to 3 shift flare has gone. The delayed shift into D is mostly gone BUT still takes 15 to 20 seconds to shift into D. Once in gear no problems shifting. Does not slip and NO OD light flashing.
What do I need to do to fix the delayed shift issue.
Ford Ranger / B-Series :: 2002 - Vibration And Grinding Noise?
Bought a 02 Ranger, 4.0 4x4 super cab 122,000 miles. etc Picked it up for 500 bucks because someone scrapped it along the side of a guardrail this last winter. Replaced rack and Pinion (cracked), Tie rods, Shocks, driver side knuckle and wheel bearing, and some body issues (bed is still shot so if any black short bed sitting around let me know). I've been kind of putting around all day in it, letting it used to working again. Starts right up, turns easily, I string aligned it so it goes where I want.
But as I get up to speed start at about 10MPG there is a vibration based noise coming from the front, can't pin down if its left or right. If Im going straight then turn it gets slightly more intense as I even start turning the steering wheel. The noise increases with vehicle speed. And I don't know if its separate or related, but any turn over 5-10* to the left results in a grinding sound but then I turn to about 10-15 and it gets less intense. No noise turning right.
I'm thinking a bad CV, TWO bad CVs, or a bad differential. Before I start ripping into those things, thought I'd get opinions, or hopefully experience in this area. I'm really hoping its something small and stupid. (like not getting a professional alignment)
Ford Ranger / B-Series :: 1998 - Belt Started To Squeak
I have a 1998 ranger 4.0 and about a year after getting it the belt started to squeak so far if have replaced the belt, replaced the tensioner, and cleaned and wire brushed all the pulleys to remove glazing. And it still squeaks and its annoying and kinda embarrassing...
View 4 RepliesFord Ranger / B-Series :: 1996 - Squeak / Chirp On Takeoff - Not At Idle
There's a small but clearly audible chirping/squeak coming from my truck whenever I pull out. It goes away after the truck gets hot, but for the first 10 minutes or so, it squeaks only when moving. Not at idle. It is worse at low RPM's in 1st gear. And it's particularly bad in the mornings. I was thinking it is something in the idler pulley or the belt tensioner.
View 7 RepliesFord Ranger / B-Series :: 2008 FX4 - Rear Leaf Spring Squeak
I've got an '08 FX4 that has developed quite a loud and annoying squeak from the rear leaf springs. It happens when I'm slowly applying power and going over bumps such as speed bumps or similar. More so when I'm going up hill.
I initially thought it was a u-joint going bad, and had my driveline mechanic take a look at it. He discovered it was the rear leafs making the noise. He sprayed them with an aerosol light grease and the noise was instantly gone. The problem is, the noise comes back after the grease spray has worn off (usually after driving in the rain) which happens a lot in the Vancouver area.
This is my 3rd Ranger and I have never had this problem. I don't drive in unusual places (beach, sandy, dusty areas) so I don't know why this is happening. It does look rusty in the areas that I can see in between the individual leafs. Is this a common problem for this vintage of Ranger?
Ford Ranger / B-Series :: Squeak When Running / Idler Pulley For The Timing Belt
In a few weeks I will be bringing my new to me Ranger back to the great state of Texas. The truck however, has a squeak when running, which I think has been concluded as the idler pulley for the timing belt. Well, I'm nowhere near the truck still and in order for it to get here it will need to be driven half a day to reach me, at which point I could do all the work it needs done.
My question is: Should I take the risk and have it driven here before the belt change (I did look at it while I was out there and it's already cracking pretty good), or should I go ahead and have someone get the belt done at a shop? It's less the belt that concerns me I think, and more the pulley, even though it's just started squeaking in the last 1000 mile.
Ford Ranger / B-Series :: Drive Shaft Was Hanging From The Rear End
I purchased a 1990 Ranger 4x4 with a v6 from auction. Took it to local shop to have them check it for me. Found out that it has a 3.0 in it and mechanic believes it is from a taurus. Truck actually runs extremely well. Has a few codes due to the ECM is for an automatic trans. Now the problem. I was on the highway-in 5th gear. Terrible noise the nothing. When I got it pulled over. The drive shaft was hanging from the rear end. It had been twisted like a straw. The transmission side had the yoke only, and the tail housing was cracked. It rolls and the drive shaft at the rear end turns. I figured the trans locked up. I don't know what trans to look for---is a 90 2.9 5 speed the same on a 3.0 ??
View 6 RepliesFord Ranger / B-Series :: 2007 - Shifts Into Gear But No Drive
My gf's dad said I could have his 07 Ranger 4.0 2wd with 230K on the clock if I fix the tranny 5R55E. One day he was driving home and all of a sudden had no drive. The tranny will run thru drive, neutral and reverse, but has no drive to it. Engine revs with nothing to show.
Tranny fluid was very dark and pan had nothing but the usual "metal flour" in it. I stopped there, did not pull the filter or anything else.
Ford Ranger / B-Series :: Trans Sometimes Takes A While To Go Into Gear When Put It Into Drive
I have a 98 XLT 4.0, auto trans with 109K miles and when it's really hot outside and it's been driven when I start back up and put it into drive it sometimes takes a while to go into gear. A friend says the transmission fluid doesn't look too good and it smells. Obviously I have a transmission problem but my question is would changing the fluid do any good at all? Since the tranny is bad what harm could it do? The fluid was never changed previously.
View 6 RepliesFord Ranger / B-Series :: 1997 - 5R55E Slips In Drive And Rev?
I have a 97 ranger 2wd 4.0 with 5R55E. Drives fine in 1st and second. Slips in drive and rev.
View 6 RepliesFord Ranger / B-Series :: 2004 - 4 Wheel Drive Vibration At 40 MPH
I recently replaced the oil seal on the front differential where the front drive shaft connects to the diff. I believe it is called the pinion oil seal. I had to remove the drive shaft to do the job. Got the oil seal in place and then slipped the u-joint yoke on and hand threaded the retainer nut on to get it started. I did mark the relative position of the drive shaft to the front yoke and the rear yoke. I had previously noted that the retaining nut, before I took it off had about 2.5 threads showing. I had to remove it with an impact wrench.
So...I used the impact wrench to put it back on with about the same number of threads showing. I then reinstalled the little short fronmt drive shaft...the one that comes out of the transfer case. I got the front of it on to the pinion output on the front diff...and then had to reattach it to the transfer case end which, by the way an interesting affair with a sort of metal cone that is attached by 6 8mm fine threaded bolts about 2.5 or 3 inches long. Got all that done with much grunting an groaning - I'm laying on the ground - SO the oil, leak is fixed but now ...
There is a vibration at around 40 mph and higher. like something is out of balance. did i damage the front diff pinion bearing by using an impact wrench? this vibration occurs in 2 wheel drive. as i understand it the front drive shaft doesn't even turn when in 2 wheel drive. my question is does the front diff gears spin when in 2 wheel drive? perhaps the u-joint is bad on the front drive shaft? just a bit baffled. when the speed drops to below 40mph the vibration goes away...
Ford Ranger / B-Series :: 1999 - Four Wheel Drive Will Not Engage
I bought a 99 ranger few months ago cant the 4x4 has not worked in the truck for about 4 years. Bought it off my dad. He hasn't figured it out the t case locks in the drive shaft spins but hubs will not lock in. Has new hubs in it and still not working. Trying to get it fixed so I can park the diesel for the winter and run the ranger.
View 3 RepliesFord Ranger / B-Series :: ABS Light Comes On Every Time Start And Drive Less Than 100 Yards
I have a 2000 4wd Ranger with rear anti-lock brakes. The ABS light comes on every time I start and drive less than 100yds. It stays on until you shut the truck off. I found the test plug, and followed procedures to get the codes, but the ABS light won't flash at all. I checked fluid level and fuses. I replaced the rear sensor about a year ago, when that went I lost speedometer and OD off light stayed on. I wouldn't rule the sensor out, but I'd like to get codes. To get codes I grounded the Black/Orange wire with the key in Run position.
View 10 RepliesFord Ranger / B-Series :: 2001 - Auto Trans Won't Drive / Reverse?
Daughter driving truck truck quits moving, I get there no drive and no reverse, has low and 2nd manually.
drive truck home, flush trans and cooler, road test all ok. this was 3 weeks ago.
This morning did it to here again, no drive and no reverse, she drove it home using manual low and 2nd.
I get in and when put into drive it feels like it tries but doesn't go all in, same with reverse. pulled it into low and vola I now have drive and reverse again
I'm thinking a we may have a bad or going bad shift solenoid. What I need to know is, is any of the solenoid valves on when in reverse are they the same as when in drive?
Ford Ranger / B-Series :: 2004 - 4 Wheel Drive Kick In And Out When Driving
My 2004 Ford Ranger has 220,000 miles, runs great, and when I bought it this summer the 4 wheel drive worked great. Starting when the weather got cold when I engage the 4 wheel drive (no lockouts electronic engagement). I will drive and it will kick in and out of 4 wheel drive when it starts to slip or I have to accelerate.
When the 4 wheel drive kicks out I will let off the gas then it will engage again on its own, but will slip out again when on ice or I start to slip. When the 4 wheel drive engages it does NOT make any strange sounds, no clunking or nothing, it engages smoothly, and disengages properly.
What it could be? a connection? Any way to fix or diagnose the problem? I have been told that it probably is not the transfer case, because if it were it would not engage or stay in 4 wheel drive at all.
Ford Ranger / B-Series :: Transmission Locked Out - Truck Would Not Move When Put In Drive
Last night I backed up out of a parking space and when I put it in drive it wouldn't move. It seemed like the transmission was locked up. What happened? The truck was running fine. It's a 2002 Ford Ranger 3.0 with auto transmission. Getting it serviced? I'm tempted to go to a dealer. What the problem is? Repair costs? The fluid looks good - no burning smell.
View 5 RepliesFord Ranger / B-Series :: 2007 - Rough Idle At Low RPM Either In Park Or Drive
2007 Ranger 4.0l, idles rough at low rpm, in park or drive, with or without the AC on.
View 1 RepliesFord Ranger / B-Series :: 2007 - Idle Roughly In Park And Drive?
The trucks seems to Idle Rough in Park and Drive, Cold or Hot. It mellows out as soon as I give it gas but at stop lights or in park it goes back to a seemingly rough idle.
This is my first Ford Ranger and dont know if its normal. No code or dummy lights.
2007 2WD 4cyl