Ford Ranger / B-Series :: 1989 - Signs Of Water Leaking Through The Gasket
My 89 2.9 has gotten water in the oil. One year ago I pulled this engine to replace the crank shaft (defective Ford design 1/2 thust bearing created a nasty grove in the crank allowing it to slide back and forth1/4 inch), new bearings, oil pump, timming chain, all seals and gaskets (not head gasket). The engine had great compression so I didn't do any thing more. Now I have a leak. No oil in water. NO compression leaking off into the water jacket. No "steam" coming from the exhaust. I've replace the intake manifold gasket. It showed signs of water leaking through the gasket, actually bubbles of water trapped inside, so I hoped this was it, but I still have water in the oil. I have now removed the intake and driver side head (head gasket shows now sign of leaking). No signs of water in cylinders. Is it possible to have a warped intake manifold? I have removed it twice, and I was told that some V6's need to be slowly removed VIA de-torque the bolts. I didn't do it the first two times I removed it, today I did. I plan to remove the passenger side head tomorrow. I will take the intake down and have it tested for warping. I have read many stories on this web site of the heads getting cracks, but they all seem to be in or near the valves, I assume that allows water to be burned off as a steam engine OR compression being pumped back into the water jacket.
Is there any other source of the leak that I'm missing? Is it possibly my intake? OR should I go ahead and replace the heads?
Ford Ranger / B-Series :: Water Temp Sensor Leaking / Missing Vacuum Hose
Was fixing leaking water temp sensor today and noticed the nipple under oil fill cap didn't have hose on it. After further investigation I found open spot on air intake hose with nothing in it. Both places seem to have vacuum, what goes here. BTW it is a 1999 Ranger ext cab with 3.0 flex engine and auto trans. Will try to get picture n post also...
View 8 RepliesFord Ranger / B-Series :: 1999 - Losing Coolant Internally / No Water In The Oil
1999 3.0. Been losing coolant internally. No water in the oil. Been back and forth on doing a full engine swap (its got 250k on it). So finally decided to just try the head gaskets. Anything out of the ordinary on these? Anything to look out for? Any special tools?
View 14 RepliesFord Ranger / B-Series :: Water On Floor Of Cab After Heavy Rain
When we have a heavy rain water leaks in on both sides saturating the floor board.
View 2 RepliesFord Ranger / B-Series :: 2000 - Changing Water Pump?
Plan on changing my water pump in the next day or two. Truck is a 2000 Ranger, 2.5L with 185,000+ miles. Just wondering if there are any hints/gotcha's that may not be in the manual.
Any advice on bleeding the coolant after I get it back together?
Ford Ranger / B-Series :: 1994 - High Oil Pressure / Water Temperature?
I have a 94 ranger 5 speed xlt v6 4.0l 288k miles original engine. in the last month the oil pressure has gradually gone way up. a manual gauge shows 65psi at cold start ( in the 90* out side) after a minute of idle it dropped to 60psi, at 2k rpms the psi was 85+. also the water temp has gotten hotter to the point of almost being unsafe. it appears that in the hotter part of the day the psi goes higher. the oil and filter was changed 1200 miles ago. the cooling system has been update in the last year with a new radiator new thermostat. no cross contamination in the fluids, engine runs good other than gauges on dash showing water and oil getting close to unsafe range and manual gauge showing high pressure.
View 14 RepliesFord Ranger / B-Series :: 1997 - Water Temp Gauge Does Not Work
Water temperature gauge doesn't work. Assumed the problem was the sensor so bought a new one. Installed it, still nothing registering on the gauge after I know the water is heated up (drove it for 45 minutes, heater blowing hot).
So crossed the ground on the sensor and the gauge shot to the top so gauge is working.
Pulled wiring diagram and that sensor is SUPPOSED to register 79ohms for cold and 8 ohms for hot.. So bought a 10ohm resistor from radio shack and attached the water temp lead to it and the gauge read correctly about 1/8 inch from the H mark on gauge. This confirmed for me that gauge is not at fault.
Next I attached the ohmmeter to the sensor itself, boiled some water, placed the sensor tip into it and it read 86 ohms, in freshly boiled water! So at boiling the sensor isn't anywhere near to tripping the gauge to even start reading cold! So I tested the old sensor that I was replacing and in boiling water it shows 94 ohms?
What am I doing wrong, is there an assumption I am making here in error? I want to conclude the new sensor is bad, but the old sensor reads nearly the same reading under same conditions.So yes maybe they are BOTH bad but that seems to be pushing probability.
If it matters this sensor is the type that is inline from radiator to heater core, not the type that is in the engine block, at some point ford changed their sensor setup but didn't change the schematic drawing. Which doesn't matter the only difference is the one in-line has a ground wire to it rather then grounding off the engine block.
Vehicle is a 97 Ford Ranger with the 2.0 liter engine.
Ford Ranger / B-Series :: Non Slider Rear Window Leaking
The rear window on my '99 Supercab leaks. I thought it was the cargo light so sealed it up good with silicone but still leaking. I have heard that the back glass is bolted in on these years..... It is a solid glass (non slider) ...
View 3 RepliesFord Ranger / B-Series :: 2003 - Intake Manifold Leaking?
'03 Ranger, 2.3L. Runs great except at idle. Code p0171. Replaced IAC, no luck.
Brake cleaner leak test definitely results in engine rpm change right around "butterfly rod" plug in front of intake manifold near no. 1 cyl. I'm pretty sure that's the problem - the plastic plug blew out. I watched a video showing repair, but it seems lacking.
I do not want to loosen up intake for access - I'd rather remove steering pump and gain some access to plug it up. There still isn't much access but, but eyeballing it, enough to plug, I think.
Three steering pump bolts came out easy. The fourth one is behind fluid line - extremely difficult to access, imo.
Somehow try to remove pump for access to intake hole, or bite the bullet and remove intake manifold for access?
Ford Ranger / B-Series :: 1998 - Oil Leaking Somewhere On Driver Side
I've been having to add a quart of oil between every 3,000 mile oil change. This is a used 2000 2.5L motor now with about 150,000 miles on it and 317,000 on my truck. I notice the oil is coming from somewhere on the side maybe in a few places. I think the oil plug is dripping a little. I'm going to try an OEM Ford plug because I've changed them several times with aftermarket plugs and they never seal right. I thought it might be the oil pan gasket but it doesn't really look wet around the flange all the way around.
Then I checked higher up thinking it maybe the valve cover gasket which has been replaced and it's drive around the cover. I noticed under the power steering pump bracket it's all wet with oil. It's not the power steering, I've never had to add to it. It appears to be in the middle under the intake. I didn't see anything from the pressure switch. It looks like it's mostly around the pcv valve box. Is there a gasket that leaks there? Or anywhere else that is common to leak? I fixed my transmission pan gasket leak which cleared up some of the mess on the bottom. How hard is it to change that pcv valve box? They call it a crankcase vapor separator where the pcv valve goes.
Ford Ranger / B-Series :: 1998 - Valve Covers Don't Seem To Be Leaking On The Outside
My '98 B3000 has an oil leak. There is some oil up high on bell housing. So a buddy and I thought it might be the oil pressure sending unit. I replaced it. And still seems to be leaking.
Maybe valve covers? I was thinking rear main until we saw it on the bell housing. Valve covers don't seem to be leaking on the outside. Do they leak worse on the inside of the V?
Ford Ranger / B-Series :: 2000 - Water Leak On Passenger Side Floor
2000 ford ranger, 2.5 2wd
Been having a little problem whenever it rains, the carpet on the passenger side gets soaked through and I'm not really sure where the leak is coming from. the only part of the floor that gets wet is the flat part where the passenger would put their feet, but the parts that slope up towards the dash and towards the middle of the cab stay dry. I've pulled up this part of the carpet, and the rubber grommets are intact and in good shape, and there is no rust or anything on the floorboard. from searching here it seems people have had similar problems, one thing being a leak into the seals around the third brake light above the rear window.
a couple things i should mention is that the air conditioning condenser has been broken for about two years, so could water get blocked up and leak in? since its winter here in PA i haven't used the air con since last summer though. I'm not really sure how long the leak has been happening since I've always kept a floor mat over that spot, and the carpet drys in a few days anyway.
Another thing i should mention is that the weather stripping at the bottom of the window on the drivers side door is not perfectly tight and tends to come out of place when the door is closed hard. this has been happening since i got the truck almost three years ago and a new piece was just put in a month ago (the leak had been occurring before the new piece was installed) when the truck was hit and went in for body work. possibly a drain routing to passenger floor? I should add that I'm sure it's not coolant, it has no odor and feels like water.
Might be a good idea to pull up the whole carpet on passenger's side and sit in the cab during the next storm...
Ford Ranger / B-Series :: 2004 - Slight Noise From Water Pump Area For A While
I had a slight noise from the waterpump area for a while, was waiting for it to fail but instead it was the clutched fan bearings. How difficult is it to repair? And could there be a recall on this, the ranger has 51,00 miles and its all easy miles. 2004 ranger 2.3 clutched fan bearing failure ...
View 14 RepliesFord Ranger / B-Series :: 1985 - Water In Oil / Small Leak At The Thermostat Housing
So I noticed when I check the oil, there is a very small amount of water at the end of the dipstick and also water mixing with oil around the oil cap. It is not much water at all, but my first thought was head gasket. I was loosing very small amounts of coolant, but found a small leak at the thermostat housing....The truck runs fine, idles fine, no bubbles coming from the radiator at startup, no moisture from exhaust. It seems to be using more oil than normal, but I drive it 100 miles a day still and no major issues other than the perplexing bit of water and oil mixing. Could it be a tiny head gasket leak? What else would cause the water and oil to come together.
View 13 RepliesFord Ranger / B-Series :: 2003 - Oil Build Up Under The Front End / Tranny Leaking?
2003 ranger 4.0 5 speed .... Pretty new to the car/truck world only 18 and this is my first truck, I traded my focus for it and so far so good. Its my first manual but i got to tinkering and i noticed some oil build up under the front end so i got to looking and found this, wondering if its an issue, should I try to fix whatever is causing it or take it to a mechanic. Looks like between tranny and engine to me.
View 2 RepliesFord Ranger / B-Series :: 1991 - Bad Head Gasket - Leaking And Coolant In Oil
I have a 91 Ranger V6 4WD with 150K that has been sitting for 7 years. The last time I drove it (7 years ago) to a mechanic, who diagnosed it with a bad head gasket - leaking coolant and coolant in the oil.
What am I looking at as far as a project: besides redoing the head gasket, what else will I most likely need to do given that its been sitting 7 years?
Ford Ranger / B-Series :: 1995 - No Spark / Leaking Head Gasket
My 95 Ranger has been a good truck in the 6 years I've owned it. I had to pull the heads to replace a leaking head gasket and wound up having the heads rebuilt due to weak valve springs and worn valves. I replaced the gaskets, installed the heads, get it all back together.....won't start. Fuel pressure is good. Found that there is no spark. While putting the crankshaft position sensor connector back on I noticed it didn't look too good. I replaced the connector and that's all I did and no spark. Long story short, after a lot of research, the coil pack, cps and coolant temp sensor were replaced and still no spark.
Everything has the proper voltage to it. After a little more research I found a post with the same basic issue. His issue wound up being the ecm. So I removed the ecm....it's a used one from a salvage yard. I've owned the truck 6 years so I have no idea when the ecm was replaced. It showed up today and will get installed when I get home from work. I also ran across posts about the camshaft sunchronizer and they should be replaced at about 80K miles. Since the truck has 289K I'll replace it. Still no spark. I'm hoping it's the ecm.
Ford Ranger / B-Series :: 1988 - Water Leaks Onto Passenger Feet After Heavy Rain
My 1988 Ranger has started leaking a gush of water onto the feet of passengers the first time I accelerate after a heavy rain. I saw the water flowing out from behind the glove box area as I started driving forward. How to fix this leak?
View 5 RepliesFord Ranger / B-Series :: 1994 - Coolant Loss / Head Gasket Leaking
I am working on my buddy's 1994 Ranger with a 2.3L I4 that has been going thru a large amount of engine coolant. The trucks has approximately 180,000 miles on it. When I had it parked on concrete I have not seen any signs of coolant on the concrete or any signs of coolant leaking. The next place I checked was inside the cab to see if there was any coolant from the heater core and there was not. The water pump has been replaced a couple of years back. I replaced the spark plugs today and did not see anything on the plugs that I would have thought were signs of coolant in the combustion chambers.
With that being said I have not worked on a vehicle with a leaking head gasket before. Would there be any visible signs on the sparks plugs? If so what would I be looking for? When standing in front of the vehicle with the engine running there is a slight smell of antifreeze being "vaporized". Are there any noted issues with this engine that would cause this? Are there any other things I should check? Could it be a leaking head gasket causing this? If so how can I check for that?